Recommended EDC Knives

Chris Reeve Mnandi Review

Last Updated: January 10, 2018
When I think Chris Reeve Knives, I first think of the Sebenza, their flagship blade. Then my mind wanders to the Umnunzaan, their amped up tactical offering. Only after sampling both of those knives did I take a genuine interest in the Mnandi. It was one of those knives that I knew that I wanted to check out, but would have to get around to it eventually. My guess is that frame of mind holds true for a lot of collectors, especially those getting into knives within the past 10 years like I did in the middle of the tactical knife boom.

Buy the CRK Mnandi at BladeHQ

And that is a shame because the Mnandi is a really nice knife. Before moving forward with this Chris Reeve Mnandi review, I need to disclose that my Mnandi was built in 2011. Chris Reeve has since made some subtle refinements to the knife. Most notably, the pocket clip has been changed to a hidden hardware design, and the blade steel has been upgraded to S35VN over the S30V model shown here. Finally, the nail nick has been changed slightly. Some prefer the old style nail nick show.

General Dimensions and Blade Details

The Mnandi has an overall length of 6.375″, sports a 2.75″ blade, and weighs 1.5 ounces. The knife is firmly in the EDC or gentleman’s folder segment. I carry mine to the office no problem and prefer it over a bulkier knife for EDC. It could easily fall into the collectible market given the wide range of inlays available, although I do believe that this is a knife that was made to be used.

The blade shape is a modified clip point design. I like the lean, aggressive profile of the blade, and the angular nail nick further accentuates that low slung profile. The short belly terminates at a fine upswept tip, and the hollow ground blade has been given a nice satin finish. Like the other CRKs I have handled, the spine is nicely rounded. This blade shape is fine for EDC, easily opening mail, breaking down packages, and taking care of other minor chores around the house and office.

Blade steel on this particular knife is S30V, although if you were to buy a Mnandi new today it would likely come in S35VN. I was surprised to get a little flak in my large Sebenza review for reviewing an old model of the knife with S30V instead of S35VN. Practically speaking there is very little difference between the two steels. At higher hardnesses the S35VN will be a little easier to sharpen, but beyond that most people won’t notice much of a difference. I found the S30V on this knife very easy to maintain. Chris Reeve Knives is known for heat treating their blades on the softer side to aid in ease of sharpening. I don’t have a problem with that when it comes to my EDC knives, but edge retention junkies would prefer a harder heat treat.

Handle, Ergonomics, and Pocket Clip

The handle of the Mnandi is where things really start to get interesting. The knife is available with a large number of exotic wood inlays and is even offered with mammoth ivory bark and bone. My knife happens to have an African Blackwood inlay. Underneath the wood scales is full titanium construction. One thing I never really noticed about the Mnandi until I got one in my hand is that the titanium is actually two-toned. The flats have been given a satin finish while the edges are media blasted. It’s a really nice detail. On the back side of the knife you have a very nice flow through design. There is a single decorative standoff and a stop pin.

The Mnandi is a small knife but the handle offers plenty of room for a full grip and the knife is surprisingly comfortable to use. The arced handle supports your fingers much in the same way the Spyderco Dragonfly does, and you have some excellent jimping on the spine of the blade as well. CRK really knows how to get jimping right. It’s not thumb-shreddingly aggressive, but it provides enough traction to keep you in the game. Between the wood onlays, titanium handles, and 3d machined pocket clip you have a decently thick and comfortable handle. I wear a large glove and for a small knife, the Mnandi really works ergonomically.

The pocket clip is one of my favorite details of the knife. It is a 3-D machined stainless steel clip. It buries the knife in your pocket, is very secure, is discrete, but also has a nice decorative element to it. I’ve reviewed well over 100 knives on this site, and this is definitely the nicest clip I have come across so far. Chris Reeve recently updated the clip, making it a hidden hardware (no visible screws) design. It’s impressive that they figured out a way to improve on this already awesome pocket clip.

