g10

Benchmade 485 Valet Review

Last Updated: February 2, 2019

2013 and 2014 marked pretty quiet years for Benchmade. Not a whole lot of interesting stuff rolled off their shelves. The Volli was my favorite and has proven itself to be an excellent knife. Beyond that there wasn’t a whole lot to report.

Buy the Benchmade Valet at BladeHQ

Buy on Amazon

Benchmade’s 2015 SHOT Show releases actually looked pretty strong. The 485 Valet was one model that caught my eye. Perhaps most surprising was that the knives became available about a week after the show. Gone are the days of lusting over pre-production tools at SHOT only to find them released sometimes years later. Initially I was going to hold off on acquiring a Valet, but all it took were a couple positive affirmations from Tony regarding his knife and I had a Valet en-route to my office.

General Dimensions and Blade Details

The Valet has an overall length of 6.69″, a 2.96″ blade, and it weighs 2.18 ounces. The knife compares favorably to the Benchmade Mini Griptilian although it’s much sleeker. The low profile handle and spear point blade were innately appealing. This is a slim every day carry (EDC) piece that easily doubles as a gentleman’s folder with a more modern flair.

The Valet’s packs plenty of cutting edge, a high flat grind, and a sturdy tip all into a sub 3″ blade. The blade is ground thin and it almost cuts like classic slip joint (not a bad thing). I had no trouble zipping through boxes, bags, and all the little stuff that comes across my path. Everything from sliding between the folds of an envelope free a cable bill to de-boning chicken thighs for a stir fry.

Benchmade went with Bohler M390 stainless steel for the Valet. I have been putting M390 through its paces between this Valet and my ZT 0620. Heat treated to 60-62HRc, M390 is a super steel with superior edge holding abilities, yet it is still easy to maintain. I have been putting the Valet through it’s paces, and I’ve been happy with the results. I sliced up a big stack of cardboard in an informal “cut test” and managed to wear the edge down a bit after a while. I ended up sharpening the knife on the fine stones of my Sharpmaker. After just a few passes I could tell the edge was coming back, and I was able to quickly restore the edge to hair shaving, paper slicing performance. M390 is also very corrosion resistant.

M390 is apparently very expensive (on a podcast Tony and I determined that it appears to sell for 3x as much as a more normal steel). Given the option I would have selected a S30V or 154CM version if it meant a substantial reduction in purchase price, but I appreciate that Benchmade is interested in offering a premium product.

Handle, Ergonomics, and Pocket Clip

The Valet has a sleek gray handle with smooth G10 over milled out stainless steel liners, and a gray G10 backspacer. Handle construction is typical Benchmade quality. The G10 is contoured (3D machined) has been nicely finished. The steel liners are flush, and the backspacer sits solidly in the middle. I like the gray. It’s different, but nothing crazy. This isn’t a big handle, but it’s well made.

The Valet is a small knife and it feels like a small knife. I’m able to get a full grip on it, but there isn’t much room beyond that. It’s perfectly fine for little EDC tasks. There is no jimping, or much in the way of notable ergonomic features. The little knife sits in your hand well enough, and is more than adequate for normal use. I did not find the smooth G10 to be “slippery” and did not have any issues using the knife normally.

The pocket clip is a nice stainless steel deep carry clip. It buries almost completely into the pocket and is discrete. The handle is drilled and tapped for ambidextrous tip up carry. I like this clip and I think it works well.

The Valet also carries really well. At under 3 ounces and you quickly forget the knife is in your pocket. Perfect as either a discrete primary EDC or a lightweight backup knife.

Deployment and Lockup

This is an axis lock knife, with thumb studs. Usually, that would be all I need to hear, but I am concerned that this time Benchmade may have tried to do too much with too little. The positioning of the thumb studs and axis lock feels cramped. The axis lock is smaller than on other axis lock knives, and the thumb studs sit very close to the handle. The knife looks cool, and it certainly works, but it isn’t the most comfortable knife to open and close repeatedly. I’ll be curious to see if anyone shares that opinion with me.

Lockup on my knife is good. Out of the box there was a tiny bit of horizontal blade play, and a little more developed after a month of use. Pretty much all of my axis lock knives have a little play in them unless I tear them down and loctite the pivot. I know some people aren’t fans of the axis lock (too many moving parts and small springs to break), but I have always liked them. This one is smaller than I’m used to, but it still works.

Benchmade Valet Review – Final Thoughts

I am a little divided on the Valet. On one hand, it is a really slick little folder. I have been getting more and more into gents folders for daily carry, and visually this one ticks a lot of boxes for me. I like the smooth G10 handles, and the thin flat grind and spearpoint blade are excellent. My knife came well finished, and I didn’t run into any major QC issues that some folks have reported on first run Benchmades.

