Made in the USA

Spyderco Manix 2 Lightweight Review

One of the biggest events of the year for knife nuts is Blade Show. Put on by Blade Magazine, this industry wide convention draws a cavalcade of steel-toting enthusiasts to Atlanta, Georgia, where custom knives are fought over and new production designs are revealed. For the last several years, their Overall Knife of the Year award has been granted to blades that are…let’s say, of questionable utility. Beautiful, and without a doubt technical marvels, but they bear more resemblance to concept cars than to utility vehicles. To find designs that are within the reach of the hoi polloi, one should look at some of the more obscure awards, which focus on budget, innovation, and place of origin.

Buy the Manix 2 LW at BladeHQ

Buy on Amazon

This review focuses on one such design: the Spyderco Manix 2 Lightweight, which won the 2010 Blade Show award for Most Innovative American Design and has since garnered quite a bit of critical praise. Nowadays, the Manix is seen as part of the vanilla Spyderco line, but that’s not how it’s always been. At the time, it seemed like the Manix was the way of the future. Thin, fully flat ground blade? Check. Thumb hole? Check. Innovative lock that kept your fingers clear of the blade? Also, check. That all of these features are found at a pretty economical price point and on a blade that’s made in the U.S.A. is impressive today, but was a much bigger deal when the question of the day was Benchmade vs. Spyderco.

General Dimensions and Blade Details

The Spyderco Manix 2LW measures just over 8” overall, with a 3.37” blade and a 4.66” handle. The Manix 2 LW is made in the USA. As its name would imply, the Manix 2LW doesn’t weigh much – only 2.9 oz. – a weight that’s pretty remarkable for a knife this size. It’s worth mentioning that the cutting edge is actually 2.88” because of the inclusion of a 50/50 finger choil. I applaud that decision. Spyderco is famous for their ergonomics, and the finger choil is part of that recipe.

Spyderco chose Carpenter’s BD1, a relatively unknown steel, for the lightweight version of the Manix 2. According to the data sheets, BD1’s performance should be the equivalent of high quality 440c. Most online feedback indicates the same. In my experience, it’s been difficult getting the BD1 as sharp as I’d like. Its edge retention isn’t the best, and requires regular maintenance. If there is one attribute it excels at, it is corrosion resistance. I’ve forgotten to clean this knife after cutting citrus before, but even that didn’t leave so much as a mark.

For all the questions about the blade steel, Spyderco hit it out of the park with the blade shape (and grind). The leaf-shaped blade is a mainstay in their product line and never disappoints. When paired with a full flat grind and fairly thin stock (.125”), you’re almost guaranteed success. Extensive use in the kitchen and the field bears that assumption out. My sharpening issues aside, the blade performs very well. The smokey mirror finish Spyderco put on the Manix is easy to clean and doesn’t attract fingerprints like a higher polish would.

Handle, Ergonomics, and Carry

The handle on the Manix 2 Lightweight is made of fiberglass reinforced co-polymer, or FRCP. It is very similar to the fiberglass reinforced nylon (FRN) Spyderco uses on the Delica/Endura/etc. When compared side by side, FRCP is stiff, while FRN has a bit of give to it (akin to rubber). I own knives with both as handle materials, and I don’t know if I have a preference. As with any plastic handle, there will be folks who complain about the material feeling cheap, but I don’t mind it. I prefer the translucent blue handle over the black handle. This knife is very well-suited to backpacking, and a bright handle helps ensure that your knife doesn’t get lost among the foliage.

I’ve found the ergonomics to be just as good as I’d expect from an in-house Spyderco design (read: excellent). Some folks complain that the handles are too blocky. Those people need to find something else to complain about, because I could not find a fault with the ergonomics. The 50/50 finger choil allows the user to choke up for better push cuts, while the rear grip is well-suited for slicing and draw cuts. Spyderco’s bi-directional grip pattern is very effective at gluing your palm to the handle without being abrasive. I will say I could do without the jimping on the interior of the handle.

Spyderco’s wire clip seems to be pretty polarizing, at least if you take online comments seriously. Some love it because it’s discrete, doesn’t generate a hotspot, and doesn’t shred the edges of your pocket. Those who hate it complain that the wire clip wiggles around and doesn’t offer enough tension to keep the blade secure in the pocket. I’m in the former camp; every wire clip I’ve handled has had plenty of tension, and I prefer the practical advantages outlined above. Between the low weight and excellent clip, this knife is a dream in the pocket (particularly for its size).

Deployment and Lock-up

I’ve mentioned this before, but the knife market is almost exclusively focused on flippers right now. Personally, I’ve always preferred the thumb hole as a deployment method. They’re just as easy to flick, but much better when it comes to slow-rolling the knife open. I also don’t wear my fingers out fidgeting with Spydercos the same way I do when I’m messing around with a flipper. This is a very nice execution of the thumb hole. At 14mm, it’s large enough that opening the knife is never a problem, even while wearing gloves. The interior of the cut out has been nicely polished and slightly chamfered.

If it wasn’t for the lock, I probably wouldn’t like this knife as much as I do. The Manix is equipped with the Caged Ball Bearing Lock, which is frequently compared to Benchmade’s Axis Lock and SOG’s Arc Lock. All three offer ambidextrous manipulation of the lock without putting your fingers in the path of the blade. Out of the three, the CBBL is my favorite. It fixes the one problem that I have with the other offerings: a weak detent. On the Manix, the detent is not only quite firm, but crisp as well. There’s a level of security knowing that the blade isn’t going to flop open with a wave of the hand.

Spyderco Manix 2 Lightweight Review – Final Thoughts

My thoughts on the Manix 2LW are generally positive. If it weren’t for my issues putting a keener edge on the BD1, I’d carry it more frequently than I do now. Even with that handicap, it’s a great knife. The Manix 2 LW is available at most retailers for around $80.00. If you’re worried about the steel (my experience seems to be an outlier), Spyderco also offers the Manix 2LW in CPM-S110V for around $35 more.

That aside, the Manix is arguably in an awkward spot on the product line. For a relatively small amount of money, you could instead purchase a Paramilitary 2, which is widely regarded as one of the best knives available (regardless of price point). This begs the question: budgetary concerns aside, is there a niche the Manix fills that the Paramilitary doesn’t? I think there is. As much as I love my Paramilitary 2, I think the Manix 2LW actually makes for a better outdoors knife. Specifically, for backpacking. The bright handle, low weight, and easily maintainable steel are all desirable qualities for a blade you can tote into the backcountry.

Whether you want a knife for the outdoors, or you’re looking for a bigger everyday carry blade, the Manix 2 Lightweight is sure to satisfy.

Spyderco Manix 2 Lightweight Signature Knife with 3.37" CTS BD1 Steel Blade and Translucent Blue FRCP Handle - PlainEdge - C101PBL2

Ready For Anything: The Manix 2 is an extremely capable full-sized folder that is known for it's strength and performance. Its broad blade provides exceptional cutting power, while its textured index finger choil and thumb ramp allow a forward grip.
Light and Durable: This Manix 2 handle is fabricated with Fiberglass Reinforced Co-Polymer. FRCP creates a tough, chemical and heat resistant handle that is extremely lightweight and Versatile.
Dependable: If you are looking for control and precision, look no more. This knife features our PlainEdge grind which is known for creating a smooth and exact cut.
Low Friction: This knife features a blade ground with flat bevels that extend from the spine all the way to the cutting edge. This grind reduces drag during cutting and decreases overall weight.
High-Strength Lock: The Ball Bearing Lock features a patented compressive lock that wedges a ball bearing between a fixed anvil and the blade tang. The mechanism also serves as a detent to hold the blade in the closed position.

I recommend purchasing the Spyderco Manix 2 LW at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade 15080-2 Crooked River Review

by Dan Jackson 33 Comments

Last Updated: July 19, 2019

It’s no secret that I think the creative team at Benchmade has been adrift for the past few years. This is perhaps best evidenced by the fact that the company’s most exciting new offerings are actually re-issues of old models: the 940-1 and 551-1. These rockstar designs are interspersed among more puzzling offerings like the 808 Loco and 300 Axis Flipper.

Buy the Benchmade Crooked River at BladeHQ

Buy on Amazon

But Benchmade does seem to be cobbling together a theme. They seem to be taking this “old school, meet new school” approach not only to their classic designs, but also by melding traditional designs with modern manufacturing in their “Hunt” lineup. I thought the Small Summit Lake was a successful mashup of traditional lockback folder with modern materials, beefy construction, and precision manufacturing. The 15080 Crooked River is a knife cut from that same cloth.

In fact, the Crooked River takes the juxtoposition even further. This is an even greater departure from tradition to the point where we almost have a caricature of the classic bowie. Yet there is still a timeless quality to the knife. The low slung blade and bolstered handles tug at the heartstrings of traditional knife design, while the finishes and flourishes appeal to this fan of modern folding knives.

General Dimensions and Blade Details

The Crooked River has an overall length of 9.3″, a 4″ blade, weighs 5.41 ounces, and is made in the USA. This is a big knife, and is far outside the confines of what I would consider to be an every day carry (EDC) piece. If you were to whip this out in public to trim packing tape or open an envelope, most people would hide under their desk. And if a friend offered up a Swiss Army Knife at a campsite, you could go full Crocodile Dundee on the guy with this Crooked River. This is a “knoife”. I wouldn’t mind a smaller, more manageable version for daily carry.

The Crooked River features a long and lean clip point blade. I have always enjoyed a good clip point for it’s practicality, and the Crooked River is no exception. The high flat grind has been nicely executed complete with Benchmade’s 2-tone stonewashed satin finish. The blade is cut from an impressive 3.15mm thick piece of S30V stainless steel, and it carries a significant amount of steel out all the way to the tip. The end result is a blade that has a good tip for piercing, plenty of edge for cutting, and a nice belly for food prep and possibly even skinning.

The choice of S30V stainless steel for the blade is less exciting now then it may have been 5 years ago. These days I prefer S35VN for it’s improved toughness and ease of sharpening over S30V, but in my opinion Benchmade has always done a great job with their S30V. For example, the S30V on the Volli continues to impress me with it’s sharpness, edge holding, and ease of maintenance. I think Benchmade knows how to make the most of this steel.

The blade geometry of the Crooked River is stouter than the Volli, but this is still a functional blade and the S30V performs nicely on this knife. Capable of taking a keen edge, and holding it for an acceptable period of time, the S30V on the Crooked River is still functional despite there being sexier steels on the market. No issues with corrosion either.

Handle, Ergonomics, and Pocket Clip

The Crooked River has a long curving handle that compliments its long curving blade. The combination of diamond wood, aluminum bolsters, and orange pivot collar is striking, and I am sure that decision alone has sold many 15080-2’s for Benchmade. If resin-injected wood isn’t your thing, then Benchmade also offers the Crooked River with smooth gray G10 handle scales.

Underneath the scales are full stainless steel liners (skeletonized) and a bright orange G-10 backspacer. Holding things together is a large black pivot and blackened steel hardware. Everything is precision fit, and there are a number of nice details to enjoy, like the arced face between handle scale and bolster, the geared backspacer, and of course the snazzy orange pivot collar. Even the lanyard hole is oval and chamfered, adding style to an otherwise mundane feature of a knife.

Despite there being a good deal of weight around the pivot, the balance point on the Crooked River is behind the axis lock, and is close to the “hump” of the finger choil. The hand feels most at home here; set back further on the knife. While this isn’t billed as a tactical folder, I would be curious to get someone like Chad’s take on the Crooked River. I have no doubt that a knife like this could be pressed beyond pure utilitarian purposes if the need arose.

Beyond my comments on the balance of the knife, the Crooked River benefits from a subdued approach to ergonomics and traction. The long handle provides plenty of room, even for extra large hands. The diamond wood scales offers some texture (not much), while a mild run of jimping on the back of the handle indexes the thumb while still allowing the user to cut with the knife for extended periods without significant thumb fatigue. All said, the ergonomics have proven to be adequate for my purposes.

The Crooked River is a big knife. While I don’t think 5.41 ounces is overweight given the build quality and footprint, it’s still substantial, and when closed the knife is pivot heavy. This creates something of a pendulum effect in your pocket. Benchmade has tried to counter this with a stiff pocket clip. This is a good idea, and my Crooked River holds firmly in place.

On the subject of pocket clips, Benchmade went with a black parkerized version of their split arrow clip. I have always liked the split arrow clip, and here it is situated high on the handle for a relatively deep and discrete carry. The handle is also drilled and tapped for ambidextrous tip up use. That said, Benchmade’s deep carry clip will fit on this knife, and if you prefer a more discrete deep carry option Benchmade typically will send you a deep carry clip free of charge if you ask them nicely.

Deployment and Lockup

While some may grow bored with the axis lock, it remains one of my favorite locking mechanisms. I like the easy one handed opening and closing. Plus it’s fully ambidextrous. And I don’t know if I am simply bullshitting myself, but to me it looks like the phosphor bronze washers on these Benchmades have gotten thicker over the years. Much like my new 551-1, this Crooked River is smooth and easy to open. The blade pops into place with a satisfying “snick”, and the ambidextrous thumb studs are easy to get at with either hand.

Unlike some of the axis lock knives that have crossed my path, my Crooked River locks up tightly and without any play. Blade play is a common complaint on axis lock knives, but I have found that most knives can be fixed with a targeted application of Loctite. Here, blade play was a non-issue, and the axis lock remains as practical and easy to use as ever.

Benchmade Crooked River Review – Final Thoughts

Not to get all jingoistic on everyone, but the Crooked River appeals to the red blooded American in me. This knife takes me back to my childhood, handling my dad’s old Buck fixed blade tucked away his closet next to the well worn Swiss army knives, and old harmonicas.

There is an undeniable charm to the Crooked River that strikes at that primal note that has drawn many people to knife collecting in the first place. While not the most practical offering for an erudite urban EDC, the Crooked River is unapologetically bold and beautiful, and I think it is one of the nicer new designs from BM.

The Crooked River is a knife that I would like a smaller version of. As it stands I don’t see it getting a ton of use personally, but perhaps it has a place in your collection. If the Crooked River piques your interest in the same way that it piqued mine, then I am pleased to report that it is a well made and satisfying folder.

Benchmade - Crooked River 15080 EDC Knife with Wood Handle (15080-2)

BUILT FOR THE HUNT: Simplicity and style meets unmatched function, no matter the application; An ideal hunting knife capable of countless tasks in the field.
CPM-S30V STEEL: For first-rate edge retention and corrosion resistance; Clip-point construction for easily controlled cuts. Factory in Oregon City, Oregon.
STABILIZED WOOD HANDLE: Is made from a durable composite material that's been backfilled with resin; Stands up to a range of harsh elements and environments; Stronger than natural wood.
AXIS LOCKING MECHANISM: Ensures safety and a smooth open and easy close; Reversible split arrow clip; Lanyard hole for versatile carry options.

I recommend purchasing the Benchmade Crooked River at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade G10 Griptilian 551-1 Review

by Dan Jackson 29 Comments

I wasn’t one of those guys that had a big issue with the plastic handles on the original Griptilian. I always thought they were light and durable. Maybe not the sexiest choice of materials, but certainly practical. But for many the plastic handles of the Griptilian were a source of contention at best. At worst they were a deal breaker.

Buy the Benchmade G-10 Griptilian at BladeHQ

Buy on Amazon

So for the longest time if you wanted a Griptilian with G-10 handle scales, you had to go to the after market. This market was pioneered by ex-pat Kevin Wilkins. His line of WilkinsGRIP aftermarket scales were the enthusiast’s best choice if you wanted a G10 Griptilian.

Benchmade finally came around in late 2015 and released both the 551-1 Griptilian and 556-1 Mini Griptilian with G-10 handles. This is arguably the most exciting thing Benchmade has done since the 940-1 Osborne.

This knife was provided to me free of charge by the fine folks over at KnifeArt. In no way has this impacted my impressions of the 551-1. I think the people over at KnifeArt are good guys, I think they run a quality website, and I appreciate their letting me check out this 551-1. Now on to the review.

General Dimensions and Blade Details

The 551-1 has an overall length of 8.07″, a 3.45″ blade, weighs 4.17 ounces and is made in the USA. The G10 version is almost an ounce heavier than the original Griptilian, but it does not feel heavy for it’s size, and seems significantly lighter than my WilkinsGRIP equipped BM 552 / Ritter Griptilian.

The 551-1 has an identical drop point blade to the original Griptilian and is offered with your choice of thumb stud or thumb oval. I always preferred the look of the thumb stud version of the Griptilian, so that is what I got.

When I compare this blade to my original Griptilian the only difference I can detect is that the blade has been given a bit of a stonewash. Of course, the 551-1 features a new blade steel, and I will talk about that below. But beyond that you have the same excellent blade shape of the original Griptilian, with a saber flat grind, and swedge. This classic drop point shape has served me well for many years now.

Besides the switch to G-10 scales, the biggest news about the 551-1 is change to CPM-20CV blade steel. This is a steel that I was previously unfamiliar with. Manufactured by Crucible Industries, CPM-20CV is advertised as a steel with high corrosion resistance and wear resistance, and good toughness. Chemically it is similar to M390, which is an excellent steel. CPM-20CV has an extremely high chromium content, which results in its corrosion resistant qualities. From what I can gather, this appears to be a good choice for a folding knife. It may not have the toughness of a steel like 3V, but I think the extra corrosion resistance is a nice trade off here. My regular 154CM Griptilian has been through the ringer, and it occasionally shows small spots of rust if I forget to clean it.

My 551-1 came razor sharp from the factory, and this 20CV seems to hold an edge well. So far I have used the knife to break down a few boxes, open mail, etc. I haven’t wailed on this knife like my original Griptilian and so far have only needed to gently strop the knife to maintain its edge. No corrosion or complaints thus far, but I am not 100% convinced that this steel is worth the price premium over regular 154CM to me.

Still, it’s an interesting steel and I intend to keep this knife for long term testing and evaluation. I’ll update this review as I “gather more data points” and use the knife in the coming years. So far so good.

Handle, Ergonomics, and Pocket Clip

Obviously the handle is the main event here for the 551-1, and is basically the entire point of this knife. I am pleased to say that this new G10 handle has been beautifully executed. It is fully 3-D machined, and features bright blue liners and anodized blue backspacers beneath gray overlays. I am not sure if the gray-blue combo would have been my first choice, but the blue certainly “pops” here and my handle has been flawlessly executed. I am hoping Benchmade will roll out some other color combos in the future.

Like the original Griptilian the 551-1 features partial nested steel liners. That is about the only similarity with the handle construction of the original Griptilian. Even the hardware has been upgraded on the 551-1. This new handle is a totally different animal and it transforms the look and feel of the knife.

My favorite aspect of the new handle is how they shaped it to match the contours of the original Griptilian. If you handle aftermarket scales for a Griptilian, they are usually very big and boxy. These aftermarket handles change the ergonomics substantially and add additional weight. That is not the case for the 551-1. Here you get a feel in hand that is very faithful to the original FRN Grip. Of course there is a little extra weight, and the G-10 does feel slightly different, but the overall profile and hand filling nature of the original model has not been lost in translation. Benchmade did away with some of the extra texturing on the handle, and the diamond pattern here isn’t quite as grippy as on the original knife, but there is plenty of grip here for me and I’d go so far as to say that this is an improvement over the original knife from an ergonomics perspective.

Benchmade decided to include a deep carry pocket clip on the new 551-1 rather than their original spoon clip. I like this deep carry clip. It makes for a discrete knife that I have actually worn with slacks at work a few times now. This is a proven clip design. I think the 551-1 carries well for what it is. This is a larger knife, and it is heavier than it’s FRN predecessor, but this is still something that normal guys can carry and use and I think this is a viable EDC option (although admittedly the mini-551-1 is really all you will need for 99% of your EDC tasks).

Deployment and Lockup

Benchmade has equipped the 551-1 with an impressively beefy set of phosphor bronze washers. Because you have an open back design, the washers are very prominent on this knife. The blade flicks open effortlessly. This is a satisfying knife to open and close. Whether you decide on the thumb stud version or the thumb hole version I don’t think you will have a problem accessing the blade.