With all that said, my favorite way to carry the Mnandi is in the little leather slip sheath it came with. I haven’t tried to hide my love affair with the Victorinox Alox Cadet, one of my all time favorite EDC knives. A big part of the reason why I like that knife is because it’s perfect for pocket carry. Well, the Mnandi is also great for pocket carry, and if you use the leather sheath it helps protect the knife from getting beat up in your pocket. I highly recommend buying the leather slip sheath if yours doesn’t come with one.

Deployment and Lockup

The Mnandi relies on a stylized nail nick for opening. Visually, the nail nick really suits the design, and it works fine for one hand opening too. It’s ambidextrous, and I am pleased to report that I can open the knife left handed without much trouble. The action on my knife is super smooth. Like all of the other CRK offerings, this blade rides on phosphor bronze washers, and it has a smooth, glassy action that I find extremely satisfying. This is what owning a CRK is all about. It’s also worth mentioning that the pivot hardware is all custom, with the Chris Reeve logo engraved on the show side, and a collared pivot on the other.

For lockup you have a Chris Reeve Integral lock. My particular knife locks up late, but it’s very secure and there is no stick or issues with it. There isn’t much else to say although I will mention that blade centering is perfect.

Chris Reeve Mnandi Review – Final Thoughts

The Mnandi is the third model I have sampled in the CRK lineup, but it may very well be my favorite. Everyone is different, but these days I really get a lot of mileage out of small EDC knives that I can pocket carry. The Mnandi is about as good as it gets in that department. This knife is perfectly executed, has a lot of interesting details, and has been very satisfying to own. I can’t think of much to complain about, although I fully appreciate that for many, the $375.00 price tag will be a non-starter.

It’s small and expensive, so I’m not saying this one is for everyone, but if you have any interest in the Mnandi do yourself a favor and buy one. I have really enjoyed mine.

Chris Reeve Mnandi – From $375.00
From: BladeHQ

I recommend purchasing the Mnandi at BladeHQ or KnifeArt. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

CRKT Swindle Review

by Dan Jackson 15 Comments

I have been on a bit of a high value folder kick recently, focusing especially on the $30-40 segment. I’ve neglected this part of the market over the past year or two, favoring fixed blades and higher end folders, but a good deal of interesting stuff has come out in the $30-40 arena, hence the recent reviews of the Ontario Rat II and ESEE Zancudo, and I have a few more in the works.

Buy the CRKT Swindle at BladeHQ

Buy on Amazon

While the knives I have handled at this price point are solid and very functional, they are somewhat formulaic, and have a heavy emphasis on being tools rather than design objects. There is nothing wrong with that, as many seeking out a $35 folder want a good tool knife, but something has to be said for interesting design.

That is definitely not the case with today’s knife, the CRKT Swindle. Designed by Ken Onion, the Swindle pays homage to the classic swayback jack pattern, but features many modern touches like 3-d machined handles, a flipper, IKBS, a framelock, and a very interesting pocket clip. Ken and CRKT have definitely pushed the envelope in what is possible with a $30 folding knife, and we are all the better for it.

General Dimensions and Blade Details

The Swindle has an overall length of 7.5″, has a 3.2″ blade, and weighs 3.3 ounces. The long thin design really stretches out the blade and the end result is a practical gentlemanly type folder that works well for EDC, but also stretches into dress knife territory as well.

The full steel handles (gun metal gray with a matte texture to look like titanium) give the knife some extra heft, but it is still very carryable. And while it isn’t a “tactical” knife by any means, the long narrow blade comes to a very fine tip. It’s plenty stabby and I wouldn’t want to be on the business end of it.

The blade is an elegant modified wharncliffe design. Again, it’s a throwback to the swayback jack pattern of yore, with a high hollow grind, neatly applied edge, subtle belly and needle fine tip. Out of the box the Swindle came screaming sharp and ready for work. The narrow blade is plenty capable when put up against cardboard, and it makes for an ideal letter opener at the office. I also used the knife with some success when breaking down a chicken carcass. The upswept tip requires some extra flexibility, but it is fine for detail work. I really like that CRKT went ahead and rounded the spine. That’s a high end finish that I really like. I also like how they went for a satin finish over a cheaper bead blast. It shows off the nice even grinds and is more resistant to rust.

