USA Made EDC Knives

Benchmade 485 Valet Review

Last Updated: February 2, 2019

2013 and 2014 marked pretty quiet years for Benchmade. Not a whole lot of interesting stuff rolled off their shelves. The Volli was my favorite and has proven itself to be an excellent knife. Beyond that there wasn’t a whole lot to report.

Buy the Benchmade Valet at BladeHQ

Buy on Amazon

Benchmade’s 2015 SHOT Show releases actually looked pretty strong. The 485 Valet was one model that caught my eye. Perhaps most surprising was that the knives became available about a week after the show. Gone are the days of lusting over pre-production tools at SHOT only to find them released sometimes years later. Initially I was going to hold off on acquiring a Valet, but all it took were a couple positive affirmations from Tony regarding his knife and I had a Valet en-route to my office.

General Dimensions and Blade Details

The Valet has an overall length of 6.69″, a 2.96″ blade, and it weighs 2.18 ounces. The knife compares favorably to the Benchmade Mini Griptilian although it’s much sleeker. The low profile handle and spear point blade were innately appealing. This is a slim every day carry (EDC) piece that easily doubles as a gentleman’s folder with a more modern flair.

The Valet’s packs plenty of cutting edge, a high flat grind, and a sturdy tip all into a sub 3″ blade. The blade is ground thin and it almost cuts like classic slip joint (not a bad thing). I had no trouble zipping through boxes, bags, and all the little stuff that comes across my path. Everything from sliding between the folds of an envelope free a cable bill to de-boning chicken thighs for a stir fry.

Benchmade went with Bohler M390 stainless steel for the Valet. I have been putting M390 through its paces between this Valet and my ZT 0620. Heat treated to 60-62HRc, M390 is a super steel with superior edge holding abilities, yet it is still easy to maintain. I have been putting the Valet through it’s paces, and I’ve been happy with the results. I sliced up a big stack of cardboard in an informal “cut test” and managed to wear the edge down a bit after a while. I ended up sharpening the knife on the fine stones of my Sharpmaker. After just a few passes I could tell the edge was coming back, and I was able to quickly restore the edge to hair shaving, paper slicing performance. M390 is also very corrosion resistant.

M390 is apparently very expensive (on a podcast Tony and I determined that it appears to sell for 3x as much as a more normal steel). Given the option I would have selected a S30V or 154CM version if it meant a substantial reduction in purchase price, but I appreciate that Benchmade is interested in offering a premium product.

Handle, Ergonomics, and Pocket Clip

The Valet has a sleek gray handle with smooth G10 over milled out stainless steel liners, and a gray G10 backspacer. Handle construction is typical Benchmade quality. The G10 is contoured (3D machined) has been nicely finished. The steel liners are flush, and the backspacer sits solidly in the middle. I like the gray. It’s different, but nothing crazy. This isn’t a big handle, but it’s well made.

The Valet is a small knife and it feels like a small knife. I’m able to get a full grip on it, but there isn’t much room beyond that. It’s perfectly fine for little EDC tasks. There is no jimping, or much in the way of notable ergonomic features. The little knife sits in your hand well enough, and is more than adequate for normal use. I did not find the smooth G10 to be “slippery” and did not have any issues using the knife normally.

The pocket clip is a nice stainless steel deep carry clip. It buries almost completely into the pocket and is discrete. The handle is drilled and tapped for ambidextrous tip up carry. I like this clip and I think it works well.

The Valet also carries really well. At under 3 ounces and you quickly forget the knife is in your pocket. Perfect as either a discrete primary EDC or a lightweight backup knife.

Deployment and Lockup

This is an axis lock knife, with thumb studs. Usually, that would be all I need to hear, but I am concerned that this time Benchmade may have tried to do too much with too little. The positioning of the thumb studs and axis lock feels cramped. The axis lock is smaller than on other axis lock knives, and the thumb studs sit very close to the handle. The knife looks cool, and it certainly works, but it isn’t the most comfortable knife to open and close repeatedly. I’ll be curious to see if anyone shares that opinion with me.

Lockup on my knife is good. Out of the box there was a tiny bit of horizontal blade play, and a little more developed after a month of use. Pretty much all of my axis lock knives have a little play in them unless I tear them down and loctite the pivot. I know some people aren’t fans of the axis lock (too many moving parts and small springs to break), but I have always liked them. This one is smaller than I’m used to, but it still works.

Benchmade Valet Review – Final Thoughts

I am a little divided on the Valet. On one hand, it is a really slick little folder. I have been getting more and more into gents folders for daily carry, and visually this one ticks a lot of boxes for me. I like the smooth G10 handles, and the thin flat grind and spearpoint blade are excellent. My knife came well finished, and I didn’t run into any major QC issues that some folks have reported on first run Benchmades.

But a couple things turn me off on the Valet. The fiddly “landing gear” (small thumb studs placed very close to the knife and small axis lock) is my biggest concern. I would not recommend this knife for people with larger hands. I’m not Andre the Giant, but the position of the lock and thumb studs seems too tight for repeated use (or the mindless flicking open and closed of pocket knives while watching TV). Certainly this could be a “Your Mileage May Vary” thing. This is a beautiful knife, but I think BM leaned a little into far into “form over function” territory on this one.

I also think the price is also worth mentioning. $170 is a large sum for a small knife. I would have loved to see the Valet on the tail end of $150, and not on the tail end of $200. I realize that M390 is expensive material, and I think that folks who really appreciate a premium steel will have an easier time justifying the cost. Personally, I am not convinced this steel is worth the extra money.

