Brad Southard

Spyderco Positron Review

Last Updated: August 5, 2019
The original Southard Flipper was a landmark knife for the Spyderco. The company’s first flipper, and a collaboration with popular knifemaker Brad Southard, the Southard Flipper helped prove the flipper concept for Spyderco and set the bar for things to come. Subsequently Spyderco released the Domino, an in-house Spyderco design, and the extravagant Rubicon, an over the top high end collaboration with Peter Carey. But everything leads back to the Southard Flipper.

Buy the Spyderco Positron at BladeHQ

Buy on Amazon

The Positron is Spyderco and Southard’s second collaboration. At first glance it more resembles a piece of modern art than a knife, blending Brad’s primitive lines with gleaming steel and carbon fiber. But the simplicity to Brad’s design belies a refinement matched by few knife designers. The Positron was a knife I couldn’t help acquiring.

General Dimensions and Blade Details

The Positron has an overall length of 7″, a 3″ blade, weighs 2.6 ounces, and is made in Taiwan. This is a smaller and more gentlemanly offering than the original Southard Flipper. A 3″ blade is appropriate for most settings, and 2.6 ounces is feather light. However, at slightly over half an inch thick, the Positron is a chunky folder. I may be spoiled by my Boker Urban Trapper, but at first glance the knife seemed very thick – especially given the thin and slender blade.

Speaking of blade, the Positron shares the same hook-nosed profile of many of Brad’s designs. This time things have been scaled down, and the gently curved spine meets with with a gently curved edge. There is a slight belly and the entire blade is set on a slight negative angle to the handle. Spyderco went with a full flat grind, and the blade has been given a sparkling stonewash over a highly polished finish.

Spyderco chose CPM S30V for the blade steel. I am not wild about this decision, especially for a higher end 2015 release from Spyderco. I would have preferred S35VN or CTS-XHP, but lets no kid ourselves into thinking S30V isn’t capable of peeling apples or opening mail – which is most of what I have done with the Positron. I also broke down a ton of cardboard boxes. It performed well. The bitingly sharp blade combined with a thin grind blade and fine finish make the Positron a good slicer. The narrow blade and thin grind remind me of a traditional knife, and it is slicier than the hollow ground Southard Flipper or the Domino.

Handle, Ergonomics and Pocket Clip

The handle is where things start getting interesting with the Positron. Spyderco and Brad decided to nest skeletonized stainless steel liners into a full 3-d contoured carbon fiber handle with a low profile black G10 backspacer. The result is a dramatic yet understated handle. The carbon fiber has been left with a matte finish, and there are no voids in the carbon fiber. The end result looks simple, but only because it has been executed with such technical precision. The fit and finish is perfect on my example, and it makes for an impressive knife.

This is a smaller handle, and a number of smart design decisions make the most of it. The thickness and deep finger choil make the Positron a natural in the hand. There is a short run of jimping on the spine and backspacer. Both serve their purpose to index and secure the hand. If you are careful you can perch your index finger on the small forward finger choil and choke up. There is no texture on the handle, but that never bothered me. The matte finish of the carbon fiber is not slippery, and the Positron is comfortable for normal use.

The Positron makes use of Spyderco’s wire clip. I have come to enjoy it on a variety of my favorite Spydercos, including the Sage 1 and Dragonfly 2. This is one of the most discrete pocket clips on the market, and I can easily clip this knife to a pair of slacks without raising eyebrows from co-workers or shredding your pants. The handle has been milled for ambidextrous clip up carry.

As far as carry is concerned, the Positron is thick, but at 2.6 ounces I never noticed it. It carries discretely. I have enjoyed my Positron in the office and in the back yard. It’s a versatile tool that you quickly forget is in your pocket.

Deployment and Lockup

This is a rare Spyderco folder that doesn’t feature a functional thumb hole. Instead, you get a “trademark” thumb hole and a flipper as your sole means of opening the knife with one hand. The flipper is snappy and pops the knife open easily enough, but it’s still possible to “flub the flip” if you aren’t paying attention. I’d put the detent strength at a “6” on a scale from 1 to 10, with 10 being ZT 0454 thumb chafing tough, and 1 being totally non-functional. So it’s a good flipper, but not on par with a Zero Tolerance 0562 (which I might peg at an 8). There are caged bearings inside and the action is smooth.