CRKT offers the Swindle in 2 blade steels: 8Cr14MoV on this model with the plain handle scales, and 12C27 Sandvik on the more expensive grooved version. I’d prefer 12C27 on the plain handled version honestly, but this 8Cr14MoV isn’t bad for the price. Similar to AUS8, this is a proven steel found on other budget folders like the Spyderco Tenacious. It’s a softer steel but it sharpens easily, takes a nice satin finish, and holds a reasonable edge. At this price point it’s hard to find much else, and I do like how they give you the option of 12C27 if you want to spend a little more money.

Handle, Ergonomics and Pocket Clip

The handle is plain stainless steel finished gunmetal gray to resemble titanium. I love how the handles are 3D machined, and I am impressed with how well made this knife is. CRKT has all their product manufactured in Taiwan, and the Taiwanese manufacturers really have their act together. 3 screws hold the handle together: one for the pivot, one for the pocket clip, and one for the backspacer. The end result is very elegant. Even the lockbar cutout arcs gracefully, and when the knife is closed the blade tucks completely inside the handle. This kind of stuff you just don’t find on $30 folding knives. Compared to my clunky Tenacious, Ken Onion and CRKT have thrust the value folder into rarefied air.

From an ergonomic perspective the Swindle works very well for an EDC knife. The handle is large enough to accommodate a 4 finger grip, and the curved shape fits naturally in the palm. I’m not usually a big fan of jimping, but CRKT found a great balance of grip and comfort in the jimping on the spine of the Swindle. The jimping here very much reminds me of the jimping found on a Sebenza’s, and the rounded spine furthers the connection. If you throw the knife in reverse grip a second run of jimping on the backspacer catches your thumb nicely.

The pocket clip is quite unique, and is more something you would find on a pen than a pocket knife. It sits on the back of the handle, kind of like an extended backspacer, and is spring loaded to provide tension. I won’t go so far as to say it’s my favorite pocket clip (because it isn’t), but it works, and it fits well with the theme of the knife. No doubt this will be a polarizing point for some folks. I think it’s a bold touch on an equally bold knife, and it has been well executed and further distinguishes this knife.

Deployment and Lockup

For deployment you have a flipper on IKBS bearings. The detent is well tuned and the blade flies out with the push of a finger. The action is very nice. The flipper is a low profile design, but it’s jimped to provide a little extra traction. Again, CRKT has managed to find a sweet spot in cutting jimping that is practical without being over the top aggressive. I am still not sure if bearings are 100% necessary on a knife, but here it has been well implemented and I certainly am not complaining. The Swindle, with its relatively light blade, flips with the best of them.

For lockup you have a stainless steel frame lock. It locks up early and securely and I did not experience any play in my knife. Lockup has settled in right around 25%, which shows that they paid attention to the tolerances and geometry of the frame lock, and suggests that it will hold up for a long time. Blade centering is also dead perfect, which, while not a requirement on a $30 knife, again elevates the sense of pride of ownership, and my overall appreciation for this tool.

CRKT Swindle – Final Thoughts

I have had a number of really nice high value folders cross my desk these past few weeks. Knives that I enjoy and recommend. The Swindle is truly something else. Not only is it functionally a very solid knife, it has so many details and little upgrades that I find myself examining it from the perspective of a higher end folder. I haven’t loved all of Ken Onion’s designs, but this one truly deserves accolades. It’s outside his typical work, and has allowed him to showcase his talent as a designer. The pocket clip may not be “perfect” by everyone’s standards, but it works well in the context of the overall knife. Barring that I find very little to complain about the knife.

I decided to photograph my Swindle next to my Kershaw Cryo on purpose, to show what is possible for a $30 folder, and two steel framelock flippers at that. Both knives feature big name designers, but beyond that the knives quickly diverge.