But a couple things turn me off on the Valet. The fiddly “landing gear” (small thumb studs placed very close to the knife and small axis lock) is my biggest concern. I would not recommend this knife for people with larger hands. I’m not Andre the Giant, but the position of the lock and thumb studs seems too tight for repeated use (or the mindless flicking open and closed of pocket knives while watching TV). Certainly this could be a “Your Mileage May Vary” thing. This is a beautiful knife, but I think BM leaned a little into far into “form over function” territory on this one.

I also think the price is also worth mentioning. $170 is a large sum for a small knife. I would have loved to see the Valet on the tail end of $150, and not on the tail end of $200. I realize that M390 is expensive material, and I think that folks who really appreciate a premium steel will have an easier time justifying the cost. Personally, I am not convinced this steel is worth the extra money.

But I don’t mean to end this review on a down note. The Valet potentially has a lot to offer. If it fits your hand well then there is little left to complain about. The Mini Griptilian is still my go to small Benchmade, but the Valet could be a worthy upgrade if it fits your hand and budget.

Benchmade - 485 Valet Knife, Drop-Point Blade, Plain Edge, Gray G10 Handle

HIGH-QUALITY: The M390 premium stainless steel blade offers exceptional cutting ability, wear resistance, and corrosion resistance. The G10 handle is durable, impervious to moisture, and stable under extreme temperatures.
WELL-DESIGNED: Benchmade's AXIS lock is exceptionally strong and fully ambidextrous. The 485 is a manual knife that can be opened and closed with one hand.
COMFORTABLE: The 485's lightweight design and contoured handle make it comfortable to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Valet 485's drop-point, utility blade style and all-around functionality make it ideal for everyday carry and use.

I recommend purchasing the Valet at Amazon and BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Cold Steel American Lawman Review

by Dan Jackson 27 Comments

Last Updated: March 9, 2018
When I hear the words “hard use folder” it’s often accompanied by a mental image of dollar signs. For whatever reason, we have equated hard working blades with titanium, super steel, and triple digit price tags. Those knives are cool, and I am sure some are capable of getting work done, but not everyone has that kind of cash – and even if you do it can be hard to really buy a knife like that and drive it like you stole it.

Buy the Cold Steel American Lawman at BladeHQ

Buy on Amazon

That’s why I like the Cold Steel American Lawman. For around $85 you get a rock solid knife that you aren’t afraid to beat on. After all, what’s the point of a hard use knife if you can’t actually bring yourself to hard use it? I have thrashed on my review sample for years. Lets take a closer look at one of my favorite every day working tools.

General Dimensions and Blade Details

The American Lawman has an overall length of 8-1/8″, a 3.5″ blade, weighs 4.5 ounces, and is made in Taiwan. This is a nicely proportioned medium sized folder designed by Andrew Demko. I found it reasonable enough for every day carry, but could definitely see this as a dedicated work knife or tactical blade. The “Lawman” designation seems to fit well.

The Lawman features a simple drop point blade with a high hollow grind. The knife is thinly ground, making it an aggressive slicer, and the tip is reinforced to hold up against hard use and thrusting. I like the blade shape. It’s not as aggressive as many of Cold Steel’s other offerings but is still very useful. There is plenty of belly, the tip gets nice and sharp, and the knife generally cuts really well.

Originally, Cold Steel used AUS8a for the blade steel, which is basically the same as AUS8. AUS8 is known as a softer steel and a lot of people don’t like it. I like AUS-8 because a couple swipes on a Spyderco Sharpmaker restores the knife back to hair shaving sharpness.

In 2015 Cold Steel updated their lineup of knives to include CTS-XHP steel, an American stainless steel forged by Carpenter. This is a superior steel to AUS-8, although it adds approximately $30 to the price tag of the knife. I have experience with CTS-XHP with other knives, and have had hands on experience with the Cold Steel Ultimate Hunter in CTS-XHP. CTS-XHP will hold an edge longer than AUS-8, and it is still easy to sharpen.

Cold Steel also upgraded to blade coating from a cheap black teflon coating, to a high end DLC coating. DLC is probably the best coating there is, so it’s a great upgrade.

Handle, Ergonomics and Pocket Clip

The handle of the American Lawman is made primarily of two thick pieces of black peel ply G10. There are no liners of any kind inside the handle and the G10 screws directly into a black aluminum backspacer and stainless steel lock bar. In practice the handle is quite strong. The G10 is thick and I was not able to flex the handle at all – so I would not worry that this handle will not be up to hard use. Fit and finish is nice too. All of the edges have been nicely rounded and everything lines up well. This is a strong and well put together handle.

I really like the ergonomics of the Lawman. The handle is plenty large and allows for a comfortable grip. There is some shallow jimping on the top of the handle. It’s not aggressive but provides some texture and feedback for your thumb. The G10 is extremely high traction and provides a good deal of grip. One of my favorite ergonomic features is the forward choil. Much like the Spyderco Sage or Paramilitary 2, this forward choil allows you to choke up and really get some detail work done. I am a huge fan of the forward choil. Cold Steel usually doesn’t include this feature so I think it’s worth mentioning. Finally I want to say that the knife also feels comfortable in a reverse grip.

The pocket clip is standard fare for Cold Steel. It’s small black coated stainless steel clip. It’s very tight. The tight clip combined with the aggressive G10 means it can tear up your pants if you aren’t careful. The clip is reversible (they actually include 2 clips since it’s a curved design) and it allows for tip up carry only. In pocket the American Lawman carries well. The small clip buries the knife deep, so it’s a discrete carry, and the slim profile and relatively light weight makes for an easy carry.

Deployment and Lock

The CS Lawman uses a thumbstud and a half to get the blade out of the handle. The thumbstud is not entirely ambidextrous out of the box, but it is swappable. This is not the fastest deploying knife and it will require some wrist action if you really want to snap the knife out. This is mainly due to the strong backspring of the triad lock. I don’t mind the slow and purposeful deployment of the American Lawman, but if you are one to habitually flick your knife open and closed the Lawman be advised that this isn’t really that kind of knife.

The lock on this knife is quite interesting. It uses the Cold Steel Triad locking system. The Triad is a modified lock back system that utilizes a “stop pin” to redistribute pressure placed on the knife and lock and in theory it provides for a stronger lock. My experience with the Triad lock suggests that it is in fact very strong. Lockback knives are very strong in general and the Cold Steel version is at least as strong as a regular lockback. I like how this lock is designed to break in with the knife so it won’t require maintenance. The lock feels very crisp and nice and secure.

American Lawman or the Recon1 or the AK-47?

Chances are, if you are interested in the American, you may also be interested in the Cold Steel Recon 1 or the AK-47. If that is the case, I recorded a video where I do a detailed comparison of these 3 models that you may find useful.

Cold Steel American Lawman Review – Final Thoughts

If you are in the market for a hard use folding knife and have around $50 to spend, the American Lawman should be on your short list. This is an extremely rugged knife that feels good in hand and is capable of some serious cutting. The relatively light weight design and non-threatening blade make this a good choice for EDC, although the knife could definitely flex into a more “tactical” role. No doubt this is why Cold Steel has marketed the knife toward law enforcement.

The biggest gripe with this knife was always the sub-par AUS-8 blade steel and cheap teflon coating. Cold Steel blew those complaints out of the water, when they upgraded this knife to CTS-XHP and a DLC coating. At this point, the only grievance I can raise is that the pocket clip can be a little small / tight for some. It’s not my absolute favorite clip, but it’s not that bad either.

All said this is one of my favorite folders from Cold Steel. They don’t make a ton of stuff in the 3.5″ blade length and the subdued looks really gels with me. I highly recommend the American Lawman if you need hard a wearing utility knife and don’t want to shell out a ton of cash.

Cold Steel American Lawman Black Folder

Blade thickness: 3.5 mm
Blade length: 3 1/2 inch
Handle: 4 5/8 inch long. G-10

I recommend purchasing the American Lawman at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Emerson Roadhouse Review

by Dan Jackson 11 Comments

Last Updated: August 5, 2019
I’ve mentioned a couple times before that every now and then I get the urge to pick up an Emerson, and make it my EDC. I know the knife is going to be too large for me to comfortably carry, and way overboard when I stop to consider my actual needs for a daily carry knife. But still, like a moth to flame I convince myself that this time things will be different as I hit the “buy” button on yet another Emerson. This is probably like a gal that brings home the guy with bad credit and a pack a day habit, thinking that she will “change” him to one day become the man of her dreams.

Buy the Emerson Roadhouse at BladeHQ

Buy on Amazon

Well this time around I have no such delusions of grandeur. I bought the Emerson Roadhouse not because I intend to carry it in the pocket of my skinny jeans next to my mustache wax and Starbucks card, but because I really dig the design and wanted to add it to the collection. I know the knife is going to be too big for me to actually want to carry and use, and I could care less.

At least this time around I’m being honest with myself. This is a beastly blade and I have always been drawn to the low slung modified tanto design. Frankly, it’s about damn time I reviewed the Emerson Roadhouse and I’m not going to apologize for it.

General Dimensions and Blade Details

The Roadhouse has an overall length of 8.90″, a 3.80″ blade, and weighs 6.2 ounces. This is a full size folder and was likely designed with law enforcement and military personnel in mind. I’m just a guy with a website and a day job, so my perspective on the knife will be limited to daily carry and use as a tool, rather than a defensive option. The design has proven popular enough for Emerson to roll the Roadhouse out in a variety of sizes. We have the regular (shown here) the Super Roadhouse (4.2″ blade), and the Mini Roadhouse (3.4″ blade).

The blade of the Roadhouse is a modified tanto and is one of my favorite shapes from Ernie. I’m not a tanto guy, but I really like this modified tanto. There is a little belly and something of a harpoon and swedge that give the knife some extra attitude. In the product description Ernie tells you to think about Jack Daniels and Harley Davidson’s. I can almost see Patrick Swazye in a dusty corner, the glint of the Roadhouse flitting through thick cigarette smoke and half empty bottles. Oh yeah. I really like this one. Mine blade is a two tone satin finish with stonewashed flats. Like all my other Ermersons, this knife is ground beautifully with a v grind and chisel edge. The blades are the best part of these knives although I see a fair amount of tooling marks on the spine around the wave and jimping.

The steel is tried and true 154CM. If it works why mess with it? I certainly don’t have a problem with 154CM, and Emerson has always done a good job heat treating it. People who actually use their knives will tell you that the chisel edge is ground on the wrong side for right handed users, but I don’t let that get in the way of a good time or a cardboard box. I have found the 154CM to be a serviceable steel, but if you don’t believe me feel free to read through my handful of other Emerson reviews.

Handle, Ergonomics, and Pocket Clip

The Roadhouse’s handle is standard black peel ply G10 over a titanium locking liner, and a steel non-locking liner. My knife has a thick partial G10 backspacer. I am pretty sure if you were to buy one new Emerson now offers their knives with standoffs over a backspacer. We have been trained to think that flow through construction is better, but there is something endearing about the G10 backspacer. The hardware is Emerson’s signature phillips head fasteners for the body screws and oversized slotted pivot. There are some tooling marks on the edges of the liners, but beyond that everything is nicely finished.

In hand is where the Roadhouse really shines. This is a full size knife and it provides ample room for all your standard grips. In addition to being a long handle, it’s also quite thick. Much like every other Emerson I’ve handled the knife is extremely comfortable. The black G10 offers plenty of traction, and the jimping on the thumb ramp holds your thumb but isn’t overly aggressive. If you can get away with carrying a big knife it’s hard to beat Emerson’s offerings from an ergonomic standpoint.

For the same reasons the Roadhouse feels so good in hand, it will be noticed in the pocket. It’s a large knife and there is no getting around that. Even small Emersons have a way of feeling big. The Roadhouse has been outfitted with Emerson’s standard black parkerized clip. It rides low, but not so low that you can’t access it easily. This is a proven clip design and is very comparable to Benchmade’s offerings. As always the knife comes drilled and tapped for right side tip up carry only.

Deployment and Lockup

For deployment you have a choice of thumb disk or wave feature. I’ve never been a huge fan of thumb disks. They always seem awkward to me. But they are low profile and stay out of the way when you are waving the knife open. The nylatron washers aren’t amazingly smooth, but they get the job done. I’d prefer good ole phosphor bronze, but this isn’t Burger King. I can’t have it my way. I can flick open the Roadhouse with a little effort, but for rapid fail-safe deployment the wave is the way to go.

For lock up you have a thick titanium liner. The locking liner is visibly thicker than the non-locking steel liner and I find that reassuring. Lock up on my knife is early and secure. There is a little bit of lock stick, but nothing bad. I prefer a steel locking liner over titanium, but it is what it is. Apparently Emerson’s warranty service is good if you manage to wear down the titanium. I have never had to use their warranty service personally.

Emerson Roadhouse Review – Final Thoughts

It’s big, it’s bad, it’s surprisingly expensive. I have always enjoyed the look of the Roadhouse on paper and am happy to report the knife looks just as good in hand. It’s a solid tool, with Emerson’s signature quirks. Despite some tooling marks on the back of the blade and liners, the knife has been carefully put together. The parts line up, the blade is centered, the lock doesn’t stick (badly) and everything feels sturdy and secure. The super nice blade and comfortable handle are high points. The steep price tag and impracticality of the knife (for my suburban purposes) are low points. Regardless, I am pleased to add this one to my collection and recommend the knife if you are a fan of Emerson’s offerings or if the allure of the Roadhouse is just too strong to resist.

Emerson Roadhouse – $227.66
From: BladeHQ

Emerson Roadhouse SF Plain Stonewashed Blade

I recommend purchasing the Roadhouse at BladeHQ or Amazon. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Fantoni CUT Flipper Review

by Dan Jackson Leave a Comment

Last Updated: August 30, 2019
We are in the midst of another Italian Renaissance. This time around it’s not a blossoming of politics and art, but of steel and titanium. The Italians are making some absolutely beautiful knives, and I can think of few examples that typify this as much as as the Fantoni CUT Flipper. At its core the CUT Flipper is a meat and potatoes knife. It is sturdy and well made, unpretentious, and intended for real use. Yet this knife has been elevated. The elegant design coupled with a fanatical attention to detail lifts the CUT Flipper from object to art.

Buy the CUT Flipper at KnifeArt

The CUT Flipper has been on my radar for several years. Carried by boutique purveyors and retailing for around $400.00, the CUT Flipper has eluded my grasp for some time. This is a collaboration between Fantoni and Dmitry Sinkevich, the same designer who brought us such things as the Zero Tolerance 0454 and many Shirogorov designs. The problem with the ZT 0454 and Shirogorov flippers is that you can hardly find them, let alone find them for a reasonable price. The CUT Flipper, while no means widely circulated, can still be found at retail (at least at the time of this article and for the past few years – Fantoni has never been known for high production volume). That places the CUT Flipper at a unique spot in the marketplace, and practically begs for a closer examination.