For lockup we have a nested steel liner lock. The lock engages early and the blade is free of play. Being a steel liner lock, there is no lock stick either. I like the liner lock for a couple reasons: the knife is lighter than if it had a titanium frame lock, and it gives the Positron more of a gents folder vibe. It’s a nice change of pace from all the framelock flippers that grace these digital pages.

Readers have commented that the jimped lockbar is a little difficult to disengage, because there is no cut out on the show side handle scale. I must have fat thumbs, because I never had a problem disengaging the knife, but I see what people are saying. This is worth mentioning.

It is also worth mentioning that blade centering is perfect.

Spyderco Positron Review – Final Thoughts

The Positron is a solid offering from Spyderco. I think it carries the torch established by the original Southard Folder and the Domino and moves things into an interesting direction. This is a more refined knife making use of real carbon fiber, nested liners, and 3-d machined scales. The blade is thin, the knife is a good size for EDC, and it carries well. It’s not as wild as the Rubicon, and strikes me as something that I actually want to carry. As usual, fit and finish from the Taichung Taiwan factory is superb. I showed the knife to my dad and he commented that it shared similarities to his Kershaw Skyline, an interesting observation that puts the Positron in excellent company.

I also think the price is fair for what you get. Retailing for well under $200, it almost seems like an affordable Spyderco – a rarity in a sea of $200+ offerings. It’s not a value monster like the Urban Trapper, but it’s not highway robbery either.

The biggest con I can come up with is that the handle is a little thick. It’s comfortable in hand, and I don’t notice the knife in pocket, but at over half an inch thick it still looks thick. The lack of a cutout for the lock release is another potential con.

Ultimately, this is a beautiful knife, and a step in the right direction for Spyderco. I look forward to seeing how their line of flippers continues to evolve. I recommend the Positron to Southard and Spyderco fans, and for those wanting a discrete and refined daily carry blade.

Spyderco Positron Flipper PlainEdge Fold Knife W/3.01" Blade

Made of highest quality material
Manufacturer: Spyderco
Spyderco positron Flipper PlainEdge fold knife w/3.01 inch blade

I recommend purchasing the Spyderco Positron at Amazon or BladeHQ. Thanks for reading.

Southard Knives Tolk Review

by Dan Jackson 5 Comments

Midtechs. If there was a single thread that bound Blade Show 2015 together for me, that thread would be midtechs. Specifically, midtechs offered directly from custom knife makers.

Midtechs are nothing new, and have been in the knife enthusiast’s vernacular for several years now, although it is admittedly a fuzzy term to define. But at the 2015 show it seemed like any custom maker worth his salt had a mid tech offering of some sort, and whenever I gathered with fellow show-goers it seemed like everyone had acquired at least one midtech at the show.

I don’t think this is a bad thing. I think this is an attempt to resolve an interesting problem in the market. Custom “tactical folding knives” are as hot as they ever were, and still show no sign of slacking off. While the concept of production company collaborations with custom knifemakers is nothing new, it seems like the bulk of the profits go to the manufacturer, and depending on the collaboration the knifemaker’s design is limited by the budget for the production knife. In some cases the result can be spectacular, but the flip side is that the product might be a watered down design with sloppy fit and finish, and inferior materials.

The advantages of producing a direct to consumer midtech is that the knife is more accessible than a full custom, allows the knifemaker to exercise greater control over materials and production quality, and builds in a bigger margin for the maker by virtue of the offering being higher end and the lack of middlemen. In a typical collaboration model with a big brand the production company takes a cut, the manufacturer takes a cut, a wholesaler takes a cut, then a retailer takes a cut. There isn’t much meat on the bone left for the designer.