With the Swindle you have a graceful and balanced knife, whereas with the Cryo you have a stubby little brick. The Swindle features a rounded spine and 3-d contoured scales, while the Cryo is slab built with sharp edges. With the Cryo you get an off-center blade and shitty assisted opening. With the Swindle you get a manual action knife with a beautiful detent and an IKBS bearing system. With the Cryo you get a coated blade, with the Swindle you get a nice satin finish. The Swindle is an exercise in minimalism and restraint, while the Cryo is pockmarked with holes and screws.

I don’t mean to turn this into Cryo bashing, after all, I felt that the Cryo was an OK knife for what it was (although disappointing in many respects). But next to the Swindle there is no comparison in my mind; the Swindle is a superior EDC knife, and CRKT has redefined what’s possible with a $30 folder.

The design of the Swindle may not be for everyone, but if the knife interests you at all I suggest buying it. I wish I jumped on mine earlier. Highly recommended.

Columbia River Knife & Tool Columbia R Swindle Knife COLUMBIA RIVER KNIFE & TOOL Swindle Folder, One Size

Fast Opening: IKBS ball bearing pivot deploys the blade fast
Brute Strength: Frame lock utilizes a thick lock bar to secure the blade
High Tech: Tensioned clip secures knife to the pocket
Designed by Ken Onion in Kaneohe, Hawaii
Limited Lifetime Warranty covers any defects in materials or workmanship, see company site for details

I recommend buying the CRKT Swindle at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

ESEE Zancudo Review

by Dan Jackson 32 Comments

Last Updated: September 30, 2017
By now most people are well acquainted with ESEE knives and their variety of fixed blade offerings. Hallmarked by their thick powder coatings, 1095 steel, USA origins, and unlimited lifetime warranty, I have grown to be quite a fan of ESEE products, and hold their Junglas and Izula II in especially high regard. ESEE is known for their no nonsense form over function tools, so it was quite interesting to see that ESEE was taking on a folding knife, and a sub 3″ framelock at that.

Buy the ESEE Zancudo at BladeHQ

[easyazon_cta add_to_cart=”default” align=”center” asin=”B00H83DBQ2″ cloaking=”default” height=”42″ key=”tall-orange” localization=”default” locale=”US” nofollow=”default” new_window=”default” tag=”brdfkdfk-20″ width=”120″]

The design of the Zancudo, which, by the way, is the Spanish word for mosquito, is unassuming enough. Whether it will live up to the legacy of their fixed blade offerings is an entirely different question.

General Dimensions and Blade Details

The Zancudo has an overall length of 7″, sports a 2.94″ blade, and weighs 3.1 oz. This is a great size for suburban EDC, although I don’t doubt it will do well at a camp site preparing food or performing other light camp chores. The sub 3″ blade is an interesting choice. There is plenty of room to gain a few extra millimeters so my guess is ESEE is trying to make a knife that flies under jurisdictions where 3″+ blades are outlawed. The full steel liner and steel frame lock add some heft to the knife, but it’s still slim and light enough to be an easy carry. In talking with globe-trotting renaissance man Kyle Ver Steeg on the podcast, I was surprised to learn that he prefers a small folder for most of his adventures. This could very well be an option for a trip to the Amazon, or disaster relief effort in the Philippines.

Your blade shape is a sloping modified drop point design. The spine of the knife droops down to almost a spearpoint, and the end result is a very utilitarian design with a thicker tip and relatively short belly. The blade is flat ground nice and thin, and the edge bevel has been neatly and uniformly applied. In practice the knife makes easy work of typical daily carry tasks like opening mail, cutting up fruit, and breaking down packages. A handsome dark stonewash has been applied for a well worn look right out of the box. The end result is an innocuous looking blade that packs plenty of punch for daily tasks. There are a lot of logos and markings on the blade. The mosquito on the back side is interesting; can’t say I have any other folders that share that distinction.

