EDC Knives

Spyderco Bradley Folder 2 Review

I’ve set some odd goals throughout my life. Goals that are a personal measure of my own success. One of those goals was to carry a Spyderco as an EDC knife. I always associated Spyderco with expensive and high quality. Why? I’m not exactly sure. Realizing that knives from companies like Microtech can cost 5 times as much as a Spyderco didn’t change my mind. To me a Spyderco was a measure of a certain kind of success.

Buy the Spyderco Bradley Folder 2 at BladeHQ

Buy on Amazon

I had a bit of a rush when I finally purchased my first Spyderco. This is my third Spyderco and I get that same rush. The Spyderco we are talking about today is the Gayle Bradley Folder 2. The Spyderco Bradley Folder 2 has been my EDC for most of the fall and winter so I’ve had the time to get to know it.

We all know who Spyderco is and we know they produce high quality knives designed for hard work. Gayle Bradley may be familiar to some readers, but let’s talk about him a bit for those who aren’t familiar with his work (we previously reviewed Bradley’s original collaboration with Spyderco, and the Spyderco Air as well). Gayle Bradley has been designing knives for over 30 years. His knives have set Blade Sports world records twice and stay in high demand. The calling card of his knives is the combination of form and function.

Gayle Bradley’s knives work and look good doing it. The Spyderco Bradley Folder 2 is no different. The collaboration between Gayle Bradley and Spyderco has produced my favorite Spyderco yet.

General Dimensions and Blade Details

The Bradley Folder 2 has an overall length of 8.48 inches, has a 3.66-inch blade, weighs 4.5 ounces and is built in Taiwan. Since it has a 2 in the name you can assume this is the second Bradley and Spyderco collaboration. The Bradley Folder 2 is longer in both blade and handle than the original, but remains the lighter knife. The Bradley 2 is a half an ounce lighter than the original.

This knife is too pretty for me. It’s so good-looking I almost hate to carry and abuse it. As you can see from the pictures I seemed to have gotten over that. I’ve used and abused it quite a bit. The handle features carbon fiber and G10 laminate grips. This gives the knife it’s eye catching outward appearance. It’s not until you spend some real time with this knife you appreciate it’s refinement. Once you get to third date you can take a peek under the skirt.

The blade is hollow ground and the symmetry is painfully perfect. The way the grinds on the top of the blade catch the light is something you can only experience with one in your hand.

The blade is made from CPM M4 steel. The benefits of this steel are numerous. It’s strong, it holds an edge forever, and it can be razor sharp with little effort. The knife gods can’t give without taking though. M4 is a tool steel and not a stainless steel so it will rust if you don’t take care of it.

My blade isn’t rusted, that’s tar. I’ve been re roofing my home and the Bradley Folder 2 has been along for the ride. Once I have the time I’ll sit down with some blade oil and a stiff AP brush and try to clean it. For now, it just adds character.

From the factory the blade is a razor. It sliced through any and everything with ease. Paper, roof shingles, cardboard, rope, and more. Dragging it over certain materials was enough to make cuts. I remain impressed by how sharp I can get this blade. Equally impressive is how long it remains sharp.

Handle, Ergonomics, and Pocket Clip

The extended handle on the Bradley Folder 2 will be appreciated by anyone with XL hands. The design includes a subtle finger guard to help resist hand slippage when working hard. The rear of the handle has an inward curve that accommodates a thumb on top grip. The screws that hold the grip panels to the knife are countersunk and blackened to blend in with the grips. There is a total of 8 Torx screws in the grips, 4 on each side.

That carbon fiber pattern offers you a grippy texture. It helps keep the knife in your hand, but isn’t abrasive or uncomfortable. The pattern itself is not just nice to look at, but functional.

The back of the blade has a small textured session to rest your thumb on. It’s nice but it could be bigger. There is plenty of room to extend the texturing if they chose to do so. The blade is easy to control for fine cuts and the handle is comfortable during long stretches of work.

Included is a simple, but long pocket clip. It’s 2.5 inches long and adorned with a cute little Spider. The pocket clip can be moved to 4 different positions. You can carry the knife tip up or tip down and it can be orientated for left or right handed carry. The Bradley Folder 2 is a completely ambidextrous knife.

Deployment and Lockup

The Bradley Folder 2 has a larger ½ inch deployment hole. When it comes to Spyderco’s deployment hole design you either love it or hate it. For me it’s easy to reach and puts the blade into action fast enough. It’s far from the fastest deployment system, but its smooth and reliable. There isn’t a little piece of metal screwed to the side of the blade that’s waiting to fall off.

Once the blade is locked in place it’s staying there. The blade has zero play in any direction. You can feel the slight hiccup right before the liner lock engages. This the only point where deployment isn’t 100% smooth. The liner locked is textured which is a nice touch. This makes it easier to unlock the knife, especially when your hands are cold and numb.

Spyderco Gayle Bradley Folder 2 Review – Final Thoughts

The Gayle Bradley Folder 2 is a great little knife. It mixes both form and function flawlessly. It gives users something they can admire with the hand and the eye. The Bradley Folder 2 is a workhorse. Just because it’s pretty doesn’t mean it can’t get dirty. This isn’t the cheapest Spyderco, and you are probably paying a little extra for the looks. Are looks worth it?

Well, that’s subjective. To me, it’s worth every dime. I think it’s a fantastic knife and it will likely stay in the carry rotation for some time.

Sale

Spyderco Bradley Folder 2 Specialty Knife with 3.66" CPM M4 Premium Steel Blade and Black Carbon Fiber Laminate Handle - PlainEdge - C134CFP2

Folding Knives: Locking folding knives are safe, compact, and easy to carry. They also happen to be where the Spyderco revolution began.
Carbon Fiber: Graphic fibers (the size of a human hair) woven together then fused with epoxy resin. Lightweight with a high level of tensile strength it is three dimensional in appearance.
Hollow Grind: It comes with bevels that are ground with a concave radius. The bevels may extend the full width of the blade (full Hollow Grind) or only a portion of its width.
PlainEdge Blade: This knife has a sharpened blade with no serrations or teeth sometimes referred to as a smooth blade.
Specifications: Closed Length (Inches): 4.82, Overall Length (Inches): 8.42, Blade Length (Inches):3.6, Blade Steel: CPM M4, Grind: Hollow

Editor: I recommend purchasing the Spyderco Bradley Folder 2 at Amazon.com and BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Kizer Gemini Lefty Review

by Aaron Shapiro 1 Comment

Ray Laconico has been a favorite knife maker of mine for a long time. Over the years that I have been buying and selling custom knives I’ve had the opportunity to own two different customs from Ray. His style is simplistic, but with a very unique aesthetic that sticks out on a table full of titanium knives.

Buy the Gemini at BladeHQ

Buy on Amazon

The Kizer Gemini, a production version of the famous Jasmine, came out a few years ago to much fanfare and excitement, it was a chance for everyone that wanted a piece of Ray’s designs to be able to get it, at a price that would encourage them to put the knife to use.

Kizer also has been making ripples in the EDC cutlery world, largely because of the fact that they seem to have mastered the ability to partner with custom knife makers and create extremely high quality versions of their knives. They’ve successfully done this with a number of notable makers including Matthew Christensen, Sheepdog Knives, Mikkel Willumsen, and a handful of others. Let’s get into some specifics.

General Dimensions and Blade Details

The Gemini has an overall length of 7.25″, a 3.125″ blade, weighs 3.6 ounces, and is made in China. Kizer makes a more affordable Vanguard series version of the Gemini. Ben Schwartz reviewed that one in 2016. And although this review is of the lefty version, it just as easily applies to the regular Gemini. The only difference is that the knife has been “mirrored” and the lock is now on the other side.

The Gemini has a traditional “leaf” style drop point blade. Very similar in a lot of ways to some of the popular offerings from Spyderco. This blade shape excels, in my experience, for general EDC use. The full flat grind peels layers away when you’re slicing through food or other materials, it’s easily sharpened without any tricky recurves, and the 3” mark is right in my sweet spot for daily carry.

S35VN steel seems to attract a little bit of controversy, my experience with it has been pretty good however. It takes a good edge on my Wicked Edge, and will hold it through a lot of work (in particular a lot of cardboard boxes). As an aside, I think that sharpening your own knives can be a good exercise in understanding how steel preforms under wear. Lots of people talk about wear resistance, toughness, and edge retention but I have found that these characteristics present themselves best during sharpening.

Kizer stonewashed the blade on the Gemini. Stonewashing comes in many flavors, this one is very similar to the stonewash CRK uses on their knives. It repels wear, and looks really sharp (ha) over time.

Handle, Ergonomics, and Pocket Clip

The handle is contoured Titanium, that have been blasted to a satiny matte finish. The handles are rounded (kinda like a river stone) to be comfortable in hand. There’s something to be said about the knife being a little slippery but its a tradeoff in my opinion.

The handle’s design is simplistic, flaring out towards the pivot to contain the mechanics, and tapering as it moves backward. The spine of the knife rises up a bit to create a very effective palm swell when you grip it. There is a negative angle on the handle that descends down into your grip, between that and the choil formed by the flipper tab when opened the grip is pretty firm and stable when the knife is opened. With the knife closed the pocket clip acts as a nice guide to rest your fingers on when you flip it open, doing this helps keep your hand off the lockbar.

The clip that debuted on the Gemini was a (frankly) cheap bolt on bent Ti spring clip. It was a real speed bump visually for me on the knife. In the newer iteration Kizer has created a milled Ti clip that compliments the design very well. It’s mounted with two screws to the lock side and leaves roughly half an inch visible when it’s in the pocket.

I want make an important point when it comes to a knife’s pocket clip. You likely use the clip more than you use the blade. It’s what holds your knife in your pocket and keeps it from falling out. While doing this, the clips also have to be trim enough to not catch on anything, rounded enough to not cause a hot spot when you use it, and attractive enough to not completely mess up the lines and aesthetics of a reasonably expensive knife.

I’ve seen and handled the first generation of Kizer Gemini, the original clip was really awful at several of these points, but the updated clip solves those problems.

Deployment and Lockup

The Gemini is a titanium frame lock flipper, the tried and tested configuration. One of the things that stands out about Laconico’s custom pieces is their flippability. The knives I’ve owned from Ray have been smooth, with perfect detents, and excellent lockup. The Gemini is no different.

Kizer incorporated a steel lock insert on the Gemini to ensure lasting lock strength and to guarantee that there won’t be any lock stick. The steel lock bar insert trend in production knives is an interesting one to me, in theory it’s the best way to give a frame lock the longest life possible. Late lock up typically occurs as the harder steel tang on a blade rubs against the softer titanium lock face, the blade side of the frame lock over time grinds away the surface of the lock bar’s lock face. Replacing the Ti side of the lock with steel prevents this, it also prevents galling (lock stick). Additionally the steel insert acts as an over-travel stop preventing you from hyper extending the lock bar when you unlock it.