But now it is possible for a custom knifemaker to essentially private label high end production knives, and offer them directly to the consumer. 10 years ago the technology wasn’t there to make this a viable business model. Today, the midtech model clearly has legs, and you don’t need a crystal ball to predict we will only see more of these hit the market – especially as custom makers take their designs overseas and offer there wares at lower and lower price points.

I was not immune to the powerful draw of the midtech phenomena, and ended up walking off the show floor with this Southard Knives Tolk midtech. Let me start by saying that Brad is a hell of a guy, and was a pleasure to meet and deal with. His custom offerings are among the most popular at the show, and between that and his tremendously successful collaboration with Spyderco might make a lesser man aloof. Not the case with Brad. He was warm, approachable, and it was clear he was proud of this midtech offering. I am happy to offer up this review today.

General Dimensions and Blade Details

The Southard Tolk has an overall length of 8.75″, a 3.87″ blade, weighs 4.7 ounces, and is made in the USA. This is the second midtech offering from Brad, the first being the Avo. He is dubbing his midtech line the Performance Series. The Tolk is a big knife with it’s near 4″ blade. Definitely a bit outside of what I usually gravitate towards, but given the length of the knife I will say it is lightweight and manageable. This could be an every day carry (EDC) piece for some folks. For me it’s a collectible.

The hump backed blade of the Tolk is reminiscent of the Spyderco Southard Flipper, and has been given a high flat grind and a bright satin finish. Brad also offers the Tolk with stonewashed flats if you care for a little more contrast. Blade thickness is about 3.5mm, which is generous for a thin profiled folder. There is a decent amount of steel traveling out to the tip, and the blade is thinly ground. There isn’t much belly and I find that the Tolk is well suited to slicing.

Southard went with CTS-XHP stainless steel for the blade. This is a proven steel in my book and I am happy to see it on this premium offering. I must confess that my Tolk has not seen a ton of pocket time (or cutting time). It has held up well under the light use I have put it through.

Handle, Ergonomics, and Pocket Clip

The Tolk has a full bead blasted titanium handle. Subtle grooves have been milled into the face of the handle while deep lightening pockets have been milled on the inside. The hardware on this piece is especially interesting, with the show side featuring a decorative pivot and decorative hardware. The non-show side has a high domed pivot and oversize body fasteners. Rounding things out are blue anodized titanium standoffs. They compliment the lockbar stabilizer and thumb studs nicely. Fit and finish is everything I would expect from a high end custom knifemaker like Brad. The knife is highly refined.

I like the way the Tolk feels in hand. This is a generous knife and my fingers had no problem spreading out over the curves on the handle. Like a Cadillac sedan, there is room to spare, and the chamferred edges sink into your palm like a velour seat. The spine jimping stands in sharp contrast – literally – to the rest of the handle. It is aggressive and toothy. It is not as bad as the jimping on the SnG, but under sustained use it will irritate the skin. The jimping on the butt of the blade is even more aggressive, but since I rarely if ever use my knives in reverse grip I view it as decoration more than anything.

The pocket clip is relatively pedestrian compared to the rest of the knife. It is a simple bent titanium clip, and it integrates nicely with the handle. It is drilled and tapped for right side tip up carry only, and there is a recess milled into the handle like an XM-18 or Large Sebenza. The clip of the Tolk has good retention and is set up for relatively deep carry. It carries well in the pocket and is thin and manageable given its length.

Deployment and Lockup

The Tolk is equipped with both a flipper and ambidextrous thumb studs. The thumb studs are set close to the handle and I am unable to use them to flick the knife open. It is a good option for slowly rolling the blade open, but most people will be gravitating towards the flipper. And the flipper is definitely a good choice. The ceramic ball detent is dialed in and the blade pops open with a satisfying snap. The pivot is on bearings and the action is smooth.

For lockup, we have a titanum framelock. Like the Odino, the last framelock knife I reviewed, the Tolk bucks the trend of stainless steel lockbar inserts. I don’t have a problem with this provided that the titanium framelock works well, and I am pleased to report that is the case here. Lockup is early and solid. There is no blade play or lock stick to speak of. This is a titanium framelock done right. Rounding things out is a blue anodized titanium lockbar stabilizer. Blade centering is perfect.

Southard Tolk – Final Thoughts

The Tolk is basically everything I would expect from a high end midtech offering: top flight materials, exceptional fit and finish, and hand tuned details. The Tolk has all these qualities in spades. The packing is also worth noting. The knife comes in a foam lined embossed box and includes a certificate of authenticity signed by the man himself. This has been a fun knife to own and it is obvious that a lot of thought and care went into every detail of the experience.

Some scoff at the notion that this is “as close as you can come to buying a custom offering.” I think that subject should be explored on a case by case basis. The Tolk is obviously not a custom knife, but I think that in this case Brad has put a lot of time and thought into these. He and has apparently even created some of the parts (like the pivots). He was selling them personally, including each with a signed card of authenticity, and he was proud to do it. While this obviously isn’t a custom offering, in this case I believe it is a couple steps closer than a collaboration with a production knife company.

When I turn back to the practicality of the Tolk, the knife is a bit large and expensive to be a true daily carry for me, but I had a fun time meeting Brad at the show and walking away with something he had a hand in. Perhaps one day I will trade it in for something a little smaller, maybe even put the money towards a custom piece. Until then, this will be the closest I have come to owning a Brad Southard custom knife.

The Tolk is currently unavailable. If it were available I’d recommend purchasing it at BladeHQ or Amazon. I’d follow along on Brad’s website and perhaps he will release more models there. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Spyderco Southard Flipper C156GBN Review

by Dan Jackson 17 Comments

Last Updated: July 30, 2019
If you have been following the production knife scene the past couple years, then you know that titanium framelock flippers have gotten extremely hot. This has a lot to do with custom and mid-tech makers that often set the trends, which eventually trickle down into production knives. Larger companies have finally taken notice, and now they want their piece of the framelock flipper pie.

Buy the Spyderco Southard Flipper at BladeHQ

Buy on Amazon

This has resulted is something that Andrew and I refer to as the “framelock flipper arms race.” When Zero Tolerance released their 0560 model not too long ago, it upped the ante in terms of materials selection, build quality, and technology. ZT loaded their knife to the gills with features like a caged bearing system, 3D contoured handles, and even going so far as to pocket out the titanium to lighten the knife. The 0560 continues to be a technological marvel as far as the production knife industry is concerned, but other companies, including Benchmade and Spyderco, have stopped to take notice – to the point where both companies have released their first models featuring a flipper in 2012-2013.

In this case we have Spyderco’s addition to the framelock flipper arms race: the Spyderco Southard Flipper. They decided to damn the titanium torpedoes and embark on a high-end collaboration with acclaimed custom knife maker Brad Southard. Known for his practical and well engineered designs, Brad has slowly carved a name for himself since he started making knives full time in 2009. Brad subscribes to the ideology that form should follow function, and he ultimately believes that good design is a marriage of aesthetics and performance. Technology also plays a key role in his knives, and this collaboration with Spyderco is a veritable cornucopia of the latest and greatest. Unfortunately for the consumer the price tag reflects this as well, with the knife arriving with a whopping $399.95 MSRP.

Does the fabled Southard Flipper deliver enough bang for the buck to make it worth adding to your collection? How does it stack up to something like the ZT 0560? Lets find out…

General Dimensions and Blade Details

The Southard Flipper has an overall length of 7.96″, features a 3.46” blade, and weighs a solid 4.1 ounces. This is a jewel of a knife, beautifully manufactured for Spyderco in Taichung, Taiwan. Proud Americans may dismiss the knife offhand for having both a $250 retail price and the words “Taiwan” laser engraved on the blade, but I assure you the quality is 100% there. The knife is beautifully made and has a reassuring heft to it – made possible by thick slabs of steel, titanium, and G10.

As for the knife’s intended use, I mainly see the Southard Flipper as a collectible or high end EDC option. I have mostly been carrying mine on the weekends, as I find it a little too chunky to be paired with slacks in an office EDC. Your mileage will certainly vary.

The blade is a signature Brad Southard modified drop point design. Cut from a thick piece of Carpenter CTS-204P stainless steel, the profile swoops and slopes into an abrupt tip. The partial hollow grind terminates at a neatly applied edge, and the entire blade has been given the ever popular stonewashed finish.

CTS-204P is apparently the latest in a line of high performance steels from Carpenter. According to their data sheet this steel has been specifically formulated for high end cutlery applications. This is the part of the review where more sophisticated reviewers would spend a few moments to wax poetic about the chemical structure and technical merits of the steel, but I have neither the time nor the inclination for such diversions. Instead, I elected to simply start cutting stuff. Hey, at least I’m honest.

My knife came with an extremely sharp and aggressive edge. It almost reminded me of the M4 on my Gayle Bradley in how razor sharp and aggressive it was out of box. I actually moved to a new house in the middle of my testing phase, so the Southard Flipper got a chance to open up many cardboard boxes. It zipped through cardboard with alarming speed and efficiency. I decided at this point I wanted to try a more formal cut test to get a better feel for the knife and the steel.

I started out with a 6″ length of 3/8” sisal rope. I made cuts every inch. In some cases this is a difficult and painful test for me to get through. The Southard Flipper crunched through the rope without even blinking. It was one of the easier rope cut tests I have done, and the knife could have easily handled 2-3x as much rope.

I then moved on to some more cardboard boxes. The Southard flipper once again worked with impressive speed and agility as I cleanly cleaved a couple pieces of 3-ply commercial grade cardboard into confetti. At this point in the test I felt the edge could use some help, so I stropped it briefly. The 204p came back to factory sharpness with little effort – surprising considering how the blade has likely been heat treated to well over 60 hrc (Spyderco does not list the actual hardness of the steel).

I wrapped things up by whittling some 2x2s. It worked through the wood, but I was not super impressed with the carving performance of this knife. This shouldn’t be too surprising as the blade is 4mm thick and features a partial hollow grind. I found it was not the most efficient tool for cutting up apples either.

At the end of the day I was pleased with the performance of both the knife and the 204p steel. The steel is capable of taking an amazing edge, I had no issues with rust or corrosion, and the edge held up well. It’s a nice knife and is well suited for EDC tasks.

Handle, Ergonomics and Pocket Clip

The handle of the Southard Flipper is primarily comprised of titanium and g10. On the locking side you have a full titanium frame lock with a G10 overtravel prevention mechanism. On the non-locking side there is a brown G10 scale over a thick titanium liner. Everything is screwed together, and features flow-through (pillar) construction.

The knife is immaculately finished. The hardware gleams, every corner has been meticulously finished, and the knife feels like an absolute gem. The titanium liner has been drilled out to reduce the weight somewhat, but this is still a knife that I feel in my hand and in my pocket.

One thing to note is the asymmetry of the thickness of the handle; the non-locking side is noticeably thicker than the locking side. I am not sure if this was a conscious design decision, or if Spyderco was not willing to have the G10 side 3d machined like on the ZT0560. Since the knife is equipped with an internal stop pin and captured ball bearing system, it is necessary to have a metal liner of some sort. At any rate the asymmetry is interesting. In my video review I talk about the character of the knife and the odd juxtaposition of high end materials and meticulous finish next to the somewhat quirky and almost primitive design. I think it’s an interesting contrast, although I’m sure the asymmetrical handle will drive some people nuts.

Moving to ergonomics, I find the Southard Flipper to be extremely comfortable. A rope cut test is always a good workout for the handle of a knife, and hard carving / whittling can also quickly reveal hot spots and ergonomic issues. I found that the Southard performed fantastically in the rope cut, and was decently comfortable when carving. The knife is pretty thick and that chunkiness serves it well when putting some extra force behind the edge. The jimping on the spine of the blade is damn near perfect in my book. It’s got a little bit of traction without being obnoxiously sharp or painful. It’s just a comfortable knife.

In contrast, the pocket clip is a little underwhelming. Stylistically it looks cool, and is plenty sturdy / well made. However, I find it’s a little sharp on the tip, doesn’t exactly run with the lines of the handle, and doesn’t carry particularly well. I think a thick and heavy knife like this could benefit from a deeper carry clip. Although none of this strikes me as a deal breaker, I’ll openly confess that I feel the pocket clip is the weakest link.

Deployment and Lock

The more reviews I write the more I wonder how painfully obvious this section is. Of course what we have here is a flipper mechanism, and Spyderco’s first at that. I find it generally works pretty well.

When you have a firm grip on the flipper the detent is strong enough to easily pop the knife open. That said, I’ve flubbed the flip many many times, and wonder if an even stronger detent would be appropriate here. I’ll be the first to admit that this is me being nit picky, but on a knife of this caliber I might as well provide the entire story.

The knife does open nicely however, and the blade rotates smoothly around an over-sized pivot and caged bearing system. There is also the “trademarked” Spyderco thumb hole on the blade, but it’s impossible to use with your left hand, and a challenge to actuate with your right, so I find myself not having a whole lot to say about it.

Lockup is exceptional. My lock engages around 40-50%, and has been like that since the day I bought it. The lock engages easily, has no stick at all, and the knife is absolutely rock solid in every direction. The pivot must have some industrial strength [easyazon-link asin=”B0043EK14O” locale=”us”]loctite[/easyazon-link] on it, because I have been opening the knife obsessively for weeks and have yet to have a need to adjust it.

There is also a small g10 lock bar stabilizer inset into the framelock that matches the G10 scale on the opposing side. It looks interesting and does a good job of preventing the lock bar from over-extending. All said and done I am impressed with the lockup on this knife.

Spyderco Southard Flipper Review – Final Thoughts

So, Spyderco’s first flipper… did they nail it or fail it? I have to say, I like the knife a lot. Brad’s design is sexy and sophisticated, and the Taichung factory has once again produced an amazingly well built knife. Say whatever you want about overseas manufacturers, but the Southard Flipper is immaculately made.

The Southard Flipper also performs. It’s comfortable, balanced, and cuts nicely. I had a blast working through rope and cardboard. It’s not the keenest slicer, so chores like cutting apples and carving wood won’t be it’s forte, but overall the Southard Flipper is a capable tool.

If I had to point out the weaknesses of the knife, I’d say the pocket clip could use a little work, the flipper could benefit from a stronger detent, and I could live without the lanyard tube. Aside from that I find little fault with the knife. I will say once again that this is a heavier knife and in my pocket it is more appropriate for jeans or casual clothing – this is not a gentleman’s folder.

And lets spend a moment on the “value proposition” of the Southard Flipper. Some will balk at the $220 price tag, and I can appreciate that – this is an expensive knife, and it isn’t for everyone. But frankly, discussions about value don’t interest me much. Sure, I appreciate a good deal, and understand the value of a dollar, but much like a Chris Reeve Sebenza or a Strider SNG, we are looking at luxury items. No one ‘needs’ a Southard Flipper.

As someone who owns a wide range of folding knives I think the Southard Flipper will be well worth it to fans of high end Spydercos, and fans of titanium framelocks / flippers. It’s a beautiful knife.

And where does it stand next to the ZT 0560? Personally, I prefer the Southard. The 0560 is a cool knife, but I prefer the size of the Southard more and the knife has this wonderfully solid and well balanced feel to it. Practically speaking I find it more comfortable to cut with too. Sure, the 3D machining on the 0560 is nice, and it’s great to see the 0560 being made in the USA, but I still prefer the Southard more. Have an opinion? Feel free to leave it in the comments section below.

Spyderco Southard Folder G-10 Plain Edge Knife, Brown

Made using the highest quality materials
Tested for quality and durability
The most trusted name in you cutlery needs
Flipper blade opening device
CTS 204P hollow-ground blade

I recommend purchasing the Southard Flipper at Amazon, or BladeHQ. Purchasing anything through any of the links on this website helps support BladeReviews. As always, any and all support is greatly appreciated! Thank you very much for reading.