General Dimensions and Blade Details

The CUT Flipper has an overall length of 3.5″, has a 8.375″ blade, and weighs 5.3 ounces. This a larger knife meant for work. Some might call it a tactical knife. It’s obviously too big of a knife to carry around in an office setting, but it works fine with jeans and could certainly be an EDC item if you like carrying larger knives. There isn’t anything wrong with viewing this as a collectible either.

The blade shape of the CUT Flipper is an upswept modified drop point. I really love this blade shape, and I think it is part of the reason why I gave the Kershaw Turbulence such high marks. You have a high flat grind, swedge, and a neatly applied edge. The finish on this knife is very nice. It’s a high polish with a stonewash over it (or maybe a stonewash that was then high polished – hard to tell really). Regardless the blade has a deep luster that looks great and hides wear. It’s also a low friction finish, and it helps the blade slide through material.

Fantoni went with tried and true CPM S30V for their blade material. I have no complaints with the steel selection. I’ve had some issues with S30V in the past, but done right S30V is a proven steel. Here Fantoni has heat treated the blade to 60-61 HRc, and the knife takes a nice working edge that touches up easily on a strop or my ceramic rods. The CUT Flipper isn’t super thin behind the edge, but it thins out enough to be a capable slicer. It’s a good compromise between strength and agility. The upswept tip is strong, but the steep angle means that it isn’t my first choice for clipping coupons or other fine tip work. All in all, the blade lives up to its namesake, and it performs if you are looking to put the CUT Flipper to work.

As an aside, I know that Renzo Fantoni, the founder of Fantoni Knives, is a big fan of super steels. Don’t be surprised if Fantoni ends up producing a limited run these in S125V or some other insane steel.

Handle, Ergonomics and Pocket Clip

The handle of the CUT Flipper has a lot of really nice details – there is lot for a collector to admire here. 3-D machined slabs of G10 rest atop thick cut pieces of sandblasted titanium. All of the edges have been painstakingly radiused. At the end of the day construction appears simple, but that is only because they have pulled it off so flawlessly. I love the oversized hardware and how the backspacer was finished and slots around a lanyard pin. I’ll try to do my best with the pictures, but you really need to examine one of these in person to get a true feel for the workmanship.

In hand the CUT Flipper feels fantastic. It’s a larger knife and the handle is pretty thick, so those two factors add to this, but the slight pistol grip to the handle shape leave great spots for your palm and thumb. There is a a run of mild jimping that looks nice and serves its purpose, while the rest of the knife is devoid of aggressive texture. This knife feels natural in the hand and I had no problem breaking down boxes and carving up 2x2s with this.

The pocket clip is a simple bent titanium clip, and is given the same sandblast as the liners and laser engraved with Fantoni’s subdued logo. This is a small detail, but I like the choice of domed pocket clip screws – even they seem to be of very high quality. It is a sturdy clip that holds the knife steady, and reasonably low in the pocket. The handle is tapped for ambidextrous tip up carry, a nice nod to this knife’s utilitarian roots. At 5.3 ounces, the CUT Flipper is definitely something that you will notice in your pocket, but I don’t think the weight or the way the CUT carries is unreasonable given the size and construction of the knife.

Deployment and Lockup

The CUT Flipper is obviously a flipper style knife. If you prefer a non-flipper variant, check out the aptly named CUT. The flipping action on this knife is not something to write home about. You need to pushbutton (preload) the flipper to ensure a speedy and complete deployment, and that is a mild let down for such an otherwise fantastic knife. Still, the CUT Flipper is quite smooth and I still enjoy opening and closing it ceaselessly, periodically pausing to admire the blade or the gentle play of titanium and G10.

The CUT Flipper is a liner lock. The generous titanium liner engages fully and the blade locks up solidly and without play. It looks like Fantoni may have heat treated or carbidized the lock face, as there is slight discoloration in the last quarter inch of the liner lock – right where it meets with the tang of the blade. Performance of the liner lock is excellent and the blade centering is dead center.

Here is a shot of the CUT Flipper next to my Strider SnG:

Fantoni CUT Flipper Review – Final Thoughts

I can think of few folding tactical knives that have that holy trinity of form, function, and uber tight finish work. Some may argue that the “holy trinity” is just that: the Chris Reeve Sebenza, the Strider SnG, and the Rick Hinderer XM-18. Having owned two out of the three and handled several XM-18’s, I think the CUT Flipper belongs right next to these standard bearer blades. The CUT Flipper may not have the track record (or the marketing effort) of these other knives, but it certainly has the design chops, build quality, and functionality of these other knives.

This is a knife I have been drooling over for some time. Sometimes when that is the case I get a little underwhelmed when the actual knife arrives. Not so with the CUT Flipper. I think I actually like the knife more now that I have it. The CUT Flipper hangs with the best of them and has earned my wholehearted approval and recommendation. If you are at all on the fence about this knife, my suggestion would be to buy it with confidence. You will not be disappointed.

I would recommend buying the CUT Flipper at KnifeArt, as they are Fantoni’s only US dealer. However, their stock is limited.

I would also recommend purchasing the CUT Flipper at Amazon or BladeHQ, however, neither retailer seems to carry Fantoni Knives. Regardless, please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. Thank you very much.

Kershaw Injection 3.0 Review

by Dan Jackson 5 Comments

Last Updated: August 3, 2019
These days in the world of high value folding knives we have some pretty stiff competition. Old standbys like the Spyderco Tenacious and CKRT Drifter continue to be tough to beat while recent contenders like the ESEE Zancudo, Ontario Rat II, and CKRT Swindle are re-defining what is possible with a low budget folder.

Buy the Kershaw Injection at BladeHQ

Buy on Amazon

But when you are paying less than $40 a pop there is plenty of room for more, which is why my reinterest in budget blades has led me to the recently released Kershaw Injection.

Sporting a Todd Rexford design and lots of “custom” details, the Injection has the potential to be an all-star budget blade. But will it join the ranks of elite inexpensive folders or fade away into the shadows of obscurity? There is only one way to find out…

General Dimensions and Blade Details

The Injection 3.0 has an overall length of 7″, sports a 3″ blade, and weighs 3.30 ounces. This knife feels pretty heavy for a 3″ blade, but the Injection is still firmly in the EDC camp. For those appreciating a larger knife, Kershaw has thoughtfully decided to offer this model with a 3.5″ blade, aptly named the Injection 3.5. Everyone is a little different when it comes to their ideal EDC blade length, so I think that it is fantastic that Kershaw decided to offer this model in two sizes straight out of the gate.

The blade shape on the Injection is a very basic drop point. It may be a little boring, but it certainly works well with its fine tip and full flat grind. This is a very practical choice for EDC. One aspect that I don’t particularly like about this blade is the bead blasted finish. This inexpensive finish is prone to rusting and doesn’t look particularly good. I think it’s a misstep on a knife that is trying to appeal to the consumer based on it’s details, but I guess you can’t have it all at $30. Beyond the blade finish there is very little to gripe about.

The steel in this knife is 8Cr13MoV, a staple in low-end Chinese knives that I have spoken about ad nauseam. But don’t let my familiarity with the steel turn you off, I don’t mind 8Cr13MoV when the price is right. It compares well to AUS8 in that it won’t hold an edge forever, but it is durable and easy to sharpen. Despite being a stainless steel it can rust, and my particular knife did stain a little when I left it unattended on a shelf for a few weeks. You definitely want to keep an eye on this steel and apply a little oil if you are looking to maintain a totally rust free blade. All said, for a ~$30 folding knife it’s tough to beat 8Cr13MoV.

Handle, Ergonomics and Pocket Clip

The handle is where the Injection starts to get interesting. Taking center stage is the full G10 3-D machined handle scales. They feature a tasteful milled pattern and are subtly contoured. Intricately machined and 3-D sculpted handles are a feature often absent on $100 knives, let alone $30 ones, and this is the most impressive aspect of the knife. Further adding to the custom flair is the oversized decorative pivot and milled G10 backspacer with inset lanyard pin (rather than a lanyard hole). These are undeniably great details in a budget knife, and it elevates the Injection from beater blade to something much more interesting. The handle construction is also very solid. There are no gaps or cracks and all the pieces line up well. Underneath the G10 scales are solid stainless steel liners. It makes for a very solid knife, but it does add weight to the little Injection 3.0.

In hand the Injection 3.0 feels just a little short. Maybe that is because this is a very straight handle, which means that there is less surface area, but I found my fingers a little cramped. Granted I do take a large glove, so please keep that in mind. I will say that the basic handle shape makes the Injection easy to hold in a couple different positions and I didn’t notice any hot spots. Reverse grip is actually super nice with the angular shape of the pommel, but I can’t say I’ve actually used the Injection with a reverse grip yet. The entire knife is free of jimping which is fine for an EDC knife. This is a relatively thick knife and it fills the hand and has held up under harder use. If I were intending to use this knife for serious work I would opt for the larger version.

The pocket clip is simple, but it is also tasteful and well executed. The innocuous triangular clip is sure to appeal to a broad crowd, and it is positioned for decently deep tip up carry. The clip has a bead blast finish which further adds to the discrete look. The clip is swappable for left or right side carry, but fans of tip down carry are completely out of luck. Personally, this is not an issue.

Deployment and Lockup

For deployment you have dual decorative thumb studs. Despite the interesting milled details on the thumb studs, they are still very easy to access and quite practical. I had no problem flicking the blade open with the push of my thumb. Inside, there are metallic washers that appear to be phosphor bronze. This isn’t the smoothest knife I have handled, but if these are real phosphor bronze washers then the knife will only get smoother with time.