Of course for lock up you have an axis lock here. I have discussed the axis lock for years now. It remains one of my favorite locks as it is fully ambidextrous and allows you to easily open and close the knife with one hand. I find that the use of G10 handle scales adds a lot of structural rigidity to an axis lock knife and the 551-1 is no exception. It feels solid, and may inspire more confidence in the end user than FRN.

Blade centering is perfect on my knife, as I would expect from a nearly $200 folder.

Benchmade 551-1 Review – Final Thoughts

I must admit I was somewhat skeptical about this knife given the enormous price premium over the regular FRN verion, but the 551-1 has been beautifully executed, and I can see where the extra money went. They didn’t just slap some G10 on this thing and call it a day – every single facet of the original Griptilian has been re-considered and in someway upgraded. It’s clear Benchmade spent a lot of time and effort to dial in the 551-1.

Compared to its FRN predecessor, this new 551-1 is simply a superior tool. If the original FRN scales drove you up the wall, then the 551-1 cures that ill handily, and if you are a Griptilian fan I’d say this is basically a “must buy”. I was skeptical at first, especially given the price point, but the 551-1 has exceeded my expectations.

Benchmade - Griptilian 551-1 Knife, Drop-Point Blade, Plain Edge, Satin Finish, Gray Handle G10 Handle, Made in the USA

HIGH-QUALITY: The CPM-S30V stainless steel blade is extremely well-balanced, offering superb edge qualities and rust resistance. The glass-filled nylon handle is tough yet attractive, making it ideal for hard jobs and everyday carry.
WELL-DESIGNED: Benchmade's AXIS lock is exceptionally strong and fully ambidextrous. The Griptilian 551 is a manual knife that can be opened and closed single-handedly.
COMFORTABLE: The 551's lightweight design and handle grips make it comfortable to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Griptilian 551's drop-point utility blade style and all-around functionality make it ideal for everyday use, outdoor activities and even tactical applications.

I recommend buying the 551-1 at Amazon, or BladeHQ, KnifeArt.com. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

KA-BAR BK14 Becker Knife and Tool EsKabar Review

by Chad McBroom 3 Comments

During the 2016 SHOT Show, I had the great opportunity to meet a man named Ethan. Ethan was working at the KA-BAR Knives display and approached me as I was viewing some of KA-BAR’s newest designs. We began talking about knives and telling war stories, and before I knew it, almost an hour had passed. When I shook his hand to say goodbye, he handed me a nifty little knife to take with me. He also handed me his card, at which point I finally realized that I had been talking with Ethan Becker.

Buy the BK14 at BladeHQ

Buy on Amazon

Ethan Becker is a household name for many. His grandmother is Irma S. Rombauer, author of one of the United States’ most widely published cookbooks—Joy of Cooking. Ethan assumed authorship of this popular book from his mother in 1976, which is why his name is familiar to so many in the kitchen.

As an avid outdoor enthusiast who was in constant search for the perfect knife, Becker founded Becker Knife and Tool in the early 1980’s and began designing and manufacturing hard-use knives right out of his garage. His knives have always been highly regarded among knife experts and critics and in high demand amongst users. To attest to this is the fact that he won the 1990 Blade Award for Most Innovative American-Made Design. While the demand for BK&T Knives has far outgrown Becker’s garage, KA-BAR Knives continues to produce his best-selling designs.

General Dimensions and Blade Details

The knife that Ethan handed me during SHOT Show was the BK14 EsKabar, a hybrid collaboration between BK&T/KA-BAR and ESEE Knives. This unique little neck knife (which KA-BAR allowed one of its customers to name) features the blade design from the BK&T/KA-BAR Becker Necker and the handle design from the ESEE Izula. Made in the USA from 1095 Cro-Van steel, this seven-inch long lightweight knife, featuring a drop-point blade makes for a highly functional everyday/survival knife.

Of course, those familiar with the ESEE Izula will want to know how these two knives compare with each other. To answer that question, the dimensions of the EsKabar and the Izula are identical from the handle, which measure 3.75” long. The EsKabar incorporates the large quillon from the Becker Necker, as well as the larger Necker blade. The blade on the EsKabar measures 3.25” as opposed to the 2.63” blade on the Izula. The EsKabar also has a larger belly than the Izula. The difference in thickness is only 1/100th of an inch with the EsKabar being the thicker knife at 0.165”.

For those who may be wondering what the difference is between 1095 and 1095 Cro-Van, 1095CV is essentially the same chemical composition as 1095 with the addition of small amounts of Chromium and Vanadium for better hardening and bonding (hence the term “Cro-Van”) and smaller amounts of Nickel and Moly for added toughness and edge holding. The actual AISI name for this steel is 50-100B. KA-BAR has been using 1095CV for years, even though there was a period where they actually listed it as 1095 in their literature.

Handle and Ergonomics

As I mentioned previously, the EsKabar handle is identical in every way to the ESEE Izula with the exception of the 1/100” difference in thickness. The skeletonized handle has a good feel to it, but gets even better when you wrap the handle with 550 cord. The handle has a nice angle to it, which offers some excellent cutting ergonomics. It is a simple, yet functional design.

Editor’s note – you can also purchase OEM scales from ESEE for the EsKabar. I imagine they make the knife feel real similar to my Izula II (excellent).

Sheath

The EsKabar comes with a MOLLE compatible, injection-molded plastic sheath that can be worn around the neck or lashed to gear using the accompanying 550 cord. It is also cut to fit the KA-BAR TDI metal belt clip, which is available from KA-BAR for $10.35. The sheath comes equipped with a safety lock to ensure that you don’t lose your knife when things get rough. This feature can be removed if you prefer a more streamlined setup.

Personally, I found that I prefer to carry the EsKabar as a neck knife using a 550 cord lanyard. When wearing a neck knife is too cumbersome or inconvenient, then I simply create a belt loop on the sheath by running a piece of 550 cord vertically through two rivets on the inside of each side of the sheath and crossing the cord on the outside in the same fashion as one would lace up a shoe. This creates a nice belt loop attachment that does not add any extra bulk to the sheath. If you use a cord lock to secure the cord rather than a knot, then you have the added option of a convenient quick release.

I also prefer to remove the safety lock from the sheath. It adds some unnecessary bulk to what is otherwise a nicely streamlined system. The knife locks so securely into the sheath that most people will find the presence of the lock unnecessary unless going into the harshest of environments.

BK&T / KA-BAR BK14 EsKabar Review – Final Thoughts

I was very pleased with the quality and design of the EsKabar. I love to see knife-makers work together on projects such as this one. One of the things that I have always appreciated about the knife industry is that there is such a level of camaraderie and appreciation for each other’s work. Knife makers understand the blood, sweat, and tears that go into transforming a chunk of steel into a functional work of art. The joint effort between BK&T, KA-BAR, and ESEE that resulted in the EsKabar is a testament to the benefits of such companies working together to reach a common goal.

If you are looking for an economically priced, fixed-blade survival knife, then you can’t go wrong with the EsKabar. With a retail price of around $60.00, the EsKabar delivers high-end quality and functionality to a price point that most people can afford.

Sale

Ka-Bar BK14 Becker Knife and Tool Eskabar Knife, Black, 7-Inch

Becker knife design with high quality 3 1/4" blade made from 1095 Cro-Van steel
Heavy-duty hard plastic sheath
Overall length of 7"
Made in the USA
Becker knife design with high quality 3 1/4" blade made from 1095 Cro-Van steel

I recommend purchasing the BK&T/KA-BAR EsKabar at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Gerber Applegate Fairbairn Covert Review

by Mike Teeples 5 Comments

The first knife I ever owned, even before my Swiss Army knife, was a Gerber that my Dad gave me. It awed me then and awes me now, and is being passed down within my family; hopefully for generations to come. When a couple of military buddies mentioned the Gerber Applegate Fairbair Covert to me as a “must have” for my collection, the were sure to mention the rich history of knife’s designers.

Buy the Gerber Covert at BladeHQ

Buy on Amazon

I’m not crazy about tricking out a knife with logos and what not, but if you’re going that route they may as well be the signatures of some pretty accomplished dudes. Mission accomplished with the Covert. Both Colonel Rex Applegate and William E. Fairbairn were pioneers in close quarters armed and unarmed combat. Colonel Applegate was even inducted into the Blade Magazine Cutlery Hall of Fame at the 1994 Blade Show. Look them up some time and you are sure to be impressed by their accomplishments.

General Dimensions and Blade Details

The Covert has an overall length of 8.75″, a 3.75″ blade, weighs 4 ounces, and is made in the USA. A significant challenge in the tactical folder market seems to be balancing weight and size with concealability, and to do this without losing the knife’s function. The Covert walks that tightrope nicely. With a full 5” handle, it accommodates even large hands. One would think that would lead to a noticeable weight in your pocket, but the 4 ounces feels extremely light in hand and becomes an afterthought in the pocket in no time.

And if you are really size sensitive, Gerber also offers a Mini Covert with a 2.92 inch blade and weighing in at a mere 2.2 ounces.

The blade itself is .125” thick, and include signatures of its creators and “USA” proudly stamped under the Gerber logo. The spear point blade features a double bevel and serrations running halfway down the sharp side. The opposite edge could be sharpened to suit the owner. I’ve never been motivated to do so, but could see that being an option since this is a folding knife designed for hand-to-hand combat.

The Covert comes with a titanium nitride coated 154CM stainless steel blade, a nice departure from Gerber’s usual lineup of 420HC blades. 154CM is a great working steel that is reasonable to sharpen yet still good in the edge retention department. Seeing how this nice retails for close to $100, 154CM was an appropriate choice given the price.

Handle, Ergonomics, and Pocket Clip

The words “Glass Filled Nylon” (GFN) do not give justice to how the Covert feels in the hand. The material is dense and of high quality – it does not feel like “cheap plastic”. Many manufacturers use GFN and when you pick it up its clear why the choice is popular. GFN holds up well to abuse and can be molded into a near-infinite variety of shapes and textures. This one is ribbed for my pleasure, and bears a surface that’s easy to grip without catching on your favorite pair of jeans when removing it from the pocket.

The GFN itself is semi-smooth with the texture of a medium grit river rock and almost seems temperature neutral regardless of conditions. I know this knife isn’t going to slip out of my hand and don’t have to worry about blisters with extended use (as unlikely as extended tactical use is). About three quarters up the length of the handle you will find ambidextrous finger choils with mild jimping.

This knife was designed with combat use in mind, and the simple handle allows for the user to work with the covert in forward and reverse grips.

The finger notches provide an anchor point that give that extra bit off assurance and make for an overall high quality fit in the hand.

The clip falls short. It’s a decent size and sits in your pocket at about the right height, but allows for ambidextrous tip down carry only. Happy days for those of us that are tip down users. The rest of us will have to get over it or find another blade. One other point regarding the clip, and I’ll let it rest: I’m sure this is just an offshoot of the fact that nearly all of my clips are situated near the pommel, but the clip is bothersome when holding the knife for general use. The clip is my least favorite feature of the Covert by a long shot.

Deployment and Lockup

The Covert uses ambidextrous thumb studs for deployment. Personally, I love having thumb studs. The Covert’s thumb studs are accessible without being in the way, and they also serves as an external stop pin. This folder flicks open easily with a little wrist action. It glides open to a secure liner lock that is perfectly centered on my model. One thing I want to mention here is how well balanced the blade feels both while being snapped open and afterwards. Balance was obviously something the Colonel Rex Applegate and William Fairbairn wanted to be perfect. They achieved that goal.

The Covert features a liner lock with an external safety, called the “roto-lock”. The roto-lock is similar to CRKT’s Auto-LAWKS system, and requires the manipulation of a small lever on the spine of the handle prior to closing the blade. The locking mechanism naturally falls into place as your fingers find the deep finger choils and jimping. You pull the lever back (away from the blade) to disengage the liner lock. Although the liner lock and roto-lock are both made of relatively thin steel, everything is solid and exudes confidence. While I am not a huge fan of external safeties, I can see how this would make sense for a combat knife.

Gerber Applegate Fairbairn Covert Review – Final Thoughts

I honestly didn’t want to like this knife. Any time somebody puts a giant signature on the face of a blade it just rubs me the wrong way. I am also not a huge fan of the clip. My preferred blade carry position is tip up and I have to retrain myself when I decide to carry the Covert. This may not be a problem for some of you, and certainly not for folks that commit to one blade for universal everyday carry. I’m not that guy. For that reason, this knife doesn’t find its way into heavy normal rotation.

All that said, it didn’t take long for me to overcome those pet peeves when handling and using this knife. It just flat out does what it is designed to do and performance trumps aesthetics. I am glad I own the knife and many friends and colleagues seem to be drawn to it. I have every confidence in the workmanship of the blade and moving parts and really appreciate how it feels in your hand. I see it being a love-hate kind of knife depending on what features matter most to the buyer. Cost is always a factor and while the MSRP is $182, it’s readily available for under $100.

Gerber makes a ton of inexpensive, low quality blades in the lines they offer from overseas. The big retailers demand this (and so do consumers) and you can’t argue with demand for throwaway knives. The “Made in the USA” line appears to follow tradition of craftsmanship and attention to detail of old. If you’re a right handed, tip down carrier or if that isn’t a stumbling block, you should buy this knife. It may actually be a go-to tactical recommendation for those of you in that camp.

Regardless, you won’t be disappointed with the functionality of this balanced and functional folder designed by two of the biggest names in hand-to-hand combat training.

Gerber Applegate Covert Knife, Serrated Edge, Black, 154CM [05786]

Applegate-Fairbairn Covert double bevel titanium spear-style knife
154CM blade with titanium nitride coating
Features uncommon strength and balance
Includes patented Roto-Lock
An overall opened length of 8.7-inches and closed length 4.9-inches, with 3.78-inches of blade length; weighs 4.2-ounces

I recommend purchasing the Gerber Covert at Amazon or BladeHQ.

Editor’s Note: Please join me in welcoming Mike Teeples as a contributing author. Mike is from Colorado and brings his experience in hiking the Rockies and enthusiasm for all manner of edged tools to BladeReviews.com

Gerber Downrange Tomahawk Review

by Chad McBroom 4 Comments

The tomahawk is a North American hand-axe first used by the Algonquian Indians. Originally made from stone, the introduction of metal blades came with the arrival of the Europeans to North America. The tomahawk remains one of the most versatile bladed tools in existence. Modern uses of the hawk include breaching, rescue, survival, and close-quarter combat.

Buy the Gerber Tomahawk at BladeHQ

Buy on Amazon

The tomahawk has seen a huge surge in popularity over recent years. The Gerber Downrange Tomahawk is just one example of the modernization of this classic weapon and tool.

Purpose

From the moment you lay your eyes on it, it is evident that the Gerber Downrange Tomahawk has one purpose, and one purpose only—destruction! Sure, you can take this tool camping and use it to chop fire wood and drive tent stakes, but it would be like using a tank to drive your date to the prom. This tool is made for breaching—designed to remove unwanted doors form walls and unwanted walls from doors.

General Dimensions and Blade Details

The Downrange Tomahawk (DRT) has a three-purpose axe head designed to pack the most function into this breaching tool: A beveled edge for chopping through drywall, doors, vehicle skins, rope, etc.; a hammer head for busting locks, doorknobs, hinges, and the like; and a cutaway grip for controlling the pry bar end. Measuring at 19.27 inches, the Downrange Tomahawk is one of the larger “tactical” tomahawks on the market. While this makes it a little more cumbersome to pack around, it definitely adds to its leveraging capabilities when used as a pry bar.

With the exception of the welded on hammer head, the DRT is made from a solid piece of 420HC steel and finished with a black Cerakote™ coating. A sweeping beard that comes to a point at the heel gives this hawk excellent hooking capabilities, which can be used for ripping out the busted shards of its target, or for hooking onto stumps and logs when climbing up difficult terrain.

One of the major complaints that I have heard voiced by customers is the DRT’s lack of a sharpened edge. This usually comes from those who fail to understand the intent of this breaching tomahawk. A sharpened bevel is great for chopping wood and other cutting tasks; however, when it comes to breaching a door or cutting through the skin of a downed UH-60 Black Hawk helicopter, a sharpened bevel tends to over penetrate and get stuck, making the task more difficult. Gerber’s thought process then, was that their tomahawk could easily be sharpened for survival and bushcraft use, but with breaching and rescue being the primary focus of this design, a less aggressive bevel was ideal.

Handle and Ergonomics

The DRT has integrated tan G10 handle scales that contour with the jimping on the upper and lower portions of the handle. The bottom portion of the handle has jimping on both the front and back, whereas the top portion of the handle has jimping only on the front. The aggressive jimping makes for a very secure grip, especially when wearing gloves. The location of the jimping on the bottom portion of the handle is in the perfect location for gripping the tomahawk for maximum chopping leverage.

As mentioned earlier, the head doubles as a handle for the pry bar via a cutaway in the center. The addition of four finger groves creates a nice home for your hand inside the handle. There is also a small guard where the head and the handle meet. This guard protects your hand from getting smashed when you are choking up on the hawk.

Sheath

A tool like the DRT is rendered useless if it is not accessible when you need it. The best breaching tool in the world won’t open a single door if it is sitting back in vehicle you drove to the objective. The DRT is made packable through a MOLLE-compatible sheath system that incorporates a molded pry bar sleeve attached to nylon webbing. Two snapping retention bands secure the tomahawk in place. Two side-by-side MOLLE attachments at the top and a centered MOLLE attachment at the bottom of the webbing can be used to attach the DRT to a pack, standard webbing, or body armor so that the DRT goes where you go.

There is a separate portion of the sheath system that covers the tomahawk’s head. The head cover slides over the head and secures in place with a snapping nylon strap. This cover leaves the hammer head and the cutaway handle exposed so the pry bar and hammer can be used with the head cover in place. This reduces deployment time by eliminating the need to remove the cover unnecessarily, while acting as a safety measure to keep the edge covered during prying.

Testing

I took the DRT out to a building that was scheduled for demo and put it through the paces. Doors, drywall, and sheet metal were no match for the DRT. I was able to turn an interior door into splinters within a matter of seconds and the bevel worked like a can opener on the sheet metal. The pry bar also worked like a charm for separating doors from their frames. Using the hammer head, I was able to remove door knobs and hinges with a few whacks. Cinder block also proved to be of little consequence when it came to stopping the DRT.

Gerber Downrange Tomahawk Review – Final Thoughts

The Gerber Downrange Tomahawk is an extremely versatile breaching tool that performs as advertised. I was actually a bit surprised by its performance. I am a bit of a steel snob and 420HC is not one of my favorite steels. While 420HC is on the higher end of the 400-grade stainless steels, it is a low-grade blade steel generally speaking. I have learned, though, that I am often surprised by the performance of some of these lower grade steels when they are properly hardened. I have not tried putting an edge on the DRT, so I do not know how well this 420HC hawk will retain an edge, but as it is out of the box, it performed well.

Compared with offerings from boutique brands like Hardcore Hardware, RMJ Tactical, and Dawson knives, the DRT is priced appropriately at under $200 retail. I definitely recommend the Gerber Downrange Tomahawk for anyone looking for an effective breaching/rescue tomahawk.

Gerber Gear Downrange Tactical Tomahawk Survival Multitool, Camping Axe with Hammer Head and Steel Pry Bar, Includes Sheath with Integrated Molle Straps

DURABLE CAMPING GEAR: Features a multi-purpose breaching tool, with axe head with beveled edge, hammer head, and integrated pry bar for ultimate control in tactical situations
INNOVATIVE DESIGN: USA-made from 420HC steel with a corrosion-resistant Cerakote finish, ensuring this survival tool won't bend or break under pressure
VERSATILE OUTDOOR ACCESSORY: Combines the functionality of a tactical tomahawk, hammer, and pry bar in one compact multi-tool, perfect for various tactical and survival scenarios
COMPACT AND CONVENIENT: Includes a low-profile MOLLE-compatible sheath for easy attachment to your pack, standard webbing, or body armor, great portable tactical gear
OUTDOOR ESSENTIALS: Ideal for hunters, soldiers, tradesmen, and outdoor enthusiasts; a crucial addition to any tactical load-out or essential survival kit equipment; Backed by the Gerber Guarantee, a limited lifetime warranty

I recommend purchasing the Gerber Downrange Tomahawk at Amazon or BladeHQ.