One of the things that always stood out about Laconico’s custom knives is their flipperability (That’s a technical term we use in the industry to describe how well a knife flips. -Ed.). Kizer employed a similar caged bearing system in the Gemini to ensure smoothness and ease of opening. It’s a tried and true method, and Kizer executed it well.

Kizer Gemini Lefty Review – Final Thoughts

So, to wrap up the Lefty Gemini in a nutshell, I think it’s a great value. You’re getting a full titanium, S35VN, steel lock-bared, knife. The fit and finish is excellent, and it’s a great way to get introduced to Laconico’s work without spending custom knife prices.

It’s also worth commenting on the left handedness that Kizer has embraced. Being lefty was what pushed me into buying custom knives, I didn’t like having to adapt myself to use production knives. Whenever I see a company that offers a specifically left-handed option, I try to at least buy one to support that gesture. If you’re left handed, I encourage you to do the same, and if you’re right handed… Well, the Gemini is still a great choice.

Kizer Gemini Framelock

I recommend purchasing the Kizer Gemini at BladeHQ or Amazon. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Boker Patriot Review

by Dan Jackson 5 Comments

Last Updated: August 30, 2019
The Boker Patriot started with a great premise. A lightweight, affordable utility knife made in the USA with a 154CM blade. Who can argue with that? I for one was excited about the Patriot.

Buy the Boker Patriot at BladeHQ

Buy on Amazon

But for whatever reason it hasn’t gotten a ton of traction. I say that because the Patriot only got a handful of reviews on Amazon. Hardly any. Contrast that with the Delica 4, which has about 1,500 reviews. Granted the Delica has been around for decades, but still. When a $70 knife released a couple years ago has a grand total of 5 reviews on Amazon, it makes you question its commercial success.

But that doesn’t dissuade me. If I bought my knives solely based on what the bright bulbs at Amazon suggested, we would be flooded with Gerber Gear (Bear Grylles edition – yeah!), M-Tech, and iridescent gas station knives. Thankfully I have too much self-respect for that. Just barely.

So when our very own Ben Schwartz told me he had a Boker Patriot for sale, I jumped at the opportunity. But it gets better. Ben is such a generous guy he gave me the knife. Thank you, Ben. I’ve wanted to check this one out for a while. I need to return the favor.

General Dimensions and Blade Details

The Boker Patriot has an overall length of 7.5″, a 3.375″ blade, and weighs 2.11 ounces. It’s a great size for EDC. Light, thin, but full size and uncompromising in utility. And the Patriot is nicely made. All the parts line up. Good fit and finish. A satisfying knife that gave me a good initial impression right out of the box.

The Patriot comes with a compressed drop point blade. Low slung and thin, it’s the perfect size for getting under the corner of an envelope, or slicing away at errant packing tape. Despite this you still get some belly and a fine tip. The knife also has a high flat grind and has been left with a satin finish.

One thing I noticed is that this blade came screaming sharp out of the box. Sharp enough where I still remember it, and I’ve had this knife at my office for several months now. I use it mostly for mail, but I’ve taken it to task on some other EDC chores. I brought it home a couple weeks ago and have been EDCing it on the weekends. Out of the box sharpness is only a minor facet of a knife review. After all, you are going to need to sharpen a knife anyways, but I noticed it here.

And the Patriot has held onto that sharpness for a long time. I’ve been using this knife casually for a few months now, and I have yet to sharpen it. It’s made of 154CM, which is a nice steel, especially at this sub $75 price point. Excellent stuff. It’s got a fine grain structure and takes a great edge. For regular duty EDC chores 154CM will hold strong for a good while.

So the blade and steel are both excellent. Perfect for daily carry tasks.

Handle, Ergonomics, and Pocket Clip

The Patriot’s handle is comprised of glass filled nylon handle slabs, a plastic backspacer, and a stainless steel back lock. The handle is held together with high quality torx fasteners. This knife is linerless, so I wouldn’t use it for anything but cutting chores, but it feels remarkably solid. They offer the Patriot in a number of colors, including standard black. Orange is a good change of pace. There is no losing this knife if you drop it on the forest floor.

I know some will poo-poo the Patriot due to its plastic handles, but I don’t mind a plastic handled knife when it’s done right. And here it has been done right. The plastic pieces have been finished nicely. No gaps, no extra plastic left over from the molding process. It doesn’t feel cheap. And the satin hardware contrasts nicely with the matte handle. There is also an unobtrusive lanyard hole for those that like lanyards.

In hand the Patriot feels secure. It’s a thin handle, but thanks to some smart ergonomic decisions the Patriot fills the hand and is comfortable to use. First, the handle is relatively thick. Not Cold Steel Voyager thick, but thick enough to provide something to hold onto. Then they have included a couple finger grooves. This can be hit or miss, but here the grooves work perfectly for my hands. A short row of jimping provides ample traction for your thumb, and there is a forward finger choil on the blade if you want to choke up. It’s a small finger choil, but it works. Rounding things out is a high traction triangle pattern on the handle.

The end result is that the Patriot is comfortable to use. It feels natural in the hand in both forward and reverse grips. There is a lot of traction, so if you decide to use this for food prep, hunting, or some other messy chore you won’t be disappointed. But the knife is still comfortable thanks to the molded edges.

The pocket clip is a standard stainless steel deep-carry clip. It is simple but effective. Spring tension is about perfect. The knife is easy to insert and remove from the pocket, yet it remains securely in place. It’s also swappable for left or right handed tip up carry. It has good tension and is relatively discreet.

The Patriot carries easily. It’s a lightweight knife with a sturdy clip, so you quickly forget about it and there is little chance of it falling out of your pocket. I will say that the aggressive texture of the handle can make this a pants shredder. I won’t use this knife with suit pants or slacks, but it’s fine for my $15 K-mart shorts.

Deployment and Lockup

The Patriot is a thumb stud knife. If you have read my last few reviews you would have thought I forgot about these. Everything is a flipper these days.

But the Patriot comes with two thumb studs that appear to have been bolted onto the blade. The thumb studs are prominent and I can flick the knife open with my thumb most of the time. There is a decently strong backspring, so adequate force needs to be applied to pop open the knife. All things equal I prefer the more reliable thumb hole of a Delica over this, but it’s not bad.

The action is smooth and fluid. Peering into the handle I can’t see washers, but would be surprised if there were not phosphor bronze washers hugging the pivot of this knife.

For lockup we have an old school back lock. It’s actually more like a mid lock. It has a Boye Dent (the little dent on the lockbar release), which makes the knife more difficult to accidentally disengage. Lockup is secure. The blade falls into place with a satisfying snap.

Here is a shot of the Patriot next to a Medium Cold Steel Voyager:

There is no blade play in any direction, a remarkable feat given this is a liner-less plastic handled knife. Delicas and Enduras are notorious for up and down play. Cheap plastic lock backs like the Ka-Bar Dozier Folding Hunter often have some play in them. A little blade play isn’t the end of the world, but its absence here goes to show that the Patriot is firing on all 6 cylinders.

The blade centering on my knife isn’t perfect. It’s maybe off by a mm. Still “centered” and not rubbing, but not perfect.

Boker Patriot Review – Final Thoughts

The Patriot is an excellent mid-priced EDC knife. The market has become so top heavy expensive knives that it has become easy to lose track of more humble offerings like the Patriot. But ignoring this knife would be a shame. It’s a solid design that has been nicely executed with good blade steel.

In many ways I prefer the Patriot over the Delica: better blade steel, stronger lockup, and nicer ergonomics. But the Delica is an icon, and I prefer the blade shape and thumb hole on that knife.

Here is a shot of it next to a Spyderco Sage 1:

Still, I can’t help but wonder how the annals of knife history would look if this Patriot was released at the same time as the Delica. Would it be as widely recognized? Who is to say. I think it would have more than 5 reviews on Amazon – that’s for sure!

Will the Patriot blow your skirt up like a $400 titanium framelock flipper? Probably not, but this is a knife you can use guilt free on a daily basis. It is easy to carry and does a good job cutting stuff. You won’t cry if it gets scratched up by your keys and loose change.

It’s an excellent daily carry tool and I’ve enjoyed having mine at the ready for several months. I’ll probably bring it back to my office after I’m done with this review. It’s perfect for mail, packages, and anything else I need it to do. Recommended.

Boker Plus USA Folding Knife Steel Blade with Orange Handle, 3.38"

Fiberglass reinforced vibrant orange nylon handle
Premium 154CM steel blade
Includes reversible pocket clip and lanyard hole
Blade length: 3-3/8 in. Overall Length: 7-1/2 in. Weight: 2.1 oz.
Limited Lifetime Warranty

I recommend purchasing the Boker Patriot at BladeHQ or Amazon. Thanks for reading.

Kizer Feist Review

by Grayson Parker 1 Comment

Last Updated: July 13, 2019
The Kizer Feist is a knife that I’ve wanted to check out since seeing it in the 2017 catalog. At first, I almost missed it: it’s seemingly such a plain design that my eyes slid right over its page, and it was only during a follow-up perusal that I noticed it was a front flipper. Internally, that changed the design from “plain” to “minimalist.” Maybe a silly distinction on my part, but that was the train of thought.

Buy the Kizer Feist at BladeHQ

No products found.

Unfortunately, the first run of Feists had issues. Some customers complained of gritty actions and stiff lockbars, so Kizer put a hold on production until they could fix those issues in the now-released second run (with the help of the designer, Justin Lundquist). Between the risks of buying a first generation model and the speed with which the second run sold out, I never had a chance to pick one up.

Luckily, someone offered to trade me their Feist a few months back, and I’ve been carrying it frequently ever since. Incidentally, that person is Tony Sculimbrene of Everyday Commentary. His review of the Feist was published back in September 2017, and I recommend checking it out. This is a rare occasion where two people review not only the same design, but the exact same knife. [This happens to be a high quality unit from the first production run, for the record]. On the whole we’ve come to similar conclusions, though I think I’m a bit more taken with the Feist than he is.

General Dimensions and Blade Details

The Kizer Feist is a relatively small knife. It features a 2.875” blade housed in a 3.625” handle, and measures in at 6.55” overall. At 2.68 ounces it’s also pretty light. Numbers never tell the whole story, but I’m impressed by the size of the blade they manage to fit into the handle. The attention to detail is similarly impressive: the blade is perfectly centered, has a rounded spine, a curved plunge line, and a very attractive stonewashed finish. It also bears mentioning that the sub-3” blade of the Feist is legal to carry in a wide array of jurisdictions.

In addition to falling into my favorite size range, the Feist also features one of my favorite blade shapes. The modified drop point (especially this iteration of it) is far and away the most useful profile I’ve encountered for everyday tasks. It is comparable to the blade of the Viper Dan 2, or (if that’s too esoteric a reference) an ordinary paring knife. There’s enough belly to handle a picnic lunch, but not so much that the blade will slide out of prolonged cuts in, say, cardboard.

I have to admit that after reviewing the Alter Ego I was more than a little concerned about how the Feist would be ground. I needn’t have worried. Not only does the Feist have thinner stock (.12” thick as opposed to .14”), but the dished grind nearly reaches the spine of the blade, making for a much keener knife overall. As the picture below suggests, it didn’t cut the apples as cleanly as a paring knife, but it didn’t split them, either. It’s not perfectly ground – there’s a hair of wobble along the plunge grind – but that’s a fairly minor detail, and it doesn’t impact the cutting performance.

Crucible’s S35VN is a common choice for Kizer, so I wasn’t surprised to see them implement it on the Feist. That’s not to say it’s a bad choice, mind: S35VN is well regarded for its edge retention, rust resistance, and general toughness, especially compared to its predecessor S30V. I’ve sharpened the Feist once in two months, and truth be told it didn’t need it, I just wanted to polish it up a little. As always, regular stropping is recommended.

Handle, Ergonomics, and Pocket Clip

Simplicity is a wonderful thing. There is nothing extraneous to the Feist’s handle: no scallops, no inexplicable bumps or angles, just plain, contoured titanium. The only concession to vanity is a decorative pivot screw, but even that can be turned with an ordinary torx driver. Flaws would stand out on a design as simple as this, yet the handles are symmetrical, clean, and blemish free. The matte finish Kizer put on the Feist adds a bit of grip and contributes to the spare design language.

The themes that make the Feist’s handle visually appealing also make it incredibly practical. There is not a single line that forces the user to hold it in a particular fashion. Combine that, the excellent contouring, and a balance point just shy of the overtravel stop and you get a remarkably deft and responsive knife. There is no flipper tab, finger choil, or jimping that will stop your fingers from sliding onto the blade though, so be careful.

The Feist features a milled titanium pocket clip that’s mounted for tip-up, right-side carry. Unfortunately, that’s the only position to attach a pocket clip unless you want to modify the Feist or find someone who can. It’s fine as far as milled clips are concerned. The edges on it are buffed enough that it doesn’t generate a hot spot, and it has some (though not much) spring tension. Stowing and retrieving the Feist wasn’t an issue in jeans, work pants, or gym shorts, but for some reason I needed to use both hands to clip it to the pocket of my slacks. I honestly couldn’t tell you why.

Once stowed, the Feist is an excellent pocket companion. It’s lightweight, slim, fairly short, and has contoured scales to boot. There’s enough tension in the clip that it doesn’t shift in the pocket, regardless of what pants I wear. The clip leaves just under half of an inch of the handle exposed. An over the top style clip wouldn’t be unwelcome, but I’ve found the Feist discreet enough for my needs.

Deployment and Lock-Up

One of the reasons I really wanted to check out the Feist was because of its deployment method: the front flipper. Unlike traditional flipper knives (part of my brain is screaming as I type that), front flippers don’t have a tab that’s pulled to deploy the blade. Instead, the rear tang of the blade is elongated and machined to add a bit of grip, which in turn gives the user’s thumb enough purchase to pop the blade open. It’s a very elegant choice, and eliminates problems like accumulating gunk and snagging threads that other deployment methods are subject to.

Unfortunately, this new flipping has a learning curve to it, and Kizer’s execution of the front flipper was less than perfect. Many customers complained of gritty actions, which made opening and closing the knife more difficult. Apparently (and this is secondhand knowledge, so take care) the internal stop pin wasn’t press fit but left free floating, and that was responsible for the grit. If you own a first generation Feist, don’t worry: Kizer is running a redemption program where you can exchange it for an updated model. My review sample hasn’t exhibited this problem: the pivot is reasonably smooth, the detent is crisp, and deployment is easy, though there is a trick to it. Instead of trying (and failing) to describe how to use a front flipper, here’s a video that may help:

Once deployed, the Feist’s blade is held in place by a titanium frame lock. This particular lock features a stainless steel lock face, an inclusion that should be the industry standard by now. Not only do they reduce the need for maintenance, they also make it easier to service the knife, and thus prolong the life of the tool. Furthermore, it’s easy to incorporate a hidden overtravel stop into these inserts, which is exactly what Kizer did.

The lock’s performance has been excellent in the two months and change that it’s been in my possession. There is no blade play, no lock rock, and it consistently engages around 40% of the blade tang. Thanks to some careful machine work from Kizer, there’s enough room for my thumb to access the lock, and the internal edges are chamfered for comfort. Some users have reported overly stiff locks, but this seems to be limited to models from the first run. As before, mine has no problems.

Kizer Feist Review – Final Thoughts

Overall, I’m very impressed by the Feist. It’s a practical, elegant design that matches my needs perfectly, whether I’m in the field, the office, or enjoying a day off. That its debut was marred by reports of shoddy manufacturing is a shame, but by all accounts the second run has none of the problems of the first. The only cross-generational complaint is that the milled clip is a bit stiff, but that’s far from a dealbreaker, at least for me.

Unless you find a sale, the Feist costs around $170. That price bracket has some pretty stiff competition, including the Benchmade G-10 Griptilians, the Spyderco S110V Paramilitary 2, and the Zero Tolerance 0450. I wouldn’t turn my nose up at any of those, but for my money I’d rather have the Feist. Its unique, refreshing, and hopefully a sign of more to come from designer Justin Lundquist.

There are a few people that may want to steer clear of the Feist. Firefighters, EMS workers, law enforcement, and military personnel might find that the design is ill-suited to their needs. The design cues that make the Feist a fantastic everyday carry knife also make it a less than ideal rescue or ‘tactical’ knife. However, if – like me – your needs are fairly simple, and you’re just looking for a pocketable, elegant cutting tool, I think you’ll be more than happy with the Kizer Feist.

Next up: the Prometheus Lights Beta QR V2 in brass.

Kizer Feist – From $168.00
From: BladeHQ

Editor: I recommend buying the Kizer Feist at BladeHQ or Amazon. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Microtech Sigil MK6 Review

by Dan Jackson 7 Comments

There is depth to the knife industry. So much depth that a reviewer can review knives for 5 years, hire on 3 other writers to review knives, amass a catalog of over 300 knife reviews, and still not review knives from all the major manufacturers. That’s case with this website and Microtech at least. It’s almost shameful that we haven’t reviewed anything by Microtech yet. Thankfully, that gets remedied today.

Buy the Microtech Sigil at BladeHQ

Microtech is a medium sized knife manufacturer located in Bradford, PA. The company was founded in Vero Beach, FL in 1994, by Anthony Marfione, but then moved to Pennsylvania a decade later. As a Florida boy I have no idea why they would pack up and move to PA after 10 years. Usually it’s the other way around. There must be a lot of steel up in PA.

Microtech is known for their automatic knives, and their aggressive designs. Maybe that’s why it took me so long to buy one. I’m not a huge fan of autos, believing that a good manual folder can be almost as easy to operate, and less likely to draw the ire of law enforcement. Plus, their styling is the equivalent of Affliction shirts for the cutlery industry. Shockingly, a Microtech was the 3rd knife Jim Skelton ever reviewed. And it was from the “Zombie Tech” series at that. There is a lid for every pot.

Aesthetic preferences aside, the blades are also pricey. Not that price has stopped me from reviewing a knife in the past. I just gotta get a good deal on it, or really want to check out the knife. Plus the recent ugliness with the Tony S. lawsuit didn’t rev me up about the company either. I have wanted to check their knives out, but something else always took priority.

That all changed when I picked up this Sigil MK6. What a cool knife. This Sigil is beautifully built and richly detailed. Whoever designed it clearly had a lot of fun. My version is the “Apocalyptic” flavor, with a full stonewash and copper accent piece. Lets dive in.

General Dimensions and Blade Details

The Sigil has an overall length of 8.75″, a 3.75″ blade, weighs 5.2 ounces, and is made in the USA. This is a sizable knife. It’s a bit more than I typically like to EDC, but it provides plenty of canvas. Microtech took advantage of this and covered every inch in ornamentation.

The floor to ceiling stonewash lends the knife an aged appearance, although my blade is date stamped “02/2017”.

The blade is a long, sloping, modified drop point. The tip is dropped low, and you only get a slight amount of belly. The tip is also fine and delicate. The blade shape and thumb cutout resembles a prehistoric bird.

A lot of attention went into this blade, and the machining is top notch. The thumb hole has a series of steps milled around it. The finger choil is delicately chamferred. The flipper area has been pocketed. The grinds are beautiful and even. The edge has been uniformly applied. No detail has been overlooked on this blade.

And the blade is made of M390 stainless steel. M390 is about as good as it gets in blade steel, exhibiting the enviable combination of high edge retention paired with easy sharpening. Most super steels are a bear to sharpen, but M390 isn’t bad. It’s one of my favorite blade steels and Microtech gives you almost 4 inches of it here with their Sigil.

Cutting performance is pretty good. The stock on this knife is relatively thick, and the partial flat grind has its geometric limits. Still I had no problem breaking down boxes, opening mail, and cutting fruit. The M390 held up like a champ.

Handle, Ergonomics, and Pocket Clip

The handle is a celebration of milling, and a thing of technical beauty. Microtech is a highly skilled manufacturer, and that comes out clearly in the handle of the Sigil. The titanium handle slabs have been meticulously tooled from all angles, to the point where this knife could pass for an extra on the Dark Crystal.

You can become lost in the complexity of the Sigil. The insides have been pocketed out to lighten the knife. There is also extra fine milling for the frame lock release, the hardware for the pocket clip is hidden, a full titanium floating backspacer, and a copper pivot shroud doubles as a lock bar stabilizer. Microtech’s trademark proprietary hardware holds it all together.

Speaking of the proprietary hardware, although a lot of people aren’t a fan of non-standard hardware, I think it adds something to the overall effect of the knife. It’s totally different and helps make the Sigil feel special. That said, it would have been great if they included a tool. Actually came loose a couple times. Keep in mind I got this knife gently used, so this isn’t a comment on how it came from the factory. I was able to tighten everything down with my finger nail, but this is far from ideal. Thankfully the pivot feels snug and I haven’t had to mess with it yet.

The simple handle shape and heavy chamferring of the titanium handle makes the Sigil a comfortable knife in hand. That should come as no surprise give how large this knife is. There is a small forward finger choil giving you extra options, but I find it to be a little tight relative to other knives with finger choils that I own. I’ve used it, but would advise against getting too aggressive with this finger choil. Good jimping is found on the thumb ramp, flipper tab, and backspacer. Although it lacks corrugated G-10, this isn’t a slippery knife by any means.