For lockup you have a sturdy stainless steel liner lock. My knife locks up 100%, but is free of any play. The liner lock is also easy to disengage and doesn’t stick. The full G10 scales and full stainless liners make for a robust knife that inspires confidence. Blade centering on my knife is favors the non-locking side, but it doesn’t rub and is acceptable for a knife of this price point.

Kershaw Injection Review – Final Thoughts

The Kershaw Injection is a solid attempt at a value folder with some high end details. The 3-D machined G10 scales, decorative thumb studs and pivot, and G10 backspacer are all high end finishes more commonly found on a custom knife than a Chinese production blade. But the off center blade, stiff pivot, and bead blasted finish bring us back down to earth. I also was not a huge fan of the weight and cramped feel of the handle. These are all minor gripes, and I realize you can only do so much with a budget knife, but I feel obligated to say something. While I like aspects of the Injection 3.0, it doesn’t make my list of recommended budget knives. There are definitely knives I prefer over the Injection at this price point.

Still, the effort Kershaw put into this one is apparent and the Injection is certainly capable as an EDC. The fact that I am even nit-picking a $35 folder shows that we are truly spoiled to have so many interesting and high quality budget blades at our disposal. Ultimately, this is a decent buy at $35 and I recommend it to fans of the design.

Kershaw 3820 Injection 3.0 Folding Knife

Liner lock -Thumb stud -Reversible pocket clip -Steel: 8CR13MoV
Bead-blasted finish -Handle: 3D-machined G-10
Blade length: 3 in. (7.6 cm) -Closed length: 4 in. (10.2 cm) -Overall Length: 7 in. (17.8 cm) -Weight: 3.3 oz. (93.6 g)
Liner lock; Thumb stud; Reversible pocket clip
Steel: 8CR13MOV, bead-blasted finish

I recommend buying the Injection at Amazon or BladeHQ. Thanks for checking out my review.

Benchmade Volli Review

by Dan Jackson 19 Comments

Last Updated: July 27, 2019
I’m not sure how to put this delicately, so I’ll just come out and say it: Benchmade hasn’t done a whole lot of exciting stuff in 2013, and it has resulted in a lack of reviews on new Benchmade knives. This isn’t necessarily a bad thing, but the lack of cool new stuff to examine makes for boring blogging.

Buy the Benchmade Volli at BladeHQ

Buy on Amazon

One 2013 Benchmade has been on my radar for some time, and that is the Volli. It hasn’t gotten a lot of attention, probably because it appears to be some sort of a rehash between the Griptilian and Barrage, but again that isn’t necessarily a bad thing. And frankly there is a lot to like here. In the time I’ve spent testing out the Volli I’ve found it to be a very functional and practical knife. We sometimes overlook those qualities as the industry focuses more and more on big names and exotic materials, but I still think there is room in many people’s pockets for a robust EDC/tactical knife without a lot of frills or hype.

General Dimensions and Blade Details

The Volli runs the gamut from an urban EDC to a “tactical” pocket knife depending on where your needs and preferences lie. For me, it’s more of a nights and weekends knife than a true daily carry, but for many I’m sure it would do well as an EDC. It has a feature set that I would think appeals to the law enforcement / military crowd, and I’m sure Benchmade also had those types of users in mind when they put this knife together.

The drop point blade is clean and simple with a high flat grind, and fine tip. My model comes in a bright satin finish although they do offer a black coated version as well. The grind lines are crisp and the knife came wickedly sharp out of the box. This is a simple drop point pattern but it has been done right.

The blade is S30V, a steel that I haven’t always been a huge fan of despite it’s popularity and billing as a premium knife steel. In practice I’ve found that S30V has a reluctance to take a really fine edge, especially on a couple Spydercos that I own, and I’ve sometimes dismissed it as more trouble than it’s worth. Well, I’m pleased to say that whatever Benchmade did with the S30V on my Volli, they really did it right. This is one of the nicest S30V blades I have owned.

The Volli came screaming sharp out of the box, which is always nice, but more importantly I’ve been able to keep that screaming edge with some judicious stropping. The knife has proven itself to be a really capable cutter. As always, I did test this knife thoroughly. I went through a great deal of 1/2″ sissal rope without any problem – it was almost comical how easily it cut through the rope. Eventually the edge slowed down, but I was able to quickly bring it back with my strop. Same went for wood and cardboard – it cut large amounts of both with no problem. This is because of the relatively (2.5mm) thin blade stock and the nice lean grind. 2.5mm isn’t alarmingly thin but many EDC blades (like my Spyderco Sage 1 – also in S30V) comes in at 3mm. While some may find the thinner stock a turn off, I like it because the knife cuts, and it cuts damn well.

Handle, Ergonomics, and Pocket Clip

The handle of the Volli is G10 over full skelotonized stainless steel liners. Probably the first thing you will notice is the heavy texturing to the handle, but it’s also important to point out that it has a full plastic backspacer and you can’t access the pivot without taking off the display side scale. Construction is sturdy. All the parts line nicely while corner of the handle has been broken to accommodate your hand. There is a small unobtrusive lanyard hole and all the hardware is of the torx variety.

Ergonomically, this is a straight forward and practical handle design. Relative to something like the Griptilian this is a thin handle, but there is still plenty there to fill your palm and all the corners are nicely contoured. I found it to be comfortable, even under hard use. There isn’t any jimping, which is fine in my book. I was able to really bear down on the knife when carving and cutting and I didn’t notice any major hotspots. Much like the simple blade shape this is a practical handle, and I found it to largely be a pleasure to work with.

The pocket clip is Benchmade’s classic split arrow clip. This time it has been configured for ambidextrous tip up carry. The aggressive texture to the G10 means this knife will destroy your pockets if you aren’t careful (you will never find me carrying this with slacks), and that may be my greatest gripe. I understand that there is a fine line when designing a knife like this, and you don’t want something that offers no grip at all. Aside from the pant shredding texture the Volli carries well. This is a classic pocket clip and it holds the knife securely and discretely.

Deployment and Lockup

The Volli takes advantage of Benchmade’s axis assisted opening technology. It snaps opens quickly with the brush of a thumb. An assisted opening knife is mostly a novelty for me, but I can see the advantage if you are in a line of work where you really need your knife to open. Benchmade included a safety located on the back of the handle. It stays out of the way but can lock the knife in both the open and closed position, a nice feature when you have a tip up carry assisted opening knife.

For lockup Benchmade went with their trusty axis lock, a personal favorite. My knife came with a small amount of lateral play, and I had to tweak the pivot by removing the G10 scale. The covered pivot looks nice, but it’s a departure from the otherwise practical design and I’d be remiss to not consider it a problem with the design.

In addition to the axis lock there is a secondary locking mechanism on the spine of the handle. It allows the user to lock the blade in either the open or closed position. It’s not a bad feature to have on a tip-up assisted open knife. It’s unobtrusive and functional.

I have to say that after Michael commented on this post (see below) I both de-assisted the knife and I took the secondary lock out. I don’t proclaim to be an expert when it comes to disassembling knives, but I’ve taken down plenty. The Volli was a little tricky to take apart and the whole process took me the better part of a half hour. That said, if you are patient and don’t mind potentially voiding your warranty it shouldn’t be impossible. The knife works just fine without the spring and the safety.

Benchmade Volli Review – Final Thoughts

The Volli isn’t a show stopper. It isn’t the latest and greatest. It’s no ZT 0560 or Spyderco Domino as far as the “wow” factor is concerned. But I’m still pleased with the knife and it seems to fill a spot in Benchmade’s catalog. Detractors of the Griptilian’s plastic handles may have finally met their match, and I’m impressed with how nicely the knife cuts and feels in hand. The thinly ground blade is one of the best slicers I’ve handled in recent memory, and the S30V steel performed way better than I’m used to seeing out of S30V.

If I were designing it from scratch I’d tweak a couple things. I’d leave it so the pivot could be readily adjusted, tone back the texture slightly and (if it were me) remove the spring assist. But these are all pretty minor and subjective complaints that may not be relevant to your needs or preferences. While I’m not completely head over heels with the Volli, it is still a very nice knife, and I’d go so far to say that if you are someone looking for a robust folder in the 3.5″ blade category with S30V steel I’d put it above the Zero Tolerance 0350 and say it is very strong competition for the Spyderco Paramilitary 2.

It may not be a runaway blockbuster blade of 2013, but that isn’t because it’s a bad knife, it’s because it has been overshadowed by some very interesting and very adventurous offerings in a very competitive marketplace. If you are in the market for a sturdy high performance folder in S30V with a ~3.5″ blade, then the Volli is well worth your consideration.

Benchmade - Volli 1000001 Knife, Plain Drop-Point, Coated Finish

HIGH-QUALITY: The CPM-S30V stainless steel blade is extremely well-balanced, offering superb edge qualities and rust resistance. The G10 handle is durable, impervious to moisture, and stable under extreme temperatures.
WELL-DESIGNED: The Volli 1000001 features Benchmade's AXIS Assist mechanism. It can be opened and closed quickly with either hand.
ALWAYS READY: The 1000001's quick, one-handed opening makes it easy to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Volli 1000001's drop-point, utility blade style and all-around functionality make it ideal for everyday carry.
SERVICES AND BENEFITS: For information and terms regarding Benchmade's Limited Warranty and LifeSharp Service, please visit Benchmade's website.

Benchmade Volli – $153.95
From: BladeHQ

I recommend purchasing the Benchmade Volli at BladeHQ or Amazon. Purchasing anything through any of the links on this website helps support BladeReviews, and keeps the site going. As always, any and all support is greatly appreciated – thank you very much.