Knives By Purpose

GEC #15 Tidioute Boy’s Knife

I was just reading some statistics about Great Eastern Cutlery: in 2007 GEC produced approximately 7300 knives whereas in 2017 it’s nearly 30,000 pieces. This is remarkable in today’s hyper competitive EDC pocket knife market. That’s a 310% increase over ten years for a traditional knife company. Admittedly, these numbers are based on hearsay, but a glance at the production totals on GEC’s site show there’s some basis for them.

Buy the Boy’s knife at BladeHQ | KnivesShipFree | GP Knives

I’d like to think that the focus on traditional knives is born out of a perspective shift within the EDC community, perhaps away from the overbuilt tactical to the purpose-based smaller utility folders? It’s hard to say at this point, but just from observing the ripe secondary market it’s clear that slipjoint fever is on fire these days.

Today, we’re looking at the GEC #15 Tidioute Boy’s Knife, a well rounded and sized EDC slip-joint at a very accessible price point. Based around the traditional “Sleeveboard” pattern, these are sometimes also made into barlows with full steel bolsters. A “Boy’s Knife,” is generally characterized by their diminutive size (generally between 2.75″ and 3.25″ closed), the idea being these could be a child’s first pocket knife. These were most often spearpoint bladed pieces, but we’re seeing a lot of variety now in the modern iterations. But, before we get too far into that, let’s hit some specs:

Blade: 2.5”
OAL: 6.187”
Thickness: .43”
Blade Thickness: .09”
Steel: 1095 Carbon Steel
Weight: 1.8oz
Lock: Non-Locking Slipjoint

(These are my personal measurements made with my calipers and my faithful (pink) ruler. The manufacturer’s published numbers may vary.)

Blade

The #15 pattern by Great Eastern Cutlery is an amalgamation of several different knives they offer in the same size. I’m aware of a Wharncliffe version (Navy Knife), Wharncliffe with a cap-lifter/prybar type tool (Crown Lifter), Special Run Barlows (TC’s), and then the Spearpoint (Boy’s Knife) featured here. There are very likely other versions that I am not aware of out there, the world of GEC’s is deep and wide.

In my opinion the Boy’s Knife in spear point offers one of the more versatile blade shapes out of the GEC offerings. The blade has a straight back for nearly three-quarters of the length before descending into a fine point. GEC has also opted for a small swedge running nearly the entire length of the blade. I think that this offers a little dimensionality to what would otherwise be a very simple blade shape. In practice what I have found is that most of the knives that Great Eastern makes have very nice, thinly ground blades. Case in point, the #15’s blade I have has been taken down to .012 behind the edge… this thing screams through paper.

In practical use, I’ve found the #15’s blade to be a generally good fit for most of what I do. I think the spear point works well for piercing tasks and the thinness of the edge really excels for slicing. I wind up breaking down a lot of boxes at work and it only takes the lightest touch to break the tape.

As for steel, 1095 is a tried and true performer, high carbon, generally taken to 58-60HRC, I’ve had great experiences with it both in cutting and sharpening. It will stain or rust, so I’d suggest oiling the blade and spring with mineral oil or something similar (but not too much, some good use patina is cool.)

Handle and Ergonomics

The Boy’s Knife handle is a simple teardrop shape with micarta scales and a short steel bolster over steel liners. Construction is pinned. There are many options for scale material, but I opted for a micarta handle.

The handle offers a full grip for me, which is surprising to me since the knife appears to be so small on paper. The small teardrop shape doesn’t offer what I’d call a “secure grip,” but in the use case scenario for a small slip-joint, I tend to think this is more than adequate. When the #15 gets put to work cutting up cardboard boxes I’m careful with it as this is a smaller handle and the grip is not as secure as a full size knife.

I’d recommend a full size GEC if you intend to use the knife routinely for harder tasks like breaking down lots of boxes, but this knife is fine for light EDC use and the occasional package.

There is no pocket clip on this knife, so no need to comment on that. Often these knives are carried in leather slip sheathes. Either way this will be a small and slim carry.

Another option with this knife is to pick one up with a bail and chain. This is kind of like a wallet on a chain. It won’t walk off on you. Traditionally these bail knives were for sailors, and they continue to practical for marine applications and other times when you want to keep your knife on you.

Walk and Talk

Talking about the “lockup” on a traditional folder like this always presents a challenge, but I think it might be more applicable to talk about it’s fit and finish since those will directly relate.

The areas that are often talked about with traditionals generally are flushness of the spring and centering. I would expect a handmade custom Slipjoint to be flush in all three positions and perfectly centered, whereas I give a little grace to production knives.

The #15 is flush in the open and closed, but the spring does stick up a little at the half-stop. This would only become apparent if you stopped mid opening or closing to look at it. Centering, however, is right on the money.

Since this is a non-locking slip joint, we don’t talk about deployment and lockup. Instead we talk about “walk” and “talk”. The walk is the feel and tension of the blade moving against the spring, while the talk is the sound of the knife snapping open/closed.

The walk and talk on most GEC’s I’ve handled is pretty decent. My only gripe is that I don’t think that nail nicks are a viable method to open knives. My only interest in a nail nick is if it allows some portion of my finger to “stick” to the blade so I can pinch the knife open, and it barely functions as such on the #15. I’d love a more pinch-able blade.

GEC #15 Tidioute Boy’s Knife Review – Final Thoughts

All in all, my experiences with the GEC #15 have been very good. It’s a solid knife that performs well in the context that I think it was designed for. I think that most traditional knives perform pretty light duty tasks for everyone. Slice an apple here, open some mail there, maybe break down a few boxes as the need arises, but most of us won’t be carrying a GEC for a survival knife except perhaps as a tertiary backup to other gear. GEC’s have also maintained a good collector base, so if you’re the “Gotta Catch’em All,” type you will do well in this world.

If you are looking for a small and simple GEC slip joint, the #15 Boy’s Knife is well worth considering.

GEC #15 Boys Knife
From: BladeHQ

Editor: I recommend purchasing the GEC #15 Boys Knife at BladeHQ, KnivesShipFree, or GP Knives. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Kizer Sheepdog Review

by Dan Jackson 6 Comments

Imagine you can pick out anything from Kizer‘s lineup. I was recently put in that position. Not a bad place to be. Thumbing through their catalog yields all sorts of stuff from the pedestrian to the outlandish. The Sheepdog is more in that second camp. It’s a big bold design. Not likely to dislodge something like the FRN Chaparral from your pocket, but definitely a conversation piece.

Buy the Kizer Sheepdog at BladeHQ

No products found.

The Sheepdog is a design from Chris Conway of Sheepdog Knives, and is the production version of Conway’s C01C custom knife. The Sheepdog even has “C01C” laser engraved on the blade. It’s a big and chunky offering for fans of big and chunky knives. Clearly this one won’t be for everyone, but the unique design and loyal following piqued my interest.

This knife was provided to me free of charge from Kizer. All thoughts are my own.

General Dimensions and Blade Details

The Sheepdog has an overall length of 7.75″, a 3.125″ blade, and it weighs 6.17 ounces. Right now I have the open knife resting on my chest as I type this review out on my couch. The resulting sensation is what I would expect the early onset of a heart attack to feel like. It’s a heavy pressing weight, bearing down on my solar plexus. I better move this review along before my girlfriend has to call 911.

While the Sheepdog is categorized as an EDC knife, you will need to be a fan of BBKs (Big Beautiful Knives) to tote this one around.

For those seeking something smaller, Kizer wisely decided to introduce the Kizer Mini Sheepdog a while back. As part of the Vanguard series, the Mini Sheepdog comes with G10 scales and a liner lock, but it also clocks in at a mere 3.25 ounces. I received a Mini Sheepdog from Kizer as well, but stupidly forgot to take a size comparison photo before sending the Mini over to Grayson for review. I liked the size and weight of the Mini Sheepdog and could see that making for an interesting daily carry tool.

The Sheepdog’s blade is a massive slab of S35VN stainless steel. It’s a modified sheepsfoot, with a gently curving edge, high flat grind, and dual swedges. Sheepsfoot knives generally don’t have a penetrating tip, but the Sheepdog’s leading edge is canted out slightly, resulting in a strong tip that won’t pick out splinters, but could easily blow through a hollow core door.

The blade has been nicely made. The grind lines are crisp, the edge is clean and even, and the finish is a fine stonewash. No complaints.

Given this blade is a hair over 4mm thick, I was dubious of the Sheepdog’s cutting abilities. But much like an NFL linebacker, this big boy has some moves. I started with an apple, as apples are a great test of the slicing ability of a pocket knife. A slicey knife will cut the apple cleanly, while a chunky blade will plow through it, leaving a series of fault lines in your apple slices.

Much to my surprise the Sheepdog cut the apple cleanly. It’s like a small butchers cleaver.

I moved on to cardboard. No problems there either. The S35VN blade peeled through the cardboard boxes. It eventually slowed down as the edge dulled, but the edge geometry is good and the knife cuts well. After the boxes, I touched the Sheepdog up on the ceramic rods from my Sharpmaker and we were back in business. At that point I carried the knife with me. Mostly on the weekends when I could carry a big blade like this. It performed regular EDC tasks, including opening mail and packages containing other knives, without any issue.

Handle, Ergonomics, and Pocket Clip

Handle construction is simple and elegant. At the front of the knife you have an oversized pivot with an anodized blue titanium pivot collar. Towards the butt of the handle are two stainless steel standoffs. A series of three slots have been milled into the show side, offering a little extra traction and a view inside. Not much to see except for an expanse of dully shining titanium when the knife is open, or the glinting stainless steel blade when the knife is closed.

There is something oddly cathartic to the handle of this knife. It’s a hefty piece of contoured and bead blasted titanium, and it reminds me of palming a well worn river rock.

While the Sheepdog doesn’t have much of a “traction plan” with respect to aggressive texturing or jimping, the knife has clearly been built for comfort. Your hand naturally wraps around the handle, fingers finding the grooves, and thumb sliding across the broad spine of the blade. The result is a secure and confident grip without hot spots or ergonomic issues. I had no problems using my knife during the testing period. Granted I didn’t try to break down a yak with it, but for normal utility tasks the knife worked fine. I suppose you could always slap some skateboard tape on it, dudes.

The pocket clip is not without its controversy. First of all, it’s a milled titanium clip, so by default it’s going to raise the ire of a percentage of our knife loving brethren. I’m talking about those who have sworn their swords against the recent rebel uprising of milled pocket clips. Those folks will forever condemn the Sheepdog with its milled clip as a glorified paperweight, unfit for daily carry.

I’m a little less dogmatic when it comes to this sort of thing. Yeah, I’ve handled some knives with milled clips that didn’t work, but the one on this Sheepdog isn’t bad. It has been designed in a way to produce a lot of spring tension. Spring tension is critical for the success of any pocket clip, as this is what keeps the knife in your pocket.

The pocket clip works fine. I mostly wear lightweight shorts with a triangular pocket, and like to keep my knives high in the pocket up near my belt. Nothing upsets me more than a loose clip that allows my EDC knife to constantly sink towards the bottom of my pocket. That is the worst. Thankfully we don’t need to worry about that here. The Sheepdog’s pocket clip defies gravity and keeps my knife where I want it. No small feat given how heavy this thing is. Job well done, Kizer.

Ultimately, the Sheepdog carries well for what it is, but this is still a 6 ounce+ pocket knife. It isn’t a Dragonfly. You are going to notice it. It may even pull your pants down if you forget to wear a belt.

Deployment and Lockup

The Sheepdog makes use of an oversized flipper tab to get the blade open. The flipper is a substantial piece of steel allowing the user to pop the blade open with a lightswitch stroke. The detent is dialed in, and the blade runs on caged washers. The end result is a knife with reliable and satisfying flipping action. I’d put it at a solid “7” on the 1-10 scale. It gets the job done, but this is still a big heavy blade, and you feel that in the action. There is no jimping on the flipper tab, and I don’t think it needs it. My index finger has never slipped on the flipper.

For lockup we have a standard titanium framelock with steel lockbar insert. This is much like the Kizer Intrepid I reviewed two years ago. Kizer has the lock tuned to perfection. It locks up early, there is no blade play, and the lock is easy to disengage. There is no lock stick, and thanks to some contoured edges I can easily jam my thumb in place to release the lock bar. Much like the framelocks you find on a Zero Tolerance knife, this one just works.

Here is a parting shot of my Sheepdog next to the Paramilitary 2:

Blade centering is perfect on my knife.

Kizer Sheepdog Review – Final Thoughts

The Sheepdog is not for everyone. In fact, the Sheepdog is not for most people. It’s simply too big and too heavy. Despite that this knife has been well received. After carrying one for a while I can see why. It’s well made and functional. For those who want something big and chunky, the Sheepdog could be the one.

While the Sheepdog a big chunky knife, it is surprisingly light on its feet. The blade cuts cleanly, the knife feels good in hand, and it actually carries alright thanks to an especially strong milled pocket clip. And you can’t argue with the material selection or the fit and finish. Top notch materials combined with excellent fit and finish all lend a premium feel to this knife. That’s important given its ~$200 price tag.

The end result is a big but surprisingly refined knife. It isn’t for everyone, but I suspect that those that find themselves drawn to the Sheepdog will be pleased with its performance and execution.

No products found.

I recommend purchasing the Kizer Sheepdog at Amazon or BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Kershaw Concierge Knife Review

by Josh Wussow Leave a Comment

Dmitry Sinkevich and Kershaw are on a roll. Following the success of the critically-acclaimed Atmos, they’re leaping back into service with the Concierge – A slightly larger pocket knife boasting the same sci-fi elegance and everyday accessibility.

[easyazon_cta add_to_cart=”default” align=”center” asin=”B07BC93ML6″ cloaking=”default” height=”42″ key=”tall-orange” localization=”default” locale=”US” nofollow=”default” new_window=”default” tag=”brdfkdfk-20″ width=”120″]Kershaw Concierge[/easyazon_cta]

With an out-the-door cost of $38 at BladeHQ, the [easyazon_link asin=”B07BC93ML6″ locale=”US” new_window=”default” nofollow=”default” tag=”brdfkdfk-20″ add_to_cart=”default” cloaking=”default” localization=”default” popups=”default”]Kershaw Concierge[/easyazon_link] is a compelling entry point into the mind of one of the world’s premier knife designers. Its dapper handle houses a deceptively simple blade, ready to trim the foil from your morning champagne or cut the rind from your brie at brunch. I spent a few weeks chauffeuring this knife between work and play, thanks to the generosity of the folks at Kershaw. Here’s what I’ve learned over my stay with the Concierge.

General Dimensions and Blade Details

The Concierge boasts a contoured, upswept blade some 3.25-inches in length. The stock is rather narrow across the shoulders (0.11-inches), with a hollow grind outfitted in a dapper gray titanium nitride coating. Beneath this lies Kershaw’s ever-present 8Cr13MoV steel.

Now, I won’t go too far down the steel rabbit hole, since the similarly equipped Atmos has proven to be a capable worker. I’d still like to see something like 154CM or 14C28N on Kershaw’s budget models, but at least their 8Cr runs better than most.

The rest of the Concierge’s 7.25-inches is comprised of nicely crowned G-10, within which lies a stainless steel linerlock and KVT ball bearing system. Think about that for a second – Up until a few years ago, this would almost certainly have been running on Teflon or (if we were lucky) phosphor bronze washers. As it is, this newly affordable mechanism is sandwiched in a 0.55-inch thick handle, bringing the knife’s total weight to 4.3-ounces.

Now that we’ve covered the stats, let’s take a minute to talk about the knife’s real-world usage. The long, gentle curve of the blade is well suited for daily tasks. Its hollow grind had no trouble dealing with my typical mediums – apples, onions, cardboard, envelopes, and plastic wrap. The knife came sharp from the factory, and I’ve stropped it back to life with no issues. We’ll cover the details of the ergonomics in a moment, but I’m generally impressed with the everyday ability of the Concierge.

Handle, Ergonomics, and Pocket Clip

This is a knife that’s smooth all over – Like a tactical otter, or a slippery maitre d’. The subtle swells and arcs of the Concierge’s handle are really something to appreciate, especially when examined up close. Dmitry Sinkevich is known for his sleek, futuristic designs, and his style is in full force here.

The texturing of the G-10 handles is subtle and smooth. The large, dimpled pivot screws provide an interesting focal point for eye and thumb alike, and the chamfered steel liners are easy on the palm. I appreciate the jimping on the long backspacer, as well. Beyond its ergonomic appeal, it’s another point of visual grace in the knife’s overall design.

One of the more unique aspects of the Concierge lies in its recessed pocket clip. This single tongue of steel dips below level of the rest of the handle, thanks to a pair of unique cutouts. The tip peeks just above the horizon of the surrounding G-10, allowing users to slip the knife in and out of the pocket with ease. It takes a bit of practice, but I’m a big fan of the concept here. A recessed clip translates into a reduction of hot-spots in the hand, and Mr. Sinkevich has nailed its implementation. True, this means you’re left with a non-reversible clip. But for the majority of the knife-buying audience, this should be a hit.

Deployment and Lockup

The Concierge employs some of the best fit and finishing I’ve seen on a sub-$100 blade. But once we transition into the functional realm, several budgetary bugaboos rear their ugly heads.

Let’s start with the positives. The opening action is strong, thanks to a solidly designed detent. The blade’s long flipper tab is well-ground and smooth, preferring a button-style press to the old light-switch flick. As mentioned earlier, it’s great to see a KVT bearing system at a price point formerly reserved for Teflon or phosphor bronze washers.

So, deployment is a breeze. Stowage, however, is an entirely different story. My particular test model came with some pretty significant lock stick. Even after a thorough breakdown, cleaning, and repeated application of graphite and Sharpie, it’s still not a terribly smooth process. Combine this with the rather thin (though well-chamfered) lock bar, and you’ve got a recipe for tenderized thumb meat.

This removes much of the fidget-factor that made the Atmos so appealing. I’ve spent a decent amount of time messing around with the Concierge, and the lockbar hang-up isn’t as bad as it used to be. But, at least on my test model, the stickiness took some of the fun out of the experience. It’s a shame, especially given the KVT bearings and the perfect position of the flipper tab.

There’s also an odd note of metallic chatter upon closure, most noticeable between the disengagement of the lock and the blade tang hopping up over the detent. This is a minor issue, and I’m not concerned about the mechanical soundness of the lock system. But, it’s a small annoyance not present on the cheaper Atmos.

Kershaw Concierge Review – Final Thoughts

By this point, my preference should be clear – I ditched the $150 ZT0450 in favor of the Atmos, and the Concierge (while certainly a nice knife) isn’t going to kick its smaller cousin out of the collection. This is largely due to personal aesthetic (I prefer the uncoated blade), but the lock stick comes into play as well.

Minor production hang-ups aside, I still think this is an excellent knife. The recessed pocket clip and upscale aesthetic alone are enough to warrant the price of entry. I’d advise potential purchasers to adopt the try-before-you-buy attitude, in order to avoid picking up a model with the same lock stick issue I encountered. But, this is another strong collaboration between Kershaw and Dmitry Sinkevich. It’s a solid option at a respectable price, especially if the Atmos is too small for your palm.

[easyazon_block add_to_cart=”default” align=”center” asin=”B07BC93ML6″ cloaking=”default” layout=”top” localization=”default” locale=”US” nofollow=”default” new_window=”default” tag=”brdfkdfk-20″]

Editor: I recommend purchasing the Kershaw Concierge at [easyazon_link asin=”B07BC93ML6″ locale=”US” new_window=”default” nofollow=”default” tag=”brdfkdfk-20″ add_to_cart=”default” cloaking=”default” localization=”default” popups=”default”]Amazon[/easyazon_link] or BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

TRC Knives K-1 Review

by Andrew Gene Leave a Comment

The K-1 is from TRC Knives, a company out of Lithuania. It is run by Andrius Tricius who is also the maker. I’ve had the pleasure of reviewing another one of Andrius’ knives, the Apocalypse-L which has helped to give me a little more insight into his work.

Buy the TRC Knives K-1 at BladeHQ

Buy on Amazon

As with the Apocalypse, this knife leaves an immediate impression of quality. There aren’t any rough surfaces or inconsistencies in the symmetry from side to side. The sheath is cleanly made without damage or marks from thermo-forming and all of the surfaces are well finished, edges chamfered and holes carefully countersunk. From first glance the knife seems to have been CNC made by a high end manufacturer. On closer inspection it is much nicer with the subtle attention to details only a highly skilled craftsman will ensure are tightly buttoned up.

General Dimensions and Blade Details

The TRC K-1 has an overall length of 9.25″ (235 mm), a 4.52″ (115mm) blade, weighs 6.95 oz (197g) and 10.01 ounces (286g) with the sheath. This knife is made in Lithuania. The knife is best described as a camp knife or large fixed blade utility knife. With a 4.5″ blade, it isn’t going to work as a daily carry for most people.

The blade on the knife is made from Böhler Uddeholm’s Elmax. This steel falls into the category of powder metallurgy (P.M.) steels and offers exceptional performance. By performance I’m referring to its ability to take and maintain a keen edge and its corrosion resistance. As a P.M. steel it enjoys a healthy mix of some otherwise tricky to alloy materials (in high amounts) such as carbon, chromium and vanadium. The exact composition is as follows:

Carbon	Silicon	Manganese	Chromium	Molybdenum	Vanadium
1.7	0.8	0.3	18	1.0	3.0

There has been a bit of a buzz surrounding Elmax as being overrated. The heat treat is often speculated as being the culprit. Personally I’ve had a positive experience with this knife and Elmax in general. It is somewhat tougher to sharpen than what most people are used to and perhaps this is partly where Elmax looses some points. If you let your knives get very dull and aren’t an experienced sharpener than a lower hardness or less tough steel may be a better choice.

The blade profile is reminiscent of the classic Bob Loveless drop point. It has a good amount of straight working edge followed by some belly toward the end. The spine drops down to meet the tip (hence the name) creating a better point for penetrating cuts, adding to the versatility. The grind is a high flat that is sharpened with a secondary bevel.

The spine of the knife is “capped” meaning that it’s rounded. This detail resolves the shape nicely while making it more comfortable in use when bearing down on the back of the blade with your thumb or other hand. This K-1 has a satin finish but the model can also can be had in a stone-wash. The flats have a coarse texture that contrasts the smoothly finished bevels adding an attractive detail. At the plunge there is a deep choil for sharpening. TRC knives is etched on one side of the blade with K-1 on the other and Elmax on the handle spine.

Handle and Ergonomics

The handle is a full tang construction meaning that the supporting handle material travels out to the edges of the scales and is visible. The tang on the K1 actually protrudes a little further and is rounded off for comfort. Having this extra steel around the edges helps to both protect the scales and allow the pommel to be used as an impact tool.

The scales are thick Olive Micarta. Micarta uses organic materials like paper, linen or in this case Canvas as a reinforcement in a resin matrix. Unlike other similar materials such as G10 (also called FR4) or carbon fiber that use glass fibers, Micarta has a natural look and feel. On its outermost surface it also slightly absorbent. Even when wet, Micarta has excellent traction making it a solid choice for an all-weather grip. For fasteners the knife has flat topped bolts that require a three pronged driver. While the bolts give the knife a modernizing look and add to the design interest, you’ll need a special tool if you ever have to re-tighten them or want to take down the knife.

Ergonomically the K-1 checks all the boxes. The handle has a great thickness and as mentioned, the Micarta provides excellent traction. All of the corners have been skillfully chamfered preventing hot spots and supporting prolonged use. The blade has a short front guard followed by a finger groove to keep your hand firmly in place without worry of slipping onto the edge. The groove is complimented by some deep jimping on the spine for thumb placement that adds control and feedback.

At about 4.75” long the handle should fit most medium to large hands with or without gloves. Both the inner and outer edges gently curve and resulting in a natural grip. They terminate at a slightly flared pommel that helps to prevent slipping off the handle. There is a lanyard hole where you can add a wrist lanyard to further secure you to the handle.

Sheath

For carry the K-1 comes with a Kydex sheath. It has a two piece, sandwich construction with the halves being held by black eyelets. The eyelets are spaced for modular attachment points using fasteners like Tek-Loks or other M.O.L.L.E. type rigging. A nylon belt comes standard with the sheath and can be removed if desired. At the bottom there is a small drainage hole for aeration.

The retention is good while still allowing the knife to draw easily. Removing the K1 is helped along by a flared out corner at the mouth of the sheath. This allows you to quickly push it away with your thumb. Overall the sheath is well executed, uncomplicated and versatile.

TRC Knives K-1 Review – Final Thoughts

To sum it up, there isn’t anything I dislike about the TRC Knives K-1. It is an excellent fixed blade. I think that the overall dimensions and weight fit perfectly into my outdoor knife preferences. It has enough size and brawn to make it capable of handling some harder tasks but isn’t over-built.

If you are looking for a higher end, medium sized handmade fixed blade than this may just be it. If not, TRC makes other models on the larger and smaller end of the spectrum that I’m sure will be equally well made, function flawlessly and last a lifetime.

TRC Knives K-1s Fixed Blade Elmax Steel Knife, Black G10 Handle, Kydex Sheath EDC/Hunting/Bushcraft Knife

It is the compact version of our best selling model K-1.It feels great in the hand and features classic drop point blade profile.With its razor sharp edge, it is large enough to tackle any chore.
The spine is rounded with elegant jumping cut into it providing control and confident operation.
The scales are made of indestructible sandblasted G-10 to provide excellent traction.
Elmax steel 60-61 HRC (heat/cryo-treated) 3.7 mm/ 0.14 in thick Overall length: 215 mm/ 8.46 in Blade length from the tip to handle : 100 mm/ 3.93 in Handle: Black G-10, Comes with Kydex sheath, Weight: 145 g / 5.1 oz
Created by a legendary Lithuanian Master Knife Maker Andrius Tricius. Made in Europe.

Editor: I recommend purchasing the TRC Knives K-1 at Amazon or BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Additional Specifications:

Overall Length 9.25″ (235 mm)
Weight 6.95 oz (197g)
Weight With Sheath 10.1 oz (286g)

Blade:

Length: 4.52″ (115mm)
Thickness: .189″ (4.8 mm)
Steel: ELMAX 59-60 HRC (heat/cryo-treated)
Satin blade or stone washed blade

Handle:

Green Canvas Micarta (also available in black)

Sheath:

Kydex with detachable belt loop

Made in Lithuania

Giant Mouse ACE Biblio Review

by Aaron Shapiro 6 Comments

Wandering the hallowed halls of BladeShow in Atlanta can be an overwhelming and even intimidating experience. Knives are (not literally) being thrown at you right and left and it’s difficult to remember what you’ve seen, what you wanted to see, and what you haven’t been able to find yet. Several things stuck out to me during my time in Atlanta and high amongst them was the Giant Mouse ACE Biblio.

Buy the Giant Mouse ACE Biblio at BladeHQ

For those of you who haven’t heard of the Giant Mouse brand before, it is a collaborative production brand between custom knife makers Jens Ansø and Jesper Voxnaes; with the mission to design the highest quality production knife possible at the most reasonable price point they can. Over the past couple of years, I have had the opportunity to handle several knives from GM, but this was the first model that they produced with an ambidextrous clip which I need as a lefty.

The ACE line from GM is an unlimited production run of knives whereas the pure Giant Mouse lines are limited in production to 400 pieces per model. Currently, GiantMouse is offering two different models under the ACE umbrella, the Biblio (reviewed here) and the newly released Nimbus.

But first, as always, some specs:

Blade: 2.75” (with a cutting edge around 2.5”)
OAL: 6.75”
Thickness: .585”
Blade Thickness: .119”
Steel: M390
Weight: 3.8oz
Lock: Liner Lock

(These are my personal measurements made with my calipers and my faithful ruler, manufacturer’s published numbers may vary.)

Blade

The Biblio’s blade can best be described as a nicely bellied Wharncliffe. The blade has an ascending angle from the handle and terminates at a nice fine point. A nice thing about this shape is that when the edge is flat on a surface, the handle is raised above, allowing you to utilize the full length of the cutting edge without your hand interfering.

GiantMouse opted for a full flat grind as well, making this a pretty great utility slicer equally at home in the kitchen or campsite (not that these two need be separate). It’s ground thin and sharpened well straight from the factory. One last detail, GiantMouse has chosen to crown the spine on the blade, as I’ve stated countless times before this is a GREAT way to class up a knife.

The steel choice of M390 comes as an expected choice—the GiantMouse Knives are made in Maniago Italy by, I assume, Lionsteel who uses M390 in a lot of their models (Editor: I think Viper makes it, but I could always be wrong). I personally love this steel, it’s elementally similar to 20CV but manifests a finer grain that becomes apparent once you start sharpening it. I’ve always big a huge fan of M390 and request it whenever possible in custom orders. It’s been a solid performer, is very stain/wear resistant, and holds an edge well.

Handle, Ergonomics, and Pocket Clip

GiantMouse has opted to offer two handle material options for the ACE Biblio, either black G10 (which is accompanied by a satin blade finish) or green micarta (which comes with a stonewashed blade) both of which offer a nice grip and texture. The lines of the handle really lend themselves to locking into the hand, however, I do find that the grip itself is a little on the shorter side, with my pinky falling off the end—this is fixed if I choke up on the knife and utilize the large choil on the blade.

The clip is a simple wire clip that has the option for either “handed” carry. This is a simple method, but effective and has worked fine for me.

In the pocket, the GM is a squish on the thicker side, but being a liner lock you can’t expect much different. The ACE Biblio is far from the worst offender in this category.

Deployment and Lockup

I’ve always thought that having two different deployment methods on a knife generally meant that one took priority over the other. The Biblio, for example, has both an opening hole and a flipper tab but the detent is tuned for the flipper making it relatively difficult to open via the hole. That being said, using the flipper the action is smooth and snappy as expected with bearings.

The Biblio features your typical liner lock situation here, with a small bevel on each side of the lock to allow ambidextrous unlocking. My example engages fully, is solid in all directions, and hasn’t required any adjustment.

Giant Mouse ACE Biblio Review – Final Thoughts

Generally speaking, I think the GiantMouse project as a whole is a great exploration in what happens when two prestigious custom knife makers explore the production side of the knife-world without simply licensing a design or offering a mid-tech. Giant Mouse is a sole entity that operates within the design language of both Anso and Vox.

While I think that limiting the production runs of the of the GiantMouse offerings seems like a play for extrinsic value, it is nice to see that they have adopted an unlimited production run of affordable options.

The Biblio seems like a great choice for anyone that’s a fan of these two specific knife makers, wants a high-value option, or is looking for something that’s a little outside the “canon of normal knife brands.” The ACE Biblio is available (in Black G10) from BladeHQ for $175, and if you think about that… You’re getting an M390 flipper, designed by two well-respected makers, made to the exacting standards of (again what I assume to be) Lionsteel, for less than $200. Pretty hard to beat that these days, in my opinion.

Giant Mouse ACE Biblio – From $175.00
From: BladeHQ

I recommend purchasing the Giant Mouse ACE Biblio at BladeHQ. Please consider that buying anything through any of the links on this website (including Amazon) helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Microtech Halo VI Review

by Dan Jackson 14 Comments

“I tried being reasonable. I didn’t like it.”

Buy the Microtech Halo VI at BladeHQ

I always enjoyed that quote from Clint Eastwood, and couldn’t help but think about it as I wielded the Halo VI. There is absolutely nothing reasonable about this knife. Any justification that this would be my “new EDC” went completely out the window when I fired it for the first time and ~5″ of steel slammed out of the front with a terrific bang. Even more ridiculous is using the charging handle to recapture the blade. It’s something you would expect to see in a video game. This is a serious piece of hardware. It’s unlike anything I’ve ever owned before, and it revels in its unreasonableness.

But that’s part of what makes knife collecting fun. If everything was a Delica 4 there would be no point to it. Sure we would all have a practical knife clipped to our pocket, but the fun in collecting would be long gone. Thankfully we don’t need to worry about being confined to using a government knife to cut our government cheese any time soon. Unreasonable knives like the Halo VI are doing their part to keep the joy of collecting safely intact.

General Dimensions and Blade Details

The Halo VI has an overall length of 10.82″, a 4.5″ blade, weighs 6.5 ounces, and is made in the USA. It’s the closet thing I’ll come to owning a light saber. It’s big, it’s unwieldy. If comes from a long series of Halo knives. I won’t proclaim to be an expert on all things Microtech, but my understanding is that this is the first knife that the company produced. It’s a single action out the front automatic.

Here is a link to Microtech’s product page for the Halo VI. They give a detailed look at the knife in all its various configurations. Worth browsing if you are interested in the knife.

Here is a shot of the Halo VI next to my Microtech Stitch:

And as I mentioned before, the Halo VI is not a daily carry. In my book it’s mostly a collectible. Sure, it’s fully functional, and we will get into all of those details in the review, but it’s not a knife I see myself carrying. First of all, there is no pocket clip. Second, it has almost a 5″ blade. Third, it looks and sounds like a weapon of mass destruction.

My girlfriend, who is generally pretty cool with me having dozens of pocket knives scattered all over the house, is legitimately scared of this thing. I can only imagine how the old lady in line at the post office would react to me using this to trim packing tape. Probably by calling 911. Unless you are at a knife show there is no way you will be able to use this knife in public. It’s probably illegal for me to even take it out of the house without obtaining a concealed carry permit. On that note, you will definitely want to check your local laws carefully before carrying a Halo VI. This is not a knife that the general public will understand or appreciate.

But what the Halo VI lacks in practicality, it makes up in novelty. I think it may be the coolest knife I’ve ever owned. And I’ve owned some cool stuff over the years.

Lets check out the blade. At 4.5″ long, and over 4mm thick, it’s an imposing piece of steel. Microtech offers this in a modified drop point (or possibly a clip point) blade that they refer to as the “single-edge” or “S/E”, and they also offer this in an American tanto version with the “T/E” designation.

You also get your choice of serrations, and a number of finish options, including typical finishes like satin, bead blast, and stonewashed finishes. But they also have their “apocalyptic” finish, bronze, D.L.C., and then their painted finish shown here. Normally I’m not a big blade coating guy, but this is what was available with an unserrated edge, so that is what I got.

My blade is made from Bohler M390, a blade steel that needs no introduction at this point, seeing how we have reviewed dozens of knives running M390 by now. It’s a high end stainless steel and is widely considered to be one of the best steels for an EDC knife on the market today. It has that enviable combination of holding an edge for a long time while still being easy to sharpen. Usually a knife steel will either be extremely hard, so the edge holds a long time, but it’s very difficult to sharpen when the knife dulls. That’s not the case with M390, which is why it’s such a popular choice on high end pocket knives. It also finishes nicely, doesn’t chip easily, and is a stainless steel. It’s good stuff.

Given that this knife is a collectible, and not a practical EDC item, I haven’t done a ton of cutting with it. It came very sharp from the factory. It’s not a great slicer due to the thick blade and partial flat grind. It forms a wedge, kind of like a splitting maul, and will pop apart an apple rather than thinly slicing it like a Swiss Army Knife. But that’s OK. They didn’t design this thing to slice apples.

Handle and Ergonomics

A 6.125″ milled 6061-T6 aluminum handle encapsulates our big blade. If a black handle is too pedestrian for you, Microtech offers these in almost every color under the rainbow, including a couple camo variants. I’m fine with black, but then again, I’m boring.

The handle is held together with Microtech’s proprietary hardware. Normally this would be the part of the review where I bitch about proprietary hardware, but I have no intention of taking this knife apart. If there is ever a problem I’ll send it back to Microtech.

The fit and finish on this knife is absolutely top notch. It’s a precision machined piece of hardware. I can’t find a gap, unexpected sharp edge, or flaw anywhere. This may not be the most practical tool, but you have to admire how well it is built.

The Halo VI feels good in the hand. It’s kind of like a small light saber. There is no lack of real estate, and Microtech has created a funky pattern of jimped curves to it that adds some visual interest as well as spots for your fingers to rest.

I suppose the most practical application for the Halo VI would be in a martial arts capacity. I have no training in that regard, so can’t comment on the efficacy of the design in that role. As a layperson, I can tell you it feels fine in hand. There is plenty of room to grip this knife, and you can do so in a number of different configurations. The hard anodizing provides a tiny amount of traction. It’s not slippery, but it isn’t sand paper either.

The Halo VI doesn’t come with a pocket clip. Probably for a reason, as the last thing you would want is for this knife to accidentally deploy in your pants. Even with the new safety, I’d rather not take that risk. And with a closed length of over 6″, it’s not a pocket friendly knife anyways. I’d probably go with an Scarab or Troodon instead for daily carry.

It seems like the best option for carrying your Halo VI is with a sheath. You could requisition a large enough magazine pouch, make a sheath, or have a leather or kydex sheath made for it. There are companies that specialize in making aftermarket sheathes for the Halo VI. Linos Sheathworks currently has a kydex sheath on offer for less than $50.

Deployment and Lockup

This is where we get to the good stuff. This is a single action out the front, which means the blade fires out with a press of the button, but need to manually retract the blade when you are done by pulling back on the charging handle. Contrast this with a double action out the front, where the button is used to both open and close the blade. With the case of a single action Out-The-Front (OTF) automatic, all the spring power has been assigned to ejecting the blade. It’s a lot of fire power. Ejecting the blade of this Halo VI is arguably the single most satisfying knife event in my history as a reviewer. It’s fucking awesome.

For this 6th generation of the Halo, Microtech added a small safety to the firing button. This prevents you from accidentally firing the knife. Not a bad idea, especially if you are crazy enough to carry this thing loose in your pocket. The safety is built into the firing button. You pull down on it ever so slightly, and that allows you to depress the firing button and let the blade loose. Generally I’m not a fan of safetys on folding knives. They tend to get in the way. But this safety has been beautifully executed. Purists may not be a fan of this new addition, but I think it has been done so that it doesn’t get in the way of using this knife.

For lockup, this is essentially a button lock knife. So inside there is a cam that holds the blade in place. One of the prior issues with an OTF knife, is that you tend to get blade play in them. That is especially true for the double action OTF’s I have handled. I haven’t handles a Halo V to see what kind of play, if any, is in that knife, but I can tell you this Halo VI has no play in it. It’s absolutely rock solid.

Retracting the blade is a two handed affair. First you need to depress the button. Once again that requires you to use the built in safety. With the button depressed you then pull on the charging rod to recapture the blade. It takes a good amount of force to overcome the spring tension and bring the blade back. The blade slides back in place with a sharp metallic twang. It’s a great sound. I’ve never armed a bear trap, but I would expect it to sound something like recapturing the blade on a Halo VI. It’s significant and satisfying.

The charging rod and the mechanism that holds it into the handle is worth examining. It’s all precision machined. The retaining mechanism is a couple spring loaded tabs. Everything reeks of quality and when the charging rod is in the handle all the parts line up perfectly. I’ve taken a couple detail shots of this, but it has all been beautifully done.

Here is a parting shot of the Halo VI next to my Paramilitary 2. It gives you a good sense of how huge the Halo VI is.

Microtech Halo V.I. Review – Final Thoughts

The Halo V.I. is a lot of fun. It’s also completely ridiculous, which is sure to turn off some people. I’ve been writing knife reviews since 2010, so it’s taken me almost a decade to get around to reviewing a single action OTF. This is a knife that retails for $650, so the expense is one of the reasons I delayed this purchase, but the fact that this is not a knife I can carry and use is the biggest reason why I waited so long to buy one. I like my tool knives, and this Halo V.I. is about as far away from a tool knife as I can get.

But that doesn’t make the Halo V.I. any less fascinating. Part of what makes this knife so satisfying is how well built it is. This is a design that has been refined for 25 years, and it shows. Each detail has been considered and Microtech does a fantastic job with their machining. The resulting knife is borderline obscene, but it has been so well done I can’t help but be impressed with it. Much like the Rockstead Higo I reviewed a while back, it tests the outer limits of what is possible with a production knife.

But as I have continued on my journey of exploring production knives, I’ve ventured further and further from the Benchmade Griptilians and Spyderco Delicas. They are still great, and I plan on continuing to review practical knives, but exploring the outer limits is fun too. This Halo V.I. is certainly out there, but it is so well done that I can’t help but appreciate it.

Accordingly, I can’t recommend this knife for everyone, but if the Halo VI intrigues you, I’m here to say Microtech didn’t cut any corners. Recommended for unreasonable people that that like the idea of a high end single action OTF automatic.

Microtech Halo VI – From $650.00
From: BladeHQ

I recommend purchasing the Microtech Halo V.I. at BladeHQ. Please consider that buying anything through any of the links on this website (including Amazon) helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.