The pocket clip is made of milled titanium. Milled clips have done a bit of an 180 over the past few years. When they originally came out they were the bee’s knees. Then they sort of fell out of favor when people found them to be less effective than traditional stamped steel clips. I still like a milled clip if it’s done right.

I’d say the clip on this Sigil is pretty good. It is snug up against the handle and has some spring tension. It’s not crazy spring tension, and I wouldn’t recommend jumping out of an airplane with the Sigil clipped to your pocket, but there is spring tension and the knife is held in place in your pocket. The hidden hardware aspect of it is awesome, and the machining is top notch.

The Sigil carries about how I would expect. It’s a large full titanium folder. Not a total boat anchor, but you feel its presence in your pocket.

Deployment and Lockup

The Sigil is a flipper on bearings. Flipping action is excellent. The generously jimped flipper, strong detent, and smooth bearing system scores the action of this knife a solid “8” on my somewhat arbitrary 1-10 scale for flippers. Better than average, but not a rocket launcher. In addition to the flipper there is an elongated thumb hole. It’s fully functional and you can open up the blade with the thumb hole if you want to be more subtle.

For lockup we have a titanium framelock with stainless steel lockbar insert. The engineering wizards at Miroctech did a fine job designing this frame lock. It is totally secure, with no blade play to speak of, yet the lock is easy to disengage. This is thanks to good lock geometry, and excellent milling on the portion of the lockbar where your thumb goes to release the lock.

As I mentioned previously, there is a copper pivot collar that doubles as a lock bar stabilizer. A nice touch and the only splash of color on an otherwise grey knife.

Here is a shot of the Sigil next to my Paramilitary 2:

It’s a little longer than the Para 2, but you get a lot more blade. Speaking of which, blade centering is perfect on my knife.

Microtech Sigil MK6 Review – Final Thoughts

The Sigil is an impressive knife. Microtech’s styling may not be to everyone’s taste, and this is a bigger knife, but you can’t argue that the Sigil has been beautifully executed with top shelf materials.

Almost every bell and whistle you could ask for is included. A milled clip, milled out handles, floating back spacer, hidden hardware, top shelf blade steel, and tons of machining. Fit and finish is outstanding. And this knife is made in the USA.

My only gripe is that the body screws come loose and they don’t supply the tool to tighten them.

This isn’t an inexpensive knife, but for just under $400 I think you get what you pay for. It’s almost on par with my old Shirogorov 95t, and that knife clocks in at 200%+ of the cost. Any interesting comparison is with a Sebenza.

While this is far from being an everyman’s EDC, I think those whose interests are piqued by the concept of the Sigil will be happy with this knife. It exceeded my expectations, and it makes me want to review more Microtechs in the future. Speaking of which, I really like the Sebastian Benja designed Stitch. I think that will be my next acquisition.

I know the Sigil is not a knife for everyone, so I won’t give it a blanket endorsement. But I give it 2 thumbs up if you are already in the market for this knife.

Microtech Sigil – From $390.00
From: BladeHQ

I recommend purchasing the Microtech Sigil at BladeHQ. Please consider that buying anything through any of the links on this website (including Amazon) helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Hogue X5 Review

by Dan Jackson 2 Comments

Last Updated: August 5, 2019
The button lock flipper is an intriguing concept. The fun of a flipper paired with a sturdy button lock sounds great in theory. We have reviewed a couple, namely the Spartan Pallas and Freeman 451. Ben reviewed the Freeman, and he reported that the flipping action was good, but the flipper on my Pallas left a lot to be desired. That’s because no one has been able to recreate the ball detent action that you find on a liner lock or frame lock knife that puts the “flip” into a flipper. That is, until Hogue released their X5 flipper.

Buy the Hogue X5 at BladeHQ

Buy on Amazon

Designed by Allen Elishewitz, and modeled after his Black Dolphin custom offering, the X-5 is a button lock flipper that has flipping action that will rival any framelock flipper. In fact, the action is so good you may mistake the X5 for an assisted opening knife.

When I first saw the X5, it was the wharncliffe version. I don’t mind wharncliffe knives, but this one was a little too odd for me to want to buy. The spearpoint version reviewed here has beautiful symmetry. I picked one up as soon as I could find a nice deal on one.

General Dimensions and Blade Details

The X-5 comes in 2 sizes: a larger knife with a 4″ blade, and a smaller version with a 3.5″ blade. I opted for the 3.5″ version, which has an overall length of 8.25″, and a weight of 4.62 ounces. The X-5 is made in the USA. I’d like to mention that this knife is beautifully made just like all the other Hogue knives I have reviewed. The fit and finish is immaculate, complete with a mirror polished edge. From a manufacturing standpoint this is a top shelf knife.

I like the look of this spear point blade. The harpoon knives the knife some attitude, and it compliments the shape of the handle. Allen Elishewitz is among the best knife designers I have met, and this X-5 puts his talents on full display. At any rate, the blade features a simple high flat grind, a neat swedge and a fine tip. There is a slight amount of belly. Nothing crazy, but the edge is one continuous curve. This blade has been given a matte black Cerakote finish. They offer this knife without the coating if you prefer uncoated blades.

Once again, Hogue selected CPM154 as blade steel for this knife. That’s the same steel they have in all their folders, so at this point I have plenty of experience with CPM154, and Hogue’s version / heat treat in particular. This is a great steel that provides easy sharpening and good edge retention. I’ve had some issues with 154CM staining in the past, but obviously this coated blade is not going to rust at all.

In practice the X-5 cuts nicely. I had no problems breaking down boxes, opening mail, and using the X-5 for other EDC related tasks. The tip is servicable, the belly is nice, and the grind is thin enough to cut things. The knife came with a beautiful edge which I have maintained through regular stropping. The Cerakote has also held up OK. It will burnish and wear with use (you can see some of that wear on my EX-04 below). As far as coatings go it’s pretty robust but not as good as DLC. Overall I have no complaints regarding the performance of this blade.

Handle, Ergonomics, and Pocket Clip

The X-5 handle is made of 2 pieces of hard anodized aluminum with textured G-10 inlays. Again, the handles here are beautifully machined. I would not be surprised if Hogue won Blade Show’s manufacturing quality award one year. Details include a vented spine, custom pivot and hardware, an integrated lanyard hole, and body screws on only one side of the knife. Everything oozes quality and attention to detail.

The handle on the 3.5″ version of the knife feels a little cramped. I can get a full 4 finger grip on the knife, but it feels like my pinky is going to slide off the back. Adding to things is the inclusion of an aggressive finger choil that limits your hand placement options. This is probably my biggest gripe with the knife. That said, the handle certainly works and I’m sure the 4″ version will be more accommodating to larger hands. Part of what I enjoy about this knife is the unique aesthetic, and I’m willing to sacrifice a little for the sake of this unique design. However, this is coming from a guy with a 100 pocket knives. If this was my only EDC knife I’d want something with milder ergonomics.

The pocket clip is a deep carry affair, blacked out and swappable for ambidextrous tip up carry. Retention is extremely tight. Pants shredding tight. There is no way this thing will fall out of your pocket, but that’s provided you can actually get this ting into your pocket in the first place. I find the spring action of the clip to be too tight. I’m also not a huge fan of the large tip of the pocket clip that is exposed when this knife is clipped into your pocket. It will scrape car doors if you aren’t careful. I know folks have been critical of the large spoon clip in the EX series, but I think I prefer it over the clip on this X-5.

The X-5 is light for its size and carries easily enough. The nice thing about a matte black deep carry clip is that it makes for a discrete knife. This 3.5″ version is an easy EDC for me, but I would like to see this pocket clip tweaked a little bit.

Deployment and Lockup

The X-5 is a flipper. That should be pretty obvious. There are no thumb studs, thumb holes, or secondary means of opening the blade. That’s alright because the flipping action is outstanding. Like I mentioned in the introduction, the button lock flippers I’ve handled in the past haven’t flipped well. That’s because they never were able to recreate the detent action of a linerlock or frame lock flipper. The X-5 does that by embedding a ball detent into the handle. This YouTube video does an excellent job showing you what is going on. A ball detent is set into a stainless steel spring inset in the handle, and there is a hole and track on the blade for the detent to run in.

The end result is fantastic flipping action – to the point where you may mistake this for an assisted opening knife. But it’s not an assisted opener, and one way you can tell is by depressing the button lock: the blade swings freely. It’s also worth noting that there are no stand alone washers on this knife. Instead, the washers are milled into the aluminum handles. The end result is buttery smooth.

The button lock has been beautifully executed. There is no stick at all in my lock, and lockup is tight as a drum. There is an external safety. Typically I’m not a fan of these, but Hogue has dialed this in so the action of the safety is crisp and purposeful. Unlike most knives with secondary safeties, it doesn’t flop around, and you aren’t going to accidentally activate it on the X-5. While I don’t use it, I like how they did it.

Centering is dead nuts perfect.

Hogue X5 Review – Final Thoughts

All said I’m a fan of the X-5. Hogue makes a beautiful knife, and the X-5 may be the nicest model I’ve handled yet. And they have cracked the code for a button lock flipper. The flipping action is flipping outstanding. That alone earns some points in my book, and I hope Hogue applies this technology to other knives, or licenses it to other companies. I also happen to be a fan of this design. I find it visually appealing and the execution is top notch. For these reasons I appreciate and enjoy the X-5 as a knife collector.

That said, there are a couple issues with the knife that prevent me from giving it a perfect score (not that I really score anything on here anyways). First, the handle is cramped. This knife is not going to replace my Griptilian or other work knives any time soon. I could have gotten the 4″ version, but I usually don’t like to carry folding knives that large. Second, the pocket clip is too tight, and the tip of the clip pokes out too much. It shreds your pockets, is a chore to use, and the tip sticks out to the point where it can inadvertently scrape up cars if you aren’t careful. As a fan of the design, the ergonomic issues are forgivable, but I still think the pocket clip needs work.

So this isn’t a perfect knife, but for me the pros outweigh the cons. I have plenty of plain Jane pocket knives, but nothing else like the X-5 in my collection.

If you are looking for one Hogue knife to use as your EDC, I’d recommend the EX-01 or EX-04. They are more practical and more comfortable work knives.

But if the X5 speaks to you as a collector and enthusiast, then I’m here to tell you to answer the call. It’s mostly an awesome knife. Not my desert island EDC, but there is a lot to enjoy with this one. And like the EX-04, I don’t see myself offloading my X-5 any time soon.

HOGUE X5 3.5" Spear Pants Black Frame Stock Accessories

Great Product

I recommend purchasing the Hogue X5 at BladeHQ or Amazon. Thanks for checking out my review.