Blade steel is classic AUS 8, par for the course for any low price Taiwanese or Japanese made knife. I’ve said it before, I’ll say it again, AUS-8 is a relatively mild steel. Edge retention isn’t its claim to fame, but I have gotten plenty of work done with AUS-8, and it is extremely easy to sharpen and maintain. It’s also a very tough steel. For a sub $30 folder it’s a welcome choice.

Handle, Ergonomics and Pocket Clip

The handle on the Zancudo is so simple it is almost boring. It’s a form follows function kind of knife, and I don’t have a problem with that. On the show side you have a faux G10 scale over a full steel liner, on the lock side you have a tumbled stainless frame lock. The knife is of pillar construction and features a lanyard hole. One interesting detail is that the hardware on the locking side is stainless while the hardware on the non-locking side is black. This is a thoughtful and attractive touch. Thy could have easily gone with all stainless or all black hardware, so I like that they paid attention to this detail. It is also important to note that everything has been really well finished. There isn’t a sharp corner or unnoticed detail. Even the liner and inside of the frame lock has been polished to a mirror-like sheen.

While on paper the handle of the Zancudo looks a little goofy, in hand it all makes sense. Mike Perrin decided to stretch this handle out to afford the user the full length of the handle without a choil or large guard. The resulting grip is sure and comfortable, and the knife is ready for work. The very short run of mild jimping is perfect for indexing your thumb and providing some level of traction without chewing into your flesh. The plastic scale, while inexpensive and not my favorite feature of the knife, has been patterned to mimic peel ply G10. The results are understated, and you have traction without the trauma often associated with aggressive G10 handles.

The pocket clip is functional but has an almost Ken Onion-esque curvature to it. I think it may be some sort of OEM piece, as I could have sworn I have seen this clip on another knife. The bend to the clip is quite severe, and it results in very sturdy and secure retention. The fact that it butts up against smooth stainless steel will save your pockets and make this knife easy to access. The clip comes right side tip down but the handle is also ready for right side tip up carry. The Zancudo is nice and slim and I found it very pocketable. The extra weight isn’t really noticible on heavy denim, but there are lighter knives out there if watching weight is your thing. I think ESEE’s product line is ripe for a lightweight version of the knife, as that would likely be of greater appeal to the weight conscious hiking and outdoors crowd.

Deployment and Lockup

Much like my Rat II, a firm flick of the ambidextrous thumb studs will send the blade flying out, and the blade glides on phosphor bronze washers. The thumb studs are simple and easy to get at, the way thumb studs on this kind of knife should be. No complaints in the deployment department.

For lockup you have a steel framelock, and it is very robust and well implemented. Fresh out of the box I noticed a little blade stick, but that quickly calmed down and has been replaced by effortless rock solid lockup. Given how relatively thin both the blade stock and lockup are, I am impressed by the early (50%) lockup on this knife. That combined with the dead center blade provides a sense of pride of ownership that you don’t typically encounter with bargain basement blades.

ESEE Zancudo Review – Final Thoughts

Much like the Rat II, the Zancudo isn’t a particularly sexy knife, but it is practical, robust, and well made. You also can’t argue with the price. ESEE always manages to infuse a good deal of character with their knives, and I am happy to report that the trip overseas didn’t wash that character away. The tumbled steel, matching hardware, and big black bug on the blade all play a part in distinguishing this knife from the competition.

2017 Update: This is among my favorite knives in the $30 range, and it makes it to my best EDC knives list. Although I have always liked this knife, I didn’t come to this conclusion immediately. It was only after years of carry and use that I realized the depth of the Zancudo – how thoughtfully designed it was. It’s beautifully built for the money. I prefer it over the Rat II, and can think of little else that matches it at this price point. If you are on the fence about the Zancudo my recommendation is to buy it without hesitation.

