Dan Jackson

Dan is the creator of BladeReviews.com. He founded the site in 2010, and for the first 5 years Dan wrote all of the reviews and recorded all of the video reviews. He grew up using pocket knives, and the decision to start the website stemmed from his fascination of all things sharp combined with a deep passion for writing. At this point he has personally reviewed almost 300 knives of all shapes, sizes, and price points. He is widely recognized as an authority on daily carry knives and has consulted with knife companies on product design and has been featured on national media outlets including the WireCutter. In 2016 Dan decided to branch out and experiment with the website by reviewing watches, flashlights, and multi-tools. Today BladeReviews.com features a number of expert authors reviewing a wide range of daily carry gear. He is proud to write detailed long format reviews with original photography. The website remains largely independent with the vast majority of the products reviewed being purchased by Dan personally. When he isn't writing knife reviews from his home in Southwest Florida, or talking about himself in third person, he enjoys practicing law, reading, fishing, cigars, and weight lifting.

At this point he has personally reviewed almost 300 knives of all shapes, sizes, and price points. He is widely recognized as an authority on daily carry knives. He has consulted with knife companies on product design and his opinions on pocket knives have been featured on national media outlets including the WireCutter. In 2016 Dan decided to branch out and experiment with the website by reviewing watches, flashlights, and multi-tools. Today BladeReviews.com features a number of expert authors reviewing a wide range of daily carry gear. He is proud to write detailed long format reviews with original photography. The website remains largely independent with the vast majority of the products reviewed being purchased by Dan personally.

When he isn't writing knife reviews from his home in Southwest Florida, or talking about himself in third person, he enjoys practicing law, reading, fishing, cigars, and weight lifting.

Kizer Intrepid Ki4468A1 Review

by Dan Jackson 7 Comments

Last Updated: August 12, 2019
The high end Chinese Renaissance has been blossoming for a couple years, and Kizer is arguably the Michelangelo of the movement. Yet there hasn’t been much coverage here of this rapidly expanding segment of the market. Ben has capably covered a couple knives from Kizer including the original Ki3404-A3 and the Vanguard version of the Gemini. I have been curious about Kizer myself, and recently acquired a Rogue and an Intrepid, the subject of this review.

Buy the Kizer Intrepid at BladeHQ

No products found.

Like the Gemini, the Intrepid is another collaboration with custom knifemaker Ray Laconico. But rather than this being a knife from the more affordable Vanguard series, we have the premium offering here replete with S35VN blade steel and sculpted titanium handles. What I find interesting about Kizer knives is their singular focus on quality. This fanaticism has gone so far that they import their materials from the United States and Japan. That doesn’t sound at all like the Chinese manufacturers of yesteryear. I think a review of a modern high end Kizer is long overdue here.

General Dimensions and Blade Details

The Intrepid has an overall length of 8.25″, a 3.625″ blade, weighs 5.64 ounces, and is made in China. This is the bigger brother to the Gemini, which has a 3.125″ blade a weight of 3.65 ounces, and a much simpler and more “socially acceptable” profile. Although the Gemini is a more practical Every Day Carry (EDC) option, I wanted to check out the Intrepid because we already have an excellent review of the Vanguard version by Ben. Tony does a great job as usual with his review of the dress version.

The Intrepid is bigger and badder than the Gemini, and it features a large modified clip point blade. I always enjoy a good clip point, and this one is no different. Actually, it’s a little different in that the blade has a harpoon, but it works much like a regular clip point. The draw to the harpoon is that it makes for a good thumb rest and funkier looking knife. I like the unique blade shape. The hollow ground blade gets thin behind the edge, and the edge itself has been evenly ground. The swedge and belly meet to form a needle sharp tip. Although they are more aggressive looking, clip point blades are well rounded performers, and this blade is great for a variety of tasks.

Kizer selected CPM-S35VN steel for the blade. S35VN is a popular choice, and I’m glad to see it here. This is an American steel made by Crucible with input by Chris Reeve, and the end result is a blade steel that is a little tougher and easier to sharpen than S30V. It also finishes nicely, and the blade of the Intrepid comes with a nice stonewashed finish.

I have carried and used my Intrepid extensively. I continue to be impressed by the ease of maintenance and edge retention on S35VN. My knife came sharp straight out of the pouch and I have used it for a variety of domestic chores including breaking down boxes, working around the house, and a little woodworking now that the weather here in Florida has finally cooled off.

Handle, Ergonomics, and Pocket Clip

S35VN blade steel is all well and good, but what really impresses me with the Intrepid is the handle. Here we have full 3-D contoured titanium handles. These handles are milled, not cast, and if you look closely you can see the cutter path You just don’t see much of this. Probably the closest competitor I have reviewed with contoured titanium handles is the Spyderco Slysz Bowie. The Slysz Bowie is immaculate, but it’s also nearly $100 more than the Intrepid.

This 3-D contoured handle comes with all the fixings you would expect in a premium titanium framelock flipper: oversized pivot, steel lockbar insert and overtravel stop, and a blue anodized titanium backspacer. Fit and finish is perfect on my knife.

Being a larger knife, the Intrepid has plenty of room for your hand and should accommodate most people with ease. The finger groove and broad spine both naturally draw in your hand. This is a comfortable piece that works well. There isn’t much in the way of a “traction plan”, but somehow the knife has managed to stay in my hand. The bead blasted titanium offers a little traction, and in my opinion the lack of jimping is a pleasure, not a curse. If you want something a little higher traction then I’d probably suggest the G10 handled version.

The pocket clip is understated when compared to the rest of the knife. This is a simple folded titanium clip, and the only adornment is the fact that it has been anodized blue to match the hardware and backspacer. That’s OK with me because the clip works. It has excellent spring retention and the knife stays firmly in place – even when clipped to lighter fabrics. This is a big knife, but it carries like a smaller blade thanks to the strong clip and slim handles.

The only potential negative is that the handle is only drilled and tapped for right side tip up carry. Not a problem for me, and I’d hate to see them drill any more holes in this handle than absolutely necessary.

Deployment and Lockup

The Intrepid is a flipper on caged ball bearings. The bearings are smooth and the blade flips with authority. For people that like metrics, I’d say it’s a strong “8” on my 1-10 flipper action scale. It flips only crisply and reliably every time. The flipper tab is large, angled, and easy to get at. There is no jimping on the flipper tab, but once again we don’t need it. Clearly the guys at Kizer have spent some time studying the American flipper market and know what we want. This thing sings.

For lockup we have a titanium frame lock. This lock has been outfitted with a stainless steel insert that doubles as a lockbar stabilizer, much like the Spyderco Domino and some of the Zero Tolerance flippers. Lockup is early without being too early, and secure without being sticky. Lockup is also rock solid. No blade play, no wiggle, and no tweaking required. I’d say the flipping action and lockup is on par with Zero Tolerance, a company known for making some of the best production flippers in the business.

Blade centering is perfect on my knife.

Kizer Intrepid Review – Final Thoughts

I was wrong to wait so long to check out these Kizer flippers. The Intrepid has everything I look for in a titanium framelock flipper and then some. Here we have a great design, premium materials, superb fit and finish, nice details, and a dialed in flipper. This is a bigger knife, but it carries like a smaller knife, and for a little over $200 you are getting a lot for your money. The 3-D machined handle is what sets the Intrepid apart. Offhand I can’t think of any production titanium framelock flippers with fully contoured titanium handles.

Here is a shot of the Intrepid next to the Hinderer MP-1:

The Intrepid is about the same size and thickness as the recently reviewed Hinderer MP-1, but it feels slimmer and more than .2 ounces lighter (the difference on paper). Granted the Hinderer is a tank and this is something of an apples to oranges comparison, but I still find it interesting to juxtapose these knives. The build quality on the Hinderer is superior, but the Intrepid is a special knife in its own right.

I recommend Intrepid if you are looking to scratch that higher end titanium frame lock flipper itch. There is a lot to like here, and again I can’t think of another flipper that has a handle like this.

I think the Vanguard version will also be a good buy if you want something at a more approachable price point. And check out the Gemini if you are wanting a more urban friendly EDC. Either way I don’t think you will be disappointed with these Kizer / Ray Laconico collabs.

No products found.

I recommend purchasing the Kizer Intrepid at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Hinderer MP-1 Review

by Dan Jackson 2 Comments

It seems like every time I write a review of a Hinderer knife I can’t help but open with a commentary on the state of the Hinderer market. Maybe it’s the finance degree talking. At any rate, a few years ago a Hinderer XM-18 would sell for well north of retail. Some were selling for close to $1,000.

Buy the Hinderer MP-1 at BladeHQ

[easyazon_cta add_to_cart=”default” align=”center” asin=”B0773W7LPG” cloaking=”default” height=”42″ key=”tall-orange” localization=”default” locale=”US” nofollow=”default” new_window=”default” tag=”brdfkdfk-20″ width=”120″]Amazon[/easyazon_cta]

Those prices slowly began to drop from their peak, and when I wrote my review of the XM-18 3.5″ back in October 2014, I paid around $550 for the knife. Still about $150 above retail, but a far cry from the $800+ they were commanding when I was seriously getting into knife collecting in 2011-2012.

Fast forward to October 2015 when I reviewed the XM-18 3″. I paid $385 for that knife, which is right around retail.

And oddly enough I bought my MP-1 right around the fall of 2016, and I paid $450 for it on the secondary market. It retails for $695 on Knife Art. Things sure have changed. Who would have guessed that you can buy a Hinderer for below retail on the secondary market? Probably not the guys that paid $1,000 for their XM-18s.

Regardless of the reason I won’t complain. It allowed me to pick up the MP-1 at a nice price for this review. And the MP-1 is an interesting piece that I might not have checked out at full retail. It shares a lot of similarities to the XM-18, but it’s stockier in build. This knife also comes with a new feature. MP-1 stands for Modular Platform-1, and this knife’s selling feature is a removable backspacer that can be swapped out with various other backspacers. I am not sure if the replaceable backsapcer on its own it would be reason enough to buy the knife, but the rest of the MP-1 was intriguing.

General Dimensions and Blade Details

The MP-1 has an overall length of 8″, a 3.5″ blade, and weighs 5.9 ounces. This knife was designed by Rick Hinderer and is made in the USA. The MP-1 a substantial knife and is about half an ounce lighter than a G-10 handled XM-18 3.5″. Personally, this is not the most practical Every Day Carry (EDC) knife, but it’s beautifully made with lots of detail. The workmanship is unmistakable and I have spent many evenings admiring this knife. While I have carried and used my MP-1, my ideal EDC knife is usually about the size of a Sage 1. I am sure some carry theirs religiously, but must confess this is more of a collectible for me.

The MP-1 has a modified sheepsfoot blade, not dissimilar to the Benchmade Triage rescue knife. This lends a friendlier profile to the MP-1 and gives it a workmanlike feel. Sort of like the orthotic sneakers old people wear. Its much less aggressive than the original XM-18 line. While there are some design flourishes to elevate the MP-1, at the end of the day this is a comfortable and practical knife if you can get over the weight and thickness of it. This blade cuts well with a high flat grind. The tip is a little lower on this knife but is still surprisingly fine. You can easily pierce materials with it without it being needle sharp. The edge has been ground perfectly.

The MP-1 comes with S35VN blade steel. S35VN isn’t super high end stuff, but it’s totally adequate here. I don’t necessarily need this thing to come in S110V, although I suppose that would be interesting. S35VN is a great higher end working steel. Easy to maintain, yet it holds a good edge, is reasonably tough and corrosion resistant. It has become one of my favorite steels for an EDC knife. Similar to CTS-XHP in that it’s just a good all round steel and you won’t need a diamond stone to bring an edge back on it.

These days I tend to gloss over the knife steel part of the review unless it’s a new steel or I really have something to say (beyond my practical observations and a few general words on the steel itself). If you want a deeper dive into blade steel, chemical composition, etc., then I suggest checking out the knife steel section of the website.

Handle, Ergonomics, and Pocket Clip

This is a full titanium framelock flipper made by Hinderer. That is to say, it’s both beautifully built and totally overbuilt. They started with two thick pieces of titanium for the frame, and sandwiched it between oversize custom stand offs and a large custom pivot. Fit and finish is exceptional. The titanium has been finished to a buttery smooth texture. The edges have been chased with decorative chamfering while the diamond pattern found on the G-10 scales of the XM-18 have been machined in little reliefs on the handles. The blade, backspacer, pocket clip, and handle all have been stonewashed while in contrast the hardware is satin finished, leaving you with a dramatic monochromatic knife.

The handle may be overbuilt for most normal people, but you can’t deny the beauty of it. I especially like the extra details found on this model. The quality of the workmanship reminds me of my old Shirogorov 95-T. We are talking about the higher end of the production pocket knife section. No one “needs” a knife like this, but enthusiasts of high end knives appreciate these in the same way you would appreciate a nice watch, high end leather goods, or any other type of luxury product.

Since this knife was apparently named after a Hinderer’s new Hinderer Modular Backspacer System (H.M.B.S.), I better spend some time to talk about it. This is a backspacer that can be removed with a single torx screw rather than disassembling the entire knife. The backspacer wraps around the stand offs and the torx set screw holds it all in place. The stock backspacer is a geared affair that comes with an oversized lanyard loop, but RHK offers a variety of backspacers that include bottle openers, impact tools, various anodized options, etc. In practice it works as advertised. Its easy to take it out with the turn of my WiHa driver.

Here is a video by Rick Hinderer himself explaining the H.M.B.S. in more detail. I think looking at the below picture will save you the 10+ minutes. It’s pretty straight forward.

Whether it is something you want to play around with is an entirely different story. Some get a kick out of modding their Hinderers with anodized parts, after market filler tabs, new scales, etc. No doubt the MP-1 is designed to cater to that crowd. Personally, I like the stock backspacer, and the knife seems a little empty without it. I probably won’t be buying any additional backspacers, but I can see the appeal. All in all I think they did a good job with the execution.

As I mentioned earlier, the MP-1 is a comfortable knife. You would hope so given how thick it is. While the knife has some ornate flourishes, at the end of the day the handle is simply shaped. It’s comfortable and will accommodate a variety of hand sizes and grips. There is a small forward choil behind the edge that gives you extra options and control. There is flat top jimping on the spine of the blade and backspacer, and the milled handles also provide a little traction. The titanium has a great feel in hand, and overall the MP-1 is a pleasure to hold and use.

The MP-1 features the same spoon style pocket clip of the XM-18 series. That’s nice because it’s a good pocket clip design. Retention is excellent and the MP-1 stays in place when clipped to your pocket. This isn’t a deep carry clip, and the MP-1 isn’t the most discrete of carries, but the knife mostly buries into the pocket. Being a thick and heavy knife, it isn’t going to EDC like a Dragonfly, but it does stay in place and out of the way. This carries as well as any other 6 ounce knife I have owned.

Also, just like with the XM series, the MP-1 is ready for right side tip up or tip down carry. There is a “filler tab” screwed in place near the pivot.

Deployment and Lockup

The MP-1 has an odd combination of thumb studs and flipper. I say “odd” because the thumb studs do not work unless the blade is partially open. I suppose it’s used in the event the flipper does not completely deploy the blade. That’s a real potentiality on the XM-18, which has a notoriously weak detent, but here the detent on the MP-1 is pretty good. The blade opens reliably and I’d say this flipper is a solid “6” on a 1-10 scale (with a 10 being something like the ZT 0454). Action is crisp, but it is possible to occasionally “flub the flip” and get a partially deployed blade. The knife uses teflon washers. Action is smooth and the knife flips open, so I can’t complain.

With the XM series the thumb studs are technically blade stops, so it could be argued that they don’t “need” to work as thumb studs. Here, the MP-1 actually features a set of hidden blade stops that travel underneath pockets milled out in the handle, so the non-functional thumb studs are a little more puzzling. They do come in handy if the blade doesn’t fully open with the flipper. Beyond that I don’t see the point to them.

For lockup we of course have a titanium framelock. This is just bare titanium against the steel tang of the blade. No steel inserts, although you do have the Hinderer lock bar stabilizer peeking out from behind the pocket clip. My lock has been executed beautifully. The lock face is generous and lock up is around 30%. There is no stick, and absolutely no wiggle, lock rock, or blade play of any kind. The MP-1 is rock solid.

Blade centering is perfect on my knife.

Hinderer MP-1 – Final Thoughts

I like the MP-1 and can appreciate it for what it is. It’s high end pocket knife that is unapologetically overbuilt. This will only appeal to a certain type of knife enthusiast: one who appreciates overbuilt knives, and has a fair amount of disposable income. The thing is, the MP-1 has been beautifully executed. Some high end hard use knives are mere “me too” products that boil down to being janky rip offs. Here it’s obvious that quite a bit of thought and skill went into putting the MP-1 together. It may not be office friendly, but it’s beautifully made. It certainly isn’t a janky rip off.

Similar to the Eklipse, I don’t think the MP-1 will enjoy the success of the XM-18 series, but there was something oddly compelling about this knife. Sure it’s heavy and impractical for mere mortals like myself, but it will appeal to those seeking a full titanium Hinderer. And this is a more premium knife than the XM-18. There is extra work here. Extra detail. I obviously can’t speak for everyone, but it drew me in.

Perhaps the customizable nature of the knife will appeal to people as well. I never got into the knife customization thing, but there are guys that are really into that. Although Modifiedz hasn’t posted a video in years, people still seek out “knife pimpers”, and customized Hinderers regularly find their way onto the secondary market. Buying a Hinderer and then buying different hardware and handle scales to make it your own is a thing. The MP-1 could serve as a blank canvas of sorts and takes the concept of making the knife your own one step further.

If this was released a few years ago there would likely be a lot more fanfare. After all, this is a full titanium framelock flipper straight from the Hinderer factory. This is previously the stuff of legends. Even 3 years ago people would have crapped their pants for the chance to buy one at a knife show lottery. Today it’s another option if you are seeking out a high end folder. A lot more options have come onto the market recently, and while I think the MP-1 has been well done, I’ll be the first to admit that this knife is not for everyone.

[easyazon_block add_to_cart=”default” align=”center” asin=”B0773W7LPG” cloaking=”default” layout=”top” localization=”default” locale=”US” nofollow=”default” new_window=”default” tag=”brdfkdfk-20″]

I recommend purchasing the MP-1 at Knife Art, BladeHQ, or [easyazon_link asin=”B0773W7LPG” locale=”US” new_window=”default” nofollow=”default” tag=”brdfkdfk-20″ add_to_cart=”default” cloaking=”default” localization=”default” popups=”default”]Amazon[/easyazon_link]. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Spyderco Sage 5 Compression Lock C123CFCL Review

by Dan Jackson 23 Comments

I am sure a few people saw this review coming. When you consider my recommended EDC knives page, you can see that my general top 2 choices for someone is either the Spyderco Paramilitary 2, or the Sage 1.

Buy the Spyderco Sage 5 at BladeHQ

Buy on Amazon

I arrived at this conclusion after handling and reviewing hundreds of knives. There are a ton of other great Every Day Carry (EDC) options out there, but if I had to just suggest 2 knives to any random person off the ~~street~~ internet I’d say go with a Para 2 if you want a bigger knife with a 3.5″ blade, or go with a Sage 1 if you want something with a 3″ blade. Granted this assumes you are willing to spend $100+ on a pocket knife.

The Sage 5 takes the unassuming footprint of the Sage series, a product line designed to celebrate knife locks and their inventors, and matches it with the beloved compression lock. People have clamored for a smaller compression lock knife for years, and Spyderco has finally delivered with the Sage 5.

General Dimensions and Blade Details

The Sage 5 has an overall length of 7.17″, a 3″ blade, weighs 3.1 ounces, and is made in Taiwan. At the risk of sounding like a broken record, I like this size of knife for EDC. It’s not too big, and not too small. Compared with the Sage 1 this knife is a little lighter and thinner thanks to nested and heavily milled out stainless steel liners. The Sage 1 weighs 3.2 ounces, so only .1 of an ounce more, but it feels heavier in hand. I hate to use the “P” word these days, but I still think this may be the perfect size EDC knife for my purposes.

Like all the other knives in the Sage series, this knife features Spyderco’s leaf shaped blade. It’s simple and unassuming with its full flat grind and satin finish. The blade is ground from 3mm thick stock, and the end result is a blade that is thin and agile. It easily tackles cardboard, food prep, and mail. It will press into harder tasks if necessary. The tip is a reasonable balance of strength and precision. No surprises and no complaints with the blade.

Spyderco went with CPM S30V blade steel. This is the same steel they have used on the other Sages I’ve handled. I think CPM S30V is good, but these days I would prefer to see Spyderco upgrade this to S35V. S35VN is tougher and I find it a little easier to sharpen. S30V can be brittle, and it can be relatively tough to sharpen. The heat treat can make a difference, but all things equal I think S35VN is a nice little upgrade of over S30V.

That said, the S30V here is plenty good and I have a lot of experience with it. The blade is relatively easy to sharpen, exhibits good edge retention, and is decently tough. As always, for more information on blade steel I invite you to check out my page on knife steel or I suppose you could re-read this section on my Sage 1 or Sage 2 reviews. The blades and steel are all identical.

Handle, Ergonomics, and Pocket Clip

The handle design is where we begin to see the uniqueness of the Sage 5. To the untrained eye you may not think there is much different from the original Sage 1. Sure, they share a similar faux carbon fiber cladding, but beyond that there are key differences to note. Specifically, the Sage 5 has nested stainless steel liners, while the liners of the Sage 1 are not nested. As previously mentioned, this results in a thinner and lighter knife. The Sage 5 has only 2 stand offs while the Sage 1 has 3. However, the Sage 5 does come with a sleeved lanyard hole, something I could live without. Also, the color of the carbon fiber veneer is slightly different from the Sage 1.

As you would expect, the fit and finish of this knife is immaculate. The handle is put together with the same eerie precision of all the other Taiwanese Spydies. If it wasn’t for the fact that someone wrote on the inside of the handle scales with a pencil, I would have not have guessed that a human hand touched this knife.

Like a lot of Spyderco knives that share this profile, the ergonomics are great. Just like the Para 2 and Dragonfly 2, you have a forward 50/50 finger choil. You also get a pleasantly jimped thumb ramp. It provides traction without being overly aggressive. The main portion of the handle easily accommodates a full 4 finger grip, while that finger choil gives you some extra options.

The Sage 5 comes with Spyderco’s wire clip. Ah, the wire clip. This is a love it or hate it thing. Personally, I love the wire clip. Here it is a bright stainless steel. My preference is for the black chrome version found on the Sage 1, but I must admit that this satin version looks nice with the rest of the stainless steel hardware. It reminds me of the Chaparral.

This knife carries like a slimmer and lighter Sage 1. That is to say, it carries pretty damn good. This is a knife you could carry with a suit or slacks if you wanted to. The fold over wire clip buries deep, and most people will probably mistake it for a pen. The Sage 5 is a knife you will forget is in your pocket.

Deployment and Lockup

Of course like all the other Sages the blade is opened with a thumb hole. It’s easy to access and the blade moves on phosphor bronze washers. No complaints there. However, I did run into a problem when trying to close the knife. The action was very stiff from the factory. I didn’t mind at first as I knew that my Sage 1 required a break in period due to its tight tolerances, but I became concerned when the action didn’t improve after a couple weeks of carry and a healthy application of Tuf Glide.

So I decided to take my Sage 5 apart to take a closer look and try to resolve the issue with the stiff action. The problem was that the blade would not shut easily, and I actually needed 2 hands to close the knife. Not ideal, especially when compared with the easy action of my Para 2.

I found that Spyderco used an industrial strength version of Loctite on this knife. I am glad I had my new WiHa drivers as I am sure my Husky set would have stripped out. It required a lot of force to crack the pivot open, but with a little patience and elbow grease I was able to get the knife apart.

I ended up adding a little more Tuf Glide and then re-assembled the knife. Everything came back together without issue and now the blade moves freely. I can now easily open and close the knife with one hand. I think the pivot was adjusted a shade too tight at the factory. If you run into this problem there is no need to take the knife completely apart. Just carefully adjust the pivot.

The compression lock works great here, now that the blade moves freely. For the uninitiated, this is not a “liner lock on the back of the knife”. This is a totally different lock that sandwiches the locking leaf between the tang of the blade and a stop pin. You can get a better feel of this from the picture. Spyderco claims this makes for a stronger lock, but I think the most significant benefit is that you can close the blade with one hand, and without putting your fingers in the path of the blade, much like an axis lock.

I was concerned that the compression lock might be a little figety on the small profile of the Sage, but it works fine. The lock itself is easy to manipulate and lockup is tight. This is a nice locking mechanism worthy of a spot on the Sage lineup.

Sage 1 vs. Sage 5

I am sure at least a couple people will be curious to get my opinion on whether I like the Sage 1 or the Sage 5 more. This was actually a lot harder than I thought it would be. Before I took my Sage 5 apart I would have said the Sage 1. It was just too tough to manipulate with one hand. Now that the pivot is loosened slightly and the knife has broken in, I really like the thinner and lighter Sage 5. It is very easy to manipulate with one hand and it carries even better than the Sage 1. As much as I enjoy the Sage 1, I gotta “keep it real” – I think the Sage 5 is an improvement.

Still, the Sage 1 will always have special significance for me. It was one of the first higher end knives I bought for myself, and I love the simplicity of the knife. It’s solid and perfectly made. I also appreciate the familiarity of the liner lock. The compression lock is great, but there is something very simple and comfortable about a liner lock. The Sage 1 is a great pocket knife and you can’t go wrong with it. But I do think Spyderco managed to make some improvements with the Sage 5. Neither will be leaving my collection. I’ll update the review if my opinion changes.

Spyderco Sage 5 Review – Final Thoughts

I am not sure a review of this knife was entirely necessary. Combining the footprint of the Sage series with a compression lock is a no brainer, and Spyderco executed this knife near perfectly.

In a perfect world I’d like to see S35VN and the pivot perfectly adjusted out of the box, but these are small quibbles on an otherwise excellent knife. I’m sure some might want a different pocket clip, but I love the simplicity and elegance of the wire clip. Sorry wire clip haters.

The Sage 5 will likely be a “must buy” for Spyderco fans, and a serious contender for anyone seeking a 3″ EDC knife in the ~$100 range.

Looks like I’ll have to make some room on my best EDC knives page. We have a winner.

Spyderco Sage 5 Prestige Folding Utility Pocket Knife with 3" CPM S30V Stainless Steel Blade and Black Carbon Fiber Laminate Handle - PlainEdge - Everyday Carry - C123CFPCL

High Performance: The Spyderco's Sage Series is a unique family of knives showcasing the innovative lock mechanisms that have helped define modern folding knife technology.
Designed to be Safe: The Sage 5 uses a compression Lock mechanism. This mechanism is substantially stronger than Linerlocks and its location allows the knife to be safely closed with only one hand without placing your fingers in the path of the edge
Dependable: Every Sage Series knife in the series features the same basic design parameters: a full-flat-ground, leaf-shaped CPM S30V blade, an ergonomic handle design with textured forefinger choil and thumb ramp, and wire clip.
Versatile: The Sage 5 is an extremely capable all-purpose cutting tool with skeletonized Stainless Steel liners nested into textured carbon fiber/G-10 laminate scales.
More To Love: The open-backed construction reduces the knife's weight and allows easy cleaning, while a reversible deep-pocket wire clip provides convenient tip-up carry on either side of the body.

I recommend purchasing the Spyderco Sage 5 at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Ka-Bar Jarosz Folder Review

by Dan Jackson 13 Comments

Last Updated: August 1, 2019
A couple things drew me to the Ka-Bar Jarosz Folder.

First, Ka-Bar doesn’t release a lot of folding knives. They are a knife company best known for their classic USMC combat knife, and have a reputation for being a traditional knife company with a lot of fixed blade designs.

Buy the Ka-Bar Jarosz Folder at BladeHQ

Buy on Amazon

Second, Ka-Bar chose to collaborate with custom knifemaker Jesse Jarosz. Jesse is a maker that I have heard a lot about over the past few years. I have yet to handle any of his designs, so I was excited about the prospect of checking out this collab with Ka-Bar.

What’s interesting about Jesse is his unorthodox handle designs and decision to focus on non-flippers. This may not have been remarkable a few years ago, but these days most custom knifemakers are producing flippers. It has gotten to the point where someone producing a knife that is not flipper has actually become novel. It’s kind of crazy when you think about it.

His folder for Ka-Bar is based on his popular Model 75. This is a no-nonsense function-over-form design that appeared to be a great candidate for a production piece. With that in mind I bought the knife.

General Dimensions and Blade Details

The Jarosz Folder has an overall length of 8″, a 3.5″ blade, weighs 5.25 ounces, and is made in Taiwan. This is a brute of a knife, with a thick blade and full steel liners. 5.25 ounces won’t pull your pants down, but it is substantial, and the Jarosz Folder is more of a weekend carry for me. Of course if you can get away with EDCing a bigger and heavier knife then this could be a daily carry.

The Jarosz Folder comes with your choice of a drop point or tanto blade. I went with the drop point, as that is my preference, and it seemed to hold truest to Jesse’s original Model 75. The drop point blade is simple. It is ground from near 4mm thick steel, and the blade has a saber grind. The knife came surgically sharp from the factory, which is always great to see. The edge is neat, but peters out a little towards the tip. Ka-Bar finished things off with a coarse tumbled finish. This is a durable blade shape. The thick stock provides strength, while the hollow grind allows it to cut efficiently.

Ka-Bar went with Aus8 steel here, which is par for the course for a sub $50 knife. Aus-8 won’t win any edge retention awards, but is fine for a beater blade like this. You probably know as well as I do that Aus-8 is tough, easy to sharpen, and corrosion resistant. It’s a good budget steel and Ka-Bar gives you plenty of it. I have used the Jarosz Flipper to for several projects, and have broken down a fair amount of cardboard with this knife. It slices well, stands up to hard use, and has proven to be a great work knife.

Handle, Ergonomics, and Pocket Clip

The handle is comprised of fiberglass reinforced nylon (FRN) scales over full steel liners. There is a partial FRN backspacer that straddles a lanyard pin.

Handle construction is solid, but not perfectly executed. My handle scales were slightly proud of the liners in some spots, and the edges of the scales are rough. It was odd enough for me to post an inquiry about this on BladeForums to see if others shared that issue, or if I was just unlucky.

The feedback I received suggested that I was unlucky. Jesse himself was kind enough to post in the thread and recommend that I loosen the screws holding down the scales and nudge everything in place, or send the knife in for service. Adjusting the scales worked, and the problem mostly went away. In retrospect this seems pretty obvious but I haven’t run into the issue before. That said, the edges of my scales still catch the skin of my fingers slightly; especially the scale behind the locking liner. It’s not unpleasant, and it actually provides a little traction. Also, it is not noticeable when using the knife.

Once I resolved the issue with the handle scales I began to appreciate the sensible ergonomics of Jesse’s design. This is a funky looking handle, but in practice it works well. The handle shape is comfortable, and provides plenty of space for a wide variety of grips and hand sizes. There is a row of toothy flat-top jimping on the spine of the drop point version, and the FRN handles provide traction without being abrasive. The slightly rough edges of the FRN scales provide additional grip.

The pocket clip is an adaptation from the custom knives, and is a spoon style clip with Jarosz’s geometric logo. The clip is right side only, but is allows for tip up or tip down carry. It is uncoated stainless steel, but appears to have been tumbled to make it less shiny.

The Jarosz Folder carries OK. This is a substantial knife. I found that the combination of lightly textured scales, heavy knife, and light spring tension of the clip meant that the Jarosz Folder would continually slide down towards the base of my pocket. I mostly wear shorts with V pockets, and prefer to keep my knives higher up on my pocket for concealment and ease of accessing my wallet. This knife required regular adjustment.

Deployment and Lockup

The Jarosz Folder makes use of dual thumb studs and teflon washers. The blade is heavy and the detent is strong. You can flick open the blade, but it takes a fair amount of force. This is not a knife for the weak thumbed. The action is smooth, but I am not a fan of teflon washers, and would prefer phosphor bronze washers here. I am also not a fan of the decorative pivot on this knife. It’s nice and large, but Ka-Bar does not include a tool to adjust it. I don’t see this pivot on Jesse’s customs, so I don’t know where it came from. The good news is that the blade centering is excellent so there was no need to adjust the pivot out of box.

This knife makes use of a stainless steel liner lock. The liner lock is substantial and it engages the blade about 50%. The end result is a sturdy lock free of play in any direction. Initially my lock exhibited a slight amount of stick, but it has broken in and smoothed out over time. This is a solid liner lock.

Ka-Bar Jarosz Folder Review – Final Thoughts

Although I have raised some quibbles about the Jarosz Folder I think the pros outweigh the cons and this is a great work knife. In a perfect world I’d prefer a stronger pocket clip, a pivot with “regular” hardware, and phosphor washers, but when you get this knife in hand and actually cut stuff with it the design really comes together. It’s comfortable like a good pair of leather boots. I may not care for some of the details, but can’t argue with the results.

This is also a substantial knife designed to take some punishment. This is a hard use tool, not a slim daily carry, and that is OK if you know what you are getting into. Not every knife needs to be modeled after the Spyderco Delica. The unorthodox nature of the Jarosz Folder is part of what I enjoy about it, but it has also made this a tough knife to review.

Despite the Jarosz being unorthodox, I still want to contrast it with some other offerings that sell for around $40. Cold Steel offers the Pro-Lite and Voyager. These are 2 AUS-8 and FRN handled knives that are also tough. The Ontario RAT I is another excellent choice at this price point with similar construction and materials. You can venture into the $50 price bracket and find gems like the Blur and Aus-8 American Lawman.

While there are plenty of options to consider at the crowded ~$40 price range, I think the Jarosz Folder will appeal to the right buyer. This is especially true if you are looking for tank like construction. I don’t recommend it if you are looking for a lightweight every day carry. It is not that kind of knife.

The execution is not perfect, but the design is solid. This is a successful collaboration, and a good introduction to Jesse Jarosz if you don’t have the coin for one of his custom pieces.

Recommended if you are interested in Jesse’s designs, and want a no-nonsense work knife.

KA7505-BRK Jarosz Folder

Country of Origin: Taiwan
Package quantity: 1
Product type:KNIFE
Package dimensions:5.25" (L) x 2.0" (W) x 1.0" (H)

I recommend purchasing the Ka-Bar Jarosz Folder at Amazon or BladeHQ.

Wiha 75992 System 4 Precision Interchangeable Bit Set Review

by Dan Jackson 6 Comments

When I was just starting out with collecting knives I was not super keen on spending money on knife maintenance stuff. I was into sharpeners and knife sharpening, but could never justify more than my Sharpmaker. This may have been a blessing in disguise as I can maintain my edges just fine with this setup, and I can freehand sharpen as well.

But I eventually learned that some things aren’t worth being cheap about. In my article 5 Knife Maintenance Tools Every Knife Owner Needs, I list a torx driver set as one of the tools. Specifically, I recommended the Husky 8 in 1 Torx set. You can pick this up for under $10 at Home Depot.

I found this worked for most of my needs. That is, until I stripped a screw on my Fantoni CUT Flipper. That was a $300 knife that I fucked up using a $7 tool. That’s a tough lesson to learn, and one I don’t want you, dear reader, to have to repeat.

I know I’m not the only one to strip the screws on their expensive folding knives. You see knives being sold with stripped screws all the time on the forums. Sometimes you can send the knife back to the manufacturer to be fixed, but I don’t really feel like sending my CUT Flipper to Italy. The better thing to do is not strip the screw in the first place.

One way to cut down on the likelihood of stripping a screw is to buy high quality drivers. Wiha is the gold standard for micro screw drivers in the knife world, and many other worlds that value high quality tools. These are precision machined and hardened bits, and they aren’t going to warp and strip like the cheap bits you buy at the big box stores and Harbor Freight. The only problem is that by their very definition they are expensive, and Wiha makes dozens of variations of their tools. It’s going to set you back some coin, and it’s going to be hard to pick out the perfect set.

I spent a couple evenings on Amazon looking over their offerings before settling on the Model 75992. In a perfect world, Wiha would make something exactly like the Husky 8 in 1, only it would be made by Wiha and sell for $25. Instead they had a bunch of different configurations that weren’t exactly what I wanted. I picked out the 75992 because it was a micro driver, had all the torx bits I needed (T3-10 plus a T15), a compact case to house everything, and then it also came with the added functionality of an extender, hex bits, Flathead bits, and Phillips bits. 9 times out of 10, my knives come with torx hardware, but it never hurts to have some precision flat head and Phillips bits, and maybe the hex bits will come in handy some day as well.

I am keeping my set on my desk with some my other knife stuff, so I didn’t need anything ultra light or portable. This set comes with a heavy steel case, ideal for a garage or a dedicated work space. The door to the case is held in place with a couple detents. When you open it, case door folds back onto itself and creates a stand. The folding case does a nice job presenting the bits, while the plastic insert keeps everything organized and in place. So far I haven’t spilled bits all over the floor. I also like how the case closes with a satisfying snap. That is a feature most knife guys will appreciate. This heavy steel case is not something I would want to EDC (Every Day Carry), but I never EDC’d my Husky set anyways.

So far these bits have worked well. No issues with stripping hardware, and the heads of the bits haven’t deformed. Wiha uses hardened CRM-72 tool steel. I couldn’t find much info on CRM-72. Apparently it is a steel exclusive to Wiha, which makes sense if you are going to be manufacturing steel tools. Anecdotally, people say it is similar to S2 tool steel. I’d be curious to learn more about the steel and what hardness they heat treat it to. No issues with rust or corrosion either.

This set includes a 4″ (100mm) extender. I don’t recommend it for knives, but it’s good to have for hard to reach places in other projects. The bits are not magnetized, and neither is the handle, so it’s safe to use on and around electronics.

I spent right around $40 for my set. $40 may seem like a lot for a set of screwdriver bits, but if you have high end knives and are serious about maintaining them then this is money well spent. I bought mine for personal use and long term testing, and expect this set to last a lifetime. I’ll update the review over time if anything happens.

Also, I would be curious to see what sets other people use, and whether anyone thinks there is an “ultimate” Wiha set for knife owners. I don’t regret the 75992, but admit that a set including hex, Phillips, and Flathead drivers is probably overkill if you are only buying these tools to maintain pocket knives.

Wiha 75992 System 4 Precision Interchangeable Bit Set, Torx, Slotted, Phillips, Hex Inch, ESD Safe Precision Handle, 27 Piece In Compact Box

Micro Precision Bits on 4mm Hex Drive
Hardened for Extreme Durability
Bits of Exclusive CRM-72 Tool Steel
Choose ESD Safe or Standard Handle
Handle uses Ball Retainer Not magnetic

I recommend purchasing the Wiha 85992 at Amazon. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Pohl Force Mike One Review

by Dan Jackson 4 Comments

Last Updated: July 31, 2019
I have lusted after the Pohl Force Mike One for years. I wanted one for years. For the uninitiated, Pohl Force is a tactical knife company owned by Dietmar Pohl, a long time knife collector, knife designer, knife enthusiast, and author of books on knives. I have met with Dietmar, and the USA distributors for Pohl Force a couple times at Blade Show.

Buy Pohl Force Knives at BladeHQ

It was hard to walk away from the Pohl Force booth without a Mike One in hand, and I eventually broke down and bought one. I’m glad I did. Even 3 years later this knife is still awesome and unique. It’s like a European Strider with its integrated G10 handle scale/backspacer, not to mention the unique profile and finish work. But I’m getting ahead of myself. There is a lot to consider with the Mike One and I’m glad to present this review, even if I’m a little late to the Pohl Force party.

General Dimensions and Blade Details

The Mike One has an overall length of 8.66″, a 3.74″ blade, weighs 5.64 ounces. The Mike One is made by Lionsteel Knives in Maniago, Italy. This is advertised as the “EDC size” Pohl Force folder, and it certainly seems to be EDC (Every Day Carry) sized next to the Foxtrot One, which is a massive knife featuring a 4.5″ blade and overall length of 10.25″.

This Mike One is still a formidable knife, but could be a good size for EDC if you are a police officer, military member, or anyone else who can get away with a larger daily carry blade. Personally, this is not a daily carry as I tend to favor knives in the 3-3.5″ blade range for EDC.

The Mike One sports a slender drop point blade with a high flat grind and swedge. This is a 5mm thick blade, which is quite beefy for a folding knife. While Lionsteel has done a nice job grinding the blade to a thin edge, this is still a stout blade with hard use in mind. The tip is formidable and there is plenty of cutting edge. It strikes me as a great well-rounded blade shape that could be pressed into a wide range of tasks.

My particular version of the Mike One is the “Outdoor” version with the stonewashed finish. There is also a black PVD coated “Survival” version. I favor this stonewashed version. The blade is still quite reflective despite the tumbled finish, and you can almost use it like a mirror.

Niolox is the de facto steel for Lionsteel’s outdoor focused blades, and it’s a nice choice on this Mike One. I have some experience with Niolox after extensively testing the Blackwater Grizzly 6 and Ursa 6. Niolox has proven itself to be tough, yet reasonable to sharpen and resistant to corrosion. I think it’s a great choice and I’m excited to have the steel in a folder. I consider it to be a good upgrade over something like D2, with improved stain resistance.

Handle Design, Ergonomics, and Pocket Clip

As I alluded to earlier on, this knife comes with a beautifully sculpted black G10 handle slab and backspacer. Just like on the Strider SnG, this is a single piece of G10 that forms both the backspacer and non-locking side of the handle. Lionsteel kicked the production values up a notch by putting finishing the handle with a grooved pattern and also machining a geared backspacer. An equally impressive titanium framelock and black chain ring bolt hardware add further detail and visual interest to the handle. They did an awesome job and in my opinion, the build quality and finish work is higher than on that of the Strider.

The 50/50 forward finger choil and dual thumb ramps offer the end user a ton of grip options. You can choke up on the blade for detail work, or choke back for leverage per the below picture. Regardless of how you hold the knife it always feels comfortable and natural. The milled handle and backspacer compliment the handle design nicely by providing good traction without being irritating. There is little jimping, and the knife is comfortable to use, even after extended heavy cutting tasks like carving and push cutting rope.

The Mike One features an oversize wire clip. Frankly I wasn’t aware of how much some people loathe the Spyderco wire clip. One commenter said that the Spyderco wire clip was “feeble” and that I was “feeble” for liking it. You gotta love the internet – that’s a strong opinion on a pocket clip!

At any rate, the Mike One’s wire clip is nothing like the Spyderco version, so if you don’t like the Spyderco clip you may like the clip on this Mike One. For starters, it’s a much stronger clip. The knife has great retention in the pocket between the tough clip and corrugated handle. This clip has some pant shredding potential, but it will never fall out of your pocket. While not a true deep carry clip, the Mike One still buries deeply and carries discretely thanks to the matte finish and stealthy nature of wire clips in general.

Despite this being a near 6 ounce knife the Mike One carries well thanks in large part to the sturdy clip. I occasionally forget I am carrying this one. I wouldn’t carry this in slacks, but for shorts, jeans, or work pants you will find that the Mike One behaves well in the pocket.

Deployment and Lockup

The Mike One makes use of a serrated thumb disk. Thumb disks are not my favorite method of deployment, but it works here. The thumb disk is removable, which makes the knife a 2-hand opener, and more appropriate in some of European countries. The action is slow and purposeful thanks to teflon washers. Again, teflon washers are not my favorite choice. I really would like to see phosphor bronze washers here, as I think the knife would open a little easier with them. The end result is that you have a knife that takes a fair amount of effort to open – especially when compared with the flippers of today. This is probably my biggest gripe with the Mike One.

This is a titanium framelock, and here we have no steel insert. Lockup is extremely secure, opening with a heavy “click”. There is no blade play in any direction. Nor is there any blade stick. As far as titanium frame locks go, I think this one has been well executed. The end result is impressive and tank like. The Mike One is all business, and that shows in the deployment and lockup.

Here is a shot of it next to my LionSteel TM1:

LionSteel did include their RotoBlock mechanism on the Mike One. The RotoBlock is an over travel stop that prevents the user from hyper-extending the lock bar, and it can also be twisted to lock the knife open. It’s an interesting feature, but not one I ever find myself using. It’s probably handy if you ever decide to test the limits of the Mike One. For regular guys like myself it will probably get in the way more than it will help. Blade centering is good on my knife. Not perfect, but pretty close.

Pohl Force Mike One Review – Final Thoughts

This review has been several years in the making, and I am glad to finally have one in the collection next to my Fantoni CUT Flipper and LionSteel TM1. This is another a unique and practical design that has been executed beautifully.

I prefer this smaller format to the larger FoxTrot One. I handled the FoxTrot One, and it’s almost comically large. While the Mike One is a more practical EDC than the FoxTrot One, I wouldn’t mind seeing something even smaller. 3.5″ blade is about as big as I will go for EDC, but I realize that Pohl Force is catering to more of a military and LEO crowd. So while this is more of a collectible for me than a daily carry, it is a fully functional knife and designed for use.

I also like how Pohl Force goes so far as to include an oversized zippered pouch, a “Zertifikat” of authenticity, and even a Tuff Cloth and a kydex sheath. Everything about the Mike One is top shelf, and clearly a lot of thought and care went into all aspects of this knife.

Although Pohl Force has ceased working with dealers effective June 2016, you can still find Pohl Force Knives at BladeHQ or possibly Amazon. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.