But I don’t mean to end this review on a down note. The Valet potentially has a lot to offer. If it fits your hand well then there is little left to complain about. The Mini Griptilian is still my go to small Benchmade, but the Valet could be a worthy upgrade if it fits your hand and budget.

Benchmade - 485 Valet Knife, Drop-Point Blade, Plain Edge, Gray G10 Handle

HIGH-QUALITY: The M390 premium stainless steel blade offers exceptional cutting ability, wear resistance, and corrosion resistance. The G10 handle is durable, impervious to moisture, and stable under extreme temperatures.
WELL-DESIGNED: Benchmade's AXIS lock is exceptionally strong and fully ambidextrous. The 485 is a manual knife that can be opened and closed with one hand.
COMFORTABLE: The 485's lightweight design and contoured handle make it comfortable to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Valet 485's drop-point, utility blade style and all-around functionality make it ideal for everyday carry and use.

I recommend purchasing the Valet at Amazon and BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

GEC #47 Viper Review

by Dan Jackson 12 Comments

Last Updated: August 5, 2019
I have recently seen a resurgence of interest in classic slipjoint knives. Maybe folks are getting tired of shelling out $200+ for the latest framelock flipper. Or maybe they like the idea of carrying something their grandpa may have carried. Who knows for sure.

Buy the GEC Viper at KnivesShipFree

Personally I know over the past couple years my carry tastes have trended toward the traditional. I still enjoy the latest and greatest, but 2 of my favorite EDC folders in recent memory have been the Victorinox Cadet and Chris Reeve Mnandi. I loved the slim utility of the Cadet, and the leather ensconced classiness of the Mnandi. They are such excellent knives for my basic daily purposes.

Then reading Tony’s review of the Indian River Jack piqued my interest in GEC knives. I view some of these GEC slip joints as almost a cross between a Cadet and Mnandi: simple tools matched with higher end materials and finishes.

So today’s review is of the GEC Viper. Or the #47 as some call it. I don’t know what it is exactly about the classic swayback slip joint pattern, but I really dig these traditional wharncliffes. The Viper is a newer model, and it’s garnered a fair amount of enthusiasm amongst the traditional knife crowd, so I figured it would be a nice model to acquire for review.

I don’t proclaim to be an expert on these traditional knives. Heck I’m not an expert on knives at all (just ask Kershaw Thomas). But I enjoy cutlery and will do my best to share my opinion of this fine folder from Great Eastern Cutlery.

General Dimensions and Blade Details

The Viper has an overall length of 6.81″, a 3″ blade, and it weighs 2.7 ounces. I must not have researched this knife very carefully because when it arrived in it’s cardboard tube I was surprised at how big it was. This is a good size slippie, especially when compared to something like a Cadet. I grew to enjoy the size of the 47. After all, it was originally designed to be a working knife. It is also fine as a suburban EDC.

The Viper comes with a beautiful 1095 carbon steel warncliff blade. Mine has a high flat grind and swedge. The edge is very fine. It’s more of a microbevel than anything. The high carbon steel has been given almost a mirror polish. It looks good and I imagine it helps cut down on rust and corrosion. 1095 is not a stainless steel, and I have had it rust on a few of my fixed blades. By giving the blade a polish there is actually less surface area for rust.

But the cool thing is that the polished 1095 will patina. On my Sod Buster JR I decided to play around with a “forced” patina by slathering the blade in mustard. With the Viper I want the patina to form naturally, so I’ve just been using the knife as I normally would, and resisting the urge to dip it in a vat of honey dijon. So far the results have been cool. I like the character it has developed over the past couple months, and look forward to seeing how things progress.

One small complaint is the amount of branding that GEC etches onto the blade. In my pictures the etching has faded, but from the factory it comes with a very overt “NORTHFIELD UN-X-LD” logo smack dab in the middle of the beautiful blade. Yeah… no thanks. Mercifully, most of the logo rubbed off after an application of Barkeeper’s Friend, a cleaning product that should consider sponsoring the website given how much I talk about it.

The 1095 isn’t just good to look at. The blade of my Viper has been given a super keen edge, and the cutting performance has been really nice. The blade easily tracks through paper, and I’ve also used the knife for mild food prep, opening packages, etc. But the other weekend I really put the knife through it’s paces. I was tasked with cutting up a large quantity of cardboard with drywall joint compound on it that wouldn’t fit into a trash can. These slip joints are usually ground thin, and the Viper is no exception. It is a keen slicer and made easy work of the cardboard. At the end of the the edge had slowed down a little, but 1095 is very easy to touch up on a strop or corner of my Spyderco Sharpmaker.

Handle, Ergonomics, and Carry

GEC offers the Viper in a variety of handle configurations. Mine is bolstered with Che Chen Rosewood scales over brass liners. This is my first knife with rosewood. It’s a beautiful wood and I have seen it on many high end guitars. I love the fine cord-like grain and deep shimmering quality of the wood when you hold it up to the light. The handle has been beautifully finished. The edges are nicely chamferred, there are no gaps in the liner or backspring, the pins and lanyard tube are meticulously sanded down, and the silver medallion inset into the handle is flawless. When you turn the knife over to examine the back of the handle there is no gap or bump in between the back spring and spine of the blade. It’s a really nice and well made handle.

In hand the Viper feels like a spacious work knife should. Don’t let the wood handles fool you: this is still a high performance tool. Back before the days of titanium, G10 and stainless steel, these were the kinds of knives folks used every day. Working with the Viper you can understand why these kinds of handles have stood the test of time. They are basic and comfortable. You can definitely whittle some sticks, cut cardboard, or handle most other daily tasks with ease.

The Viper is without a pocket clip, but it came with a leather slip sheath. I enjoyed using a slip sheath with my Mnandi, and use a slip sheath with my Fantoni Dweller as well. This sheath is wider and thicker than I’m used to, but it’s sturdy and feels good in the pocket. I like this kind of carry – especially when working in an office. If the sheath is too bulky you could always throw the knife directly into your pocket.

Deployment and Lockup

I should probably change this section to “Walk and Talk” to fall more in line with the idiosyncrasies of traditional folders. After all, this is a slip joint with a nail nick. The knife doesn’t “deploy” and there is no lock up. The nail nick is easy to get at, and the backspring on the slip joint is surprisingly strong. This is a purposeful two handed opening knife. There is a dedicated half stop, and the backspring is almost flush at the half stop.

When closing the knife you need to use some level of care due to the strong back spring. There is a half stop, but if you aren’t careful there is still room for the meat of your finger to get pinched in between the ricasso and handle. The slip joint is sturdy and reassuring, and inspired enough confidence for me to take on tougher jobs. The spring itself is tempered high carbon steel. Still, you need to use some care when working with a knife like this. It’s not a locking folder, and it sure as heck isn’t a fixed blade. Make sure you are using the right tool for the job.

GEC Viper Review – Final Thoughts

The Viper has been a wonderful introduction to higher end US made slip joint knives. I really like the look of single bladed slip joints, and traditional wharnies, so it was easy to pick this one out of the GEC lineup when thinking of my first knife.

That said, I was still surprised at how much I have enjoyed the 47. This is a larger folder, but it is still innocuous enough to bring to work. It carries well, cuts cleanly, and is satisfying to open and use. The materials are great, the fit and finish are on point, and the price is reasonable. The knife is also made in the USA. At the end of the day I have an extremely hard time finding any kind of fault with the Viper. I could do without the lanyard hole, but I see why they included it. I am also not a huge fan of the amount of branding GEC etched onto the blade. Thankfully, that faded with cleaning. Beyond that I have no complaints.

I highly recommend the Viper if you are looking for a traditional folder or just an excellent EDC.

GEC Viper – From $82.36
From: KnivesShipFree

I recommend purchasing the Viper at KniveShipFree. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Buck Marksman Review

by Dan Jackson 12 Comments

Last Updated: December 2, 2019
You may have noticed a lack of reviews of Buck knives. I have nothing against Buck. I reviewed the Vantage a couple years back, and haven’t gotten around to reviewing anything else because nothing else in their lineup interested me that much. That is, until I saw the Marksman.

Buy the Buck Marksman at BladeHQ

Buy on Amazon

The Marksman is a collaboration with Grant and Gavin Hawk. Grant and Gavin are known for pushing the envelope with unique designs and locking mechanisms. They have done a number of collaborations with Kershaw, Chris Reeve, and Zero Tolerance. I think it was especially cool that they teamed up with Buck, because Buck is so well known as a traditional brand, and Grant and Gavin are so well known for re-imagining the folding knife. It is an interesting juxtaposition, and it definitely got my attention. Toss in a 154CM blade, bearings, “made in the USA” quality, and a retail price of under $100, and I’m thinking there might be room for another Buck review on this website.

General Dimensions and Blade Details

The Marksman has an overall length of 8.25″, a 3.5″ blade, and weighs 4.3 ounces. This full size knife feels surprisingly lightweight thanks to the aluminum handle. I have mostly been using the Marksman for yard work and weekend chores, and it has made a great carry for those heavier duty applications. I have cut down bamboo, busted open zip ties, broken down boxes, and performed mild food prep. The Marksman cuts well and is lightweight and functional.

It’s the kind of user knife like the Benchmade Volli, Hogue EX04, and Cold Steel American Lawman, that manages to remain in my collection. For whatever reason, most of my fancier knives end up getting sold, but I have a hell of a time parting ways with a good user.

The blade shape of the Marksman is classic Buck drop point. It has the oval thumb hole that they seem to favor, and the design is mild mannered when compared to the handle. It’s also a functional blade shape with a sturdy tip and high hollow grind. The blade has been left with a matte finish which isn’t anything too spectacular. You can still see some rough grind lines and the finish will pick up scuffs and scratches. The laser etched logos on the blade also has shown signs of wear and have faded after the occasional application of Bar Keepers Friend (a metal cleaner). I photographed the knife after using it regularly for a couple months and you can see how the black laser etching has been scrubbed away. I consider this a “happy accident” as I’m a big fan of sterile blades.

Buck went with good ole 154 CM stainless steel heat treated by Paul Bos. The edge has held up well and the Marksman is a fantastic cutter. I have mentioned earlier how I have been using this knife pretty hard (for me at least) and I have been pleased with the performance. It keeps a good edge yet remains easy to sharpen. I have always been a fan of 154CM so I am not particularly surprised by my experience. I will say that I have had 154CM rust on me a little on more than one occasion, so you need to keep an eye on it, especially if you are going to use the knife for food prep and not clean it like I have on several occasions. If you don’t let the knife get too crusty, a little of that Bar Keepers Friend will bring it back to new.

Handle, Ergonomics, and Pocket Clip

The Marksman has a black anodized aluminum handle with a steel backspacer. This makes for a lightweight and strong handle. The anodization on the aluminum has held up well and there are grooves milled into the handle for a little texture and visual interest. The backspacer integrates with the strap lock (more on that below) so you have something of a “closed construction” design. While aluminum isn’t the most sexy of handle materials, it is very practical. I think it suits the design of this knife. Although it first appears as if there is a lot going on with this knife, at the end of the day construction is simple and sturdy. All the pieces have been nicely finished and the handle has been well executed.

The Marksman is a full size knife. Ergonomically it is straightforward and performs like you would expect. What impresses me most when I use the Marksman is how nice and light it feels in hand. I will say that the strap lock is uncomfortable to use repeatedly – at least until you build some callouses up on your hands. The serrations on the lock are no joke, and they tore up my thumb at first. Having used the knife for months now I don’t feel anything uncomfortable, but it took some getting used to.

Buck went with a deep carry reversible pocket clip mounted on the butt of the handle. This is a lot like the clip found on the LionSteel SR-1. The clip itself is simple and sturdy. It buries the knife discretely into the pocket. I like the clip and the way the Marksman carries. It’s worth mentioning that the knife is fully ambidextrous.

Here is your pocket clip shot:

Deployment and Lockup

Grant and Gavin really know how to shake things up in the deployment and lockup section. Sometimes I find myself starting to yawn when I put this part of the review together, but the Marksman really gives me something to talk about.

So you are probably already aware that the Marksman uses a “strap lock” to lock the blade in place. Chances are you have never encountered a strap lock on a knife before. It’s a big strip of stainless steel that runs the length of the back of the handle and snaps into place over a protrusion on the back of the blade. What makes it cool is that in the closed position, it serves as a big spring, and when you hit the flipper the knife launches open effortlessly.

Here is a size comparison with a Spyderco Delica and Spyderco Endura:

I have never been a huge fan of assisted openers, but the action on the Marksman is really cool and satisfying. It’s unlike any other spring assisted knife I have handled, to the point where I am reluctant to even identify it as an assisted opening knife. Closing the blade is kind of like setting a bear trap, and the trigger takes only a very light touch. It makes a very distinct tinny sound when you deploy it. Even my girlfriend could pick up on the fact that something was different with this knife. If the novel deployment system wasn’t enough, Buck also included a caged bearing system. The bearings work great and the action is so smooth that the blade just falls shut. This is a knife that you can easily open with the flipper or the thumb hole.

To disengage the blade you have to pull up on the strap with the serrations on the side of it. The serrations are rough and your thumb will get chewed up when you first start using the knife – especially if you obsessively open and close it like I did. The initial pain is definitely a negative, but overall I found the strap lock mechanism endearing, and like it more than I thought I would. With some practice you can learn how to open and close the knife one handed. It takes some tough thumbs and a little finesse but even this southpaw has managed to figure it out.

Another interesting aspect about the lock is that it is fully adjustable with a set screw on the pommel. I have used the knife for months and have opened it thousands of times. I have yet to notice any blade play, but if some were to develop you could tune it out with the set screw and pivot.

Here is a parting shot with my Spyderco Para 2:

Blade centering is perfect on my knife.

Buck Marksman Review – Final Thoughts

The novelty of the Marksman is what made me buy it. The thoughtful design, solid build quality, and excellent performance are what made me keep it. I would have never guessed that I would like the Marksman as much as I do. I wrote this review back in 2014, and as I update it in 2019, the Marksman is still part of my rotation. It’s a truly excellent knife. Perfect for those looking for a workhorse EDC that’s different.

The knife definitely has some novel features to it, and it doesn’t disappoint in that respect. But at the end of the day what impresses me most about the Marksman is that it’s actually a really good knife. The strap lock is unique, and I love how the blade deploys. The knife is also lightweight, tough, and functional. The materials are all high quality and it’s nicely put together – especially at the price point and considering that it is USA made. It carries well, cuts cleanly, and is a lot of fun to open and close. The Marksman has really grown on me. I would go so far as to say this is one of my favorite designs in 2014. I am glad I gave it a chance.

With all of that said I realize that this knife isn’t for everyone. The futuristic design is bound to polarize people, and the strap lock and it’s sharp edges could be a deal killer as well. But if you are in the market for something different and like a good user blade, then the Buck Marksman should definitely be on your radar. I liked it so much it earned a spot on my recommended EDC knives page.

Buck Knives 830 Marksman Folding Knife with One Hand Opening Action

RAZOR SHARP BLADE- 3-1/2" Drop Point 154CM Steel Blade delivers excellent edge retention, corrosion resistance, and is suitable for heavy cutting applications. Closed Length 4-3/4" Weight 4.0 oz.
AMBIDEXTROUS ONE HAND OPEN - Opens with the flick of a finger. The unique SLS Strong Lock System is one of the strongest locking mechanisms on the market. Once deployed, it offers the strength of a fixed blade knife
SAFE AND SECURE GRIP - The Black anodized aluminum handle provides a comfortable and secure grip while you work. This tactical knife will hold up in the most demanding situations
CONVENIENT CARRY - Includes a removable, reversible, tip-up discreet deep pocket carry clip for easy attachment to your belt, pocket, or in your bag
MADE IN THE USA - FOREVER WARRANTY - Since 1902 Buck Knives has offered a lifetime warranty on our knives because we believe in the integrity of our products. This knife is proudly made in the USA.

I recommend purchasing the Marksman at Amazon.com or BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Rick Hinderer Knives XM-18 3.5 Review

by Dan Jackson 16 Comments

Last Updated: June 23, 2019
In the past I have compared knife collecting to mountain climbing. Certainly there isn’t the element of physical accomplishment, as the only thing that really gets a workout is your wallet, but there is that spirit of pursuit and of course the ascent up a pile of incrementally more expensive knives. When considering the “summit” in the realm of production knives three big players in the US market come to mind: Chris Reeve, Strider, and Hinderer.

Buy the Hinderer XM-18 at BladeHQ

Buy on Amazon

I have been tooling away at this website for the better part of 4 years now, and have already covered multiple Chris Reeve and Strider products, but I’ve yet to review a Hinderer. That is because I had yet to purchase a Hinderer until 6 months ago.

The reason it has taken me so long to review a Hinderer is the same reason why many people get so hung up on Hinderer knives in general. They are difficult to purchase unless you win a lottery at one of the knife shows Hinderer goes to, happen to qualify for Hinder’s active military / first responder program and buy directly from Hinder, or want to pay a substantial mark up for a Hinderer on the secondary market. With a retail price from Hinderer of $385, these knives were selling for $700, $800, $900+ on the forums. We could get into a huge debate as to whether they are “worth” the money. At the end of the day, they are worth what you will pay for them.

Over the past few years I have seen the secondary prices creep down a little, and was able to snag this new XM-18 3.5″ for $550. At that price I was comfortable buying the knife knowing that I could eventually sell it and recover most if not all of my money. Your mileage will vary.

General Dimensions and Blade Details

The 3.5″ XM-18 has an overall length of 8.25″, weighs 5.6 ounces, and of course it sports a 3.5″ blade. This is a very substantial tool. It is over half an inch thick, and was definitely not designed for desk jockeys like myself. Rick comes from a firefighting background, and built the XM with first responders in mind.

It’s a big and heavy knife designed to perform under the hugely demanding situations first responders run into. I run a small law office on the coast of Florida. The closest thing I come to being a first responder is responding to the office manager’s announcement that someone dropped off a dozen donuts in the break room. On weekends I mow the lawn, go to the beach, and occasionally write articles about pocket knives. Some might suggest the 3″ XM for someone like myself, but I have always wanted to check out a 3.5″ flipper slicer. So here we are.

The blade of the XM is Rick’s classic drop point shape. We have seen something similar to it in the myriad of KAI/Hinderer collabs that I have covered over the years. My particular XM has been given Rick’s “slicer” grind, which is his leaner more cutting oriented grind. Contrast this with his thicker reinforced “Spanto” grind. Even though this is the slicier of the two grinds, it’s still quite thick behind the edge and favors durability over raw slicing performance. I’m okay with that as it seems to suit the beefy, reinforced nature of the rest of the knife.

Hinderer offers their knives in a number of different blade finishes, and even a wharncliffe version now. Mine has been given a nice tumbled finish although you can also get them beadblasted, coated, or even hand ground by the man himself if you have the cash.

Over the years Hinderer has offered the XM in a proverbial cornucopia of different steels. The blade steel of this particular XM is S35VN which is probably what most of them are being made out of these days. S35VN is a good steel and has been adopted by Chris Reeve and Spyderco. The blade is heat treated to 60-61 HRc. This is a touch harder than what Chris Reeve has been heat treating his S35VN to, and the result is better edge retention, but it’s theoretically a little harder to sharpen. In use I have found that the edge stays keen, and I have only had to strop it to maintain sharpness. I haven’t had issues with rust, chipping, or anything else. No complaints here.

Handle, Ergonomics, and Pocket Clip

The handle of the XM is very well done. You have a G10 scale over titanium liner on one side, and then a full titanium frame lock on the other. Holding everything together is a bunch of custom hardware. This handle is beautifully made and you can really get to understand the quality of the XM by closely examining it. The parts are all overbuilt, but wonderfully finished. My titanium locking side has been completely stonewashed and this nice hard wearing finish compliments the blade nicely. It really is a beautifully made handle.

In hand the XM 18 is all business. Again, Rick designed this knife with firefighters and military in mind, and it’s a no-nonsense tool that works in a variety of grips. I have always been a fan of forward finger choils, and even without the choil there is plenty of room on this handle for large gloved hands. This is also a thick knife, and it really fills the hand. I can only imagine what the XM-24 is like. It’s probably akin to driving around in an S-Class Mercedes all day – solid and roomy. There is jimping on the spine, lock release, and pommel, but it’s wide soft jimping and doesn’t tear up your skin. I’d say the ergonomics are pretty solid with this one.

Hinderer equips the XM 18 with a reversible pocket clip. It’s not a deep carry clip and favors ease of access over concealment. It’s a big heavy knife, so you will feel the XM-18 in your pocket, but it carries alright for what it is. The clip sets into a recess in the handle so it’s a very sturdy design. I think it’s interesting that they include a “filler tab” for the clip mounting position you don’t use.

Deployment and Lockup

Hinderer offers these knives in flipper and non-flipper variants. Here of course I have the flipper version. Many view this as the knife that got the titanium frame lock flipper craze going, and the ZT0560 collab really brought that front and center to the masses.

What is sort of ironic about the XM-18 is that it’s not a particularly good flipper. Back when these first came out I am sure the flipping action was considered to be fine, but these days even my $30 Swindle out flips this knife. There are teflon washers inside and while I can pushbutton the blade open it isn’t a rocket launcher flipper by any stretch of the imagination. But that isn’t necessarily a kiss of death. This is still a very nice smooth knife with good action, and reliable deployment. You just need to decide whether you are looking for a really fast flipper or not. I will say the thumb studs work fine on this XM.

Lockup on this knife is the stuff of legends. The thick titanium lockbar engages early against the tang of the blade and there isn’t even a hint of play. The thumb studs double as blade stops and the stop pin is sleeved to avoid peening. There is zero stickiness to the lock despite not having a stainless steel lockbar insert. Also, lets not forget the inclusion of the Hinderer lockbar stabilizer. I’ve mentioned it in scores of other reviews, but this is where it all began. Lockup is just super duper good.

Hinderer XM-18 Review – Final Thoughts

Politics and price points aside, this is an impressive knife. I feel that there is a substantial bump up in beefiness and build quality when compared with a Strider or Chris Reeve offering, and it’s a big jump from Spydercos, Benchmades, and even new ZTs.

When I compare the XM to everything else I have reviewed before, I have to say that the XM is a different knife. It’s difficult to put into words, but it feels like every piece of this knife was first carefully contemplated, and then overbuilt and meticulously finished to a fanatical degree. This is an extremely solid knife and I am glad that I have finally been able to acquire one for long term testing.

That said, the 3.5″ XM-18 does have its potential draw backs. The fact that it’s heavy, and doesn’t flip very well are the biggest draw backs that come to mind.

This XM has been in my collection for several months now, and I’ve tried my best to approach the review cautiously given the enormous amount of hype built into these knives. While I can’t say I would spend $800 for one of these, I do think they are easily worth the $385 MSRP. At $550 I am less enthused, but still respect the knife for what it is. Like any other luxury good, some will love it while others will blast it as a ridiculous extravagance. Those that don’t like it can simply vote with their dollars and spend their money elsewhere.

Personally I view this as either a dedicated tool or a collectible. It’s not a daily carry item for me. But again, I don’t work as a first responder. I “need” this knife for work much like I “need” a Hummer to accomplish my 20 minute suburban commute every day. That said, I realize there are plenty of people who may actually need, or want, an over built knife like this. And if that’s the kind of knife you are looking for, Hinderer delivers in spades.

I can say without hesitation that the XM-18 is a beautiful knife, and I recommend checking one out if you are at all interested in it. I am glad I did.

Rick Hinderer Knives XM-18 3.5 – $550.00
From: BladeHQ

RICK HINDERER XM-18 3.0 SPANTO-WORKING FINISH

KnifeArt has a great selection of Hinderer XM-18s, and they pop up on BladeHQ as well. And lately Amazon has been stocking them as well. I recommend purchasing them at these retailers. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Zero Tolerance 0562CF Review

by Dan Jackson 47 Comments

Last Updated: July 14, 2019
By this point we have seen quite a few of Hinderer / KAI collabs hit the market, and I have covered them extensively on the blog. We started with the heavily built 0550, moved to the critically acclaimed 0560, a knife that raised the standard for high end production pieces, spent some time with the controversial Kershaw Cryo, and recently the EDC-friendly Zero Tolerance 0566.

Buy the ZT 0562 at BladeHQ

Buy on Amazon

The KAI/Hinderer collaborations on go back a couple years, and surely by now everyone has had their fill of folders that resemble the XM-18. But still Zero Tolerance has insisted and recently released the 0562cf and the 0562.

“So what?” You might say, pointing to a drawer full of ZT boxes. You may be sick of hearing about ZT and Rick Hinderer pairing up. Well, the problem with the 0562 is that it may very be the best Zero Tolerance / Hinderer collaboration yet.

General Dimensions and Blade Details

The 0562 has an overall length of 8.25″, a 3.5″ blade, and weighs right around 5.5 ounces. The knife is smaller than the 0560, and bigger than the 0566. I know that a 3.5″ blade is a sweet spot for a lot of people’s daily carrys and it also happens to be the same footprint of the 3.5″ XM-18, which I consider the flagship XM for some reason. The 0562 carries discretely in blue jeans, but is big enough to be used as a work or self defense knife.

This is a good point in the review from me to distinguish the 0562 from the 0562CF. The 0562CF (pictured in this review) is the upgraded version of the knife with a carbon fiber handle scale and satin finished M390 blade. The 0560 is more of a working man’s version with a G10 handle scale and stonewashed Elmax blade.

For a detailed comparison of the two with beautiful photographs I invite you to check out my friend John Holbrook’s article and review of both knives here. Of course I’m only reviewing the 0562CF here, and went for the 0562CF because it was only $50 more and I was feeling fancy, but I think 95% of this review will apply to both models.

The blade on the 0562 is classic Hinderer drop point, modeled closely after his XM series of knives. The interesting thing about this particular model is that it has been given Rick’s “slicer” grind. The slicer grind is a slanting high flat grind that shaves quite a bit of material from his standard “spanto” grind. The slicer grind on this 0562 is actually pretty slicey, easily cleaving cardboard and rope. I find that Rick’s slicer grind on the regular XM is still pretty thick. This 0562 is the best slicing Hinderer collab I have handled.

The 0562 comes in either M390 or CTS-204P steel. My 0562 came in M390. M390 is a powered super steel by Bohler, and is capable of both being heat treated to 60-62 HRc and taking a beautiful polish. I have found edge retention to be excellent on M390. M390 is also relatively easy to sharpen for a super steel, making it a practical choice for someone that wants to regularly use the knife.

I am less familiar with CTS-204P, having only experienced it with my Spyderco Southard. In my experience CTS-204P also holds a nice edge and is reasonable to sharpen. I have had no problems with rust or corrosion. The jury is still out in terms of my long term opinion on 204P, but my gut reaction is that you will be fine with CTS-204P.

Handle, Ergonomics, and Pocket Clip

Just like a real XM, the handle of the 0560 is slab carbon fiber/g10 over a full stainless steel liner and then a titanium frame lock. You don’t have the extreme 3-d machining found on the 0560, which is fine by me because I think it’s part of the reason why they were able to keep the price down on these, but the edges are all chamfered.

Handle construction is very good. Zero Tolerance is no stranger to the world of high end production pieces, and they have struck a nice balance here of providing us with a sturdy knife with simple high end finishes like blackened barrel spacers, an oversized decorative pivot, and very good fit and finish. Compared with a real XM-18 3.5″, the 0562 is a much slimmer knife.

I really like the way the 0562 feels in hand. Gone is the terrible overly sharp jimping on the 0560. In its place you have a short row of tasteful and practical thumb jimping on the spine and a little recessed jimping by the pommel. The rest of the knife is smooth as a baby’s butt, although you do have a couple finger choils in the handle. I think they struck a great balance here and the 0562 feels very good.

For lovers of deep carry pocket clips, the clip on the 0562 is a triumph. It’s a very deep and discrete stainless steel clip that mates to a standoff at the very back of the knife. The end result is a fully ambidextrous clip that doesn’t leave a lot of holes in the handle. I am impressed ZT went this more stayed route rather than a flashy “ZT” branded clip. This level of restraint and classiness isn’t always found on their models so I gotta give credit where its due.

The spring action on the pocket clip is nice and strong and it holds the knife in place in your pocket. The 0562 is over 5.5 ounces, but it’s still a relatively thin knife and carries well for its size. All said I’m very pleased.

Deployment and Lockup

I am also pleased to report that the action on the 0562 is very good. Once again ZT has dialed in their detent and the blade explodes from the handle with the push of a finger. It doesn’t hurt that the blade rides on their proprietary “KVT” caged bearing system. Deployment is fast, reliable, and fun, and the blade falls back into place upon disengagement. The “thumb studs” are actually blade stops and I was not able to use them to open the knife.

For lockup we have a titanium framelock with a stainless steel lockbar insert. This is just like the lockbar insert found on the recently reviewed ZT 0808. It has been very well done. Lockup is early and confident, and there is no blade stick, lock rock, or any other malady that sometimes effects a framelock knife. Blade centering is dead on too. Rounding things out is a Hinderer lockbar stabilizer.

Zero Tolerance 0562CF Review – Final Thoughts

I have handled all of the Zero Tolerance / Hinder collaborations prior to the 0560 and I also recently broke down and finally picked up a Hinderer XM-18, so I thought that I have pretty much seen it all. The 0562 is still a very impressive knife. They have done a great job combining fixing the things that I didn’t particularly care for about the original 0560 (the oversize knife, sharp jimping) and added some nice subtle refinements and upgrades. I think they also did a good job not bringing over some aspects of the XM-18 that I could avoid (the 3.5″ XM-18 is very heavy and the action isn’t particularly impressive). The end result is a practical and well made knife at a competitive price point.

I know that some will want to know if the 0562 is as good as an XM-18, or whether will replace an XM-18. I’m here to say that those are still two very different knives. My 3.5″ XM-18 is an absolute tank. It’s over the top in many ways. I prefer the 0562 because it’s slimmer, more pocketable, cuts better, and flips better, and can be had for a fraction of the price of the XM, but I still appreciate the XM-18 for what it is: a finely tuned overbuilt hunk of G10, steel, and titanium.

I realize that I’m somewhat jaded by running this website, but I thought $250 for the Zero Tolerance 0562CF was very reasonable for what you are getting, and the G10 version retails for right at $200. I know a $200+ folding knife isn’t for everyone, but if you can justify buying a $200+ pocket knife then I’m here to say the ZT 0562 is awesome.

Zero Tolerance 0562CF Hinderer Slicer Folding Knife; 3.5” CPM-20CV Stonewashed and Satin Steel Blade, Carbon Fiber Front Handle, KVT Ball-Bearing Opening, Frame Lock and Reversible Pocketclip; 5.5 OZ, Black

Ultra-premium, durable CPM 20 CV stainless steel blade with stonewash and satin finishes offer outstanding edge holding capability and corrosion resistance
Hinderer flat-ground “slicer” grind provides both slicing efficiency and a tough point; handle has carbon fiber front scale and stonewashed titanium back
Reversible deep-carry pocketclip for left or right-handed, tip-up carry
Ideal EDC essential for everyday tasks—slicing, survival tool, cutting boxes, self-defense, tactical use or as the perfect gift
High quality, general all-purpose knife great for EDC or use when camping, fishing, hunting, working, utility or outdoor activities.Handle Length:4.75 inch

I recommend purchasing the ZT 0562CF at Amazon or BladeHQ . Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Zero Tolerance 0801 Review

by Dan Jackson 7 Comments

Last Updated: August 7, 2019
Titanium framelock flippers. Are we sick of them yet? No? Great, because I’ve got another titanium framelock flipper review for you today. Given the rapid influx of titanium framelock flippers on the market, I initially thought that I would pass on the Zero Tolerance 0801. The wide shape, chunky build, and monochromatic look of the knife all lead me to quickly dismiss the knife.

Buy the Zero Tolerance 0801 at BladeHQ

Buy on Amazon

It wasn’t until I handled the 0801 in person that I decided to buy the it. Oddly enough, I became so intrigued that I ended up acquiring 2 of these at once – the standard version, as well as the 0801CF “Copperhead” limited release version of it. This review will focus on the 0801, as the 0801CF is a true collectible that I ended up selling off and never using.

Designed by acclaimed custom maker, Todd Rexford, this understated design is based off of his Singularity custom offering. The 801 is the second in a string of collaborations Todd has done with KAI (the previously reviewed Kershaw Injection being the first). This is his first high end collaboration with Zero Tolerance.

General Dimensions and Blade Details

The 0801 has an overall length of 8.2″, a 3.5″ blade, and weighs 5.85 ounces. The 0801 is a substantial knife and you will feel it in your pocket. It isn’t quite as chunky as the 0550, but it’s pretty darn close. No doubt that is due in part to the thick full titanium handle. I can’t think of any other production full titanium flippers on the market at the moment, so that is something to keep in mind. I like the fact that ZT has introduced a full TI handle into their lineup. Just understand that the 0801 ain’t no feather.

The blade on the 0801 is a spearpoint shape with a high flat grind. There is also a swedge that terminates well before the point to support the tip. The blade shape, like the rest of the knife, is pretty sober looking. But it certainly functions well in normal cutting tasks like breaking down cardboard boxes, doing light wood processing, and other general utility tasks. The blade is pretty thin behind the edge and the knife comes very sharp. It’s nice to see a high performance grind on this kind of knife, as the ZT/Hinderer collabs seem to favor strength over slicing.

The 0801 comes in Elmax steel. Elmax has become a staple in Zero Tolerance’s higher end line up. I have come to enjoy Elmax for its combination of good edge retention and relative ease of sharpening. I have had zero issues with rust or corrosion. I think Elmax is a good choice in this higher end offering.

Handle, Ergonomics, and Pocket Clip

The 0801’s full titanium handle slabs are separated by three black standoffs. This knife has been well executed. There are no visible machining marks, all the parts line up well, and everything has been nicely finished. The oversized decorative pivot is a nice detail, and the black hardware serves as the only contrast on the knife. The handle slabs themselves have been milled out with grooves and has a sort of sweeping faux bolster look. I am not wild and crazy about the grooves or the “ZERO TOLERANCE” brand engraved into the handle, but I have to admit Jim Skelton’s customized version with blue two-tone anodizing job really pops.

The 0801 works fine from an ergonomic standpoint. I wear a large glove and there is just enough room for a 4 finger grip – those with freakishly large hands may run out of real estate. There is something of a forward choil, so you can choke up and get a little more out of the handle if you need to, or lay back for more powerful cuts. There isn’t any jimping on this one, so you don’t have to worry about hot spots for your thumb, but I readily acknowledge that the absence of jimping may be a turn off for some. The rest of the handle feels good. This isn’t a funky handle shape so it should work well for most people.

The pocket clip on the 0801 is straight out of the KAI parts bin. A slightly smaller version of the clip can be found on the Cryo. Visually it’s not the most amazing clip, but it is very practical, especially if you are into deep carry. The 0801 buries into the pocket, but even if your co-workers won’t notice it, you certainly will. At near 6 ounces this is not a lightweight pocket knife. That’s the trade off when you go for a thick full titanium handle. It would be cool to see ZT pocket out the inside to lighten things up, but I know that is probably cost prohibitive. If you are into bigger, heavier knives this obviously won’t be an issue, but weight weenies need not apply.

Deployment and Lockup

As far as titanium framelock flippers go, the 0801 is up there with the best on the market. I’m not saying it’s as good as the freakishly fast 0454… it’s definitely nothing near that, but fans of snappy flippers should still be satisfied with this knife. The Elmax blade rides on KAI’s KVT captured bearing system, and you can see the guts of it peeking out by the lock face. I thin it is somewhat unseemly to have the bearing cage poke out like that, but I guess that is what needed to be done to make the knife work right. All said, fans of flippers will find a lot to like with the action of the 0801.

ZT incorporated a stainless steel lockbar insert into their frame lock, and the steel on steel contact makes for a secure and stick free engagement. I couldn’t detect any sort of blade play. The lock geometry of this knife has definitely been dialed in, and the blade centering is perfect. These details are important to find in this higher end knife.

Zero Tolerance 801 Review – Final Thoughts

There isn’t anything else out there filling the full titanium framelock flipper niche, so off the bat that puts the 0801 into a league of its own, unless of course you are willing to venture into custom, midtech, or aftermarket territory. The full titanium handle does have its potential drawbacks, mainly the weight, but there are plenty of people willing to forgo an ounce or two for full TI goodness.

Despite not having any direct competition, the 0801 doesn’t rest on its laurels. It is a very solid and well made knife. Build quality and materials are both excellent. The flipping action and lock up are superb. The design is austere and based off of Todd’s coveted custom offering. There is a lot to like here for fans of high end production knives and frame lock flippers. If you are interested in the 0801 I can safely recommend it.

Zero Tolerance 0801 Titanium Flipper Knife

Made in the USA; Manual open, KVT ball-bearing system
Frame lock; Reversible (left/right), deep-carry clip
Steel: ELMAX, stonewashed finish; Handle: Titanium
Blade Length: 3.5 Inch (8.9 cm); Closed Length: 4.7 Inch (11.9 cm)
Overall Length: 8.2 Inch (20.8 cm); Weight: 5.8 ounces (164.4 g)

I recommend purchasing the 0801 at Amazon or BladeHQ.