[easyazon-block align=”center” asin=”B00H83DBQ2″ locale=”us”]

I recommend purchasing the ESEE Zancudo at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Ontario Rat II Review

by Dan Jackson 19 Comments

Last Updated: March 9, 2018

Not everyone who reads the site knows about this, but I do have a couple sections dedicated to knives I have reviewed and recommend. Of particular interest could be the recommended EDC knives section, and the recommended tactical knives section, as these types of knives are generally pretty popular. When browsing those lists there are a few special knives that make the cross over to both categories.

Buy the Ontario RAT II at BladeHQ

Buy on Amazon

Typically, these are gold standard blades like the Spyderco Paramilitary 2 and Benchmade Griptilian which are great knives, but clock in at $110+ and $70+ respectively. But then there is another category, the recommended high value knives section, where I try to limit the knives to $50 or less. It is quite rare to find a knife that can fall into all 3 categories. The Ontario Rat I is one of those knives.

I reviewed the RAT I a couple years ago, and I am still of the opinion that those seeking serious bang for their buck when it comes to a big EDC / “tactical” knives would be well served with a RAT I. That’s great for guys wanting a big knife, but what about the rest of us who are looking for a more pocket friendly EDC?

Enter the Rat II. It has everything we all know and love about the Rat I, but in a much more compact package.

General Dimensions and Blade Details

The Rat II is 7″ long, has a 3″ blade, weighs 2.75 ounces, and is made in Taiwan. This is a great size for urban EDC. It is both pocket and people friendly, and you still have enough knife to get some real work done. Of course, if you are looking for something larger then the Rat I has you covered.

The blade is a modified drop point design. Nothing about this knife is particularly sexy looking, but this plain utilitarian blade gets the job done. The full flat grind is thin, and the knife zips easily through all manner of material. The tip is plenty pokey for detail work while the bright satin finish is both attractive and corrosion resistant. They do offer the knife with a shiny black coating, but it is not very durable. I prefer the satin finished version.

Just like the Model I, the Rat II comes in AUS 8 blade steel. Steel snobs may turn their nose up at AUS 8, but my own testing and use has proven again and again that AUS 8 takes a great edge, is super easy to maintain, doesn’t chip out easily, and resists rust and corrosion. For a $30 folder, AUS 8 is about as good as it gets.

Handle, Ergonomics, and Pocket Clip

The handle on the Rat II features the same robust design of it’s bigger brother. You have plastic scales over full stainless liners with pillar (or “flow through”) construction. It is simple and effective. I also like the choice of handle colors and the black hardware. This knife is made in Taiwan, and like many of the other Taiwanese knives I have handled, this knife features exceptional fit and finish. One nit pick is that the handle scales are plastic. I would prefer some G10, but some corners have to be cut when your are targeting the under $40 market.

From an ergonomic standpoint the Rat II is pretty good. Obviously it’s not going to be as comfortable as the oversized Rat I, but, given the size of the knife I was still able to get a nice grip on it with my larger hands. Extra large hands may run out of real estate, but you could always choke up near the ricasso and gain a little extra room. The plastic scales are comfortable. All the corners have been rounded, and a texture provides some feedback without being aggressive. The jimping on the other hand is pretty aggressive. Under extended use this jimping definitely bites into your thumb, and I don’t like that aspect of the knife. All said though, and this is a decent knife to work with.

The pocket clip is a classic shape (think Benchmade or Emerson), comes with a painted satin black finish, and can be put on any of the 4 corners of the knife. It’s simple, discrete, and totally functional. The painted clip does show wear easily, but this is a user so I don’t mind. In pocket the knife rides low and stays where you want it to. I really cant complain about its simple and utilitarian design.

Deployment and Lock Up

For a low end knife the Rat II is surprisingly smooth. The Aus 8 blade glides on sintered bronze washers. A gentle nudge of the ambidextrous thumb studs sends the blade cascading out with a satisfying “thwack”. The blade on my knife came perfectly centered, which adds another level of enjoyment to the knife.

For lock up, you have a robust liner lock. This is a beefy liner lock, and there isn’t even a suggestion of play when I tug the blade in any direction. This is a great choice for hard use tasks, and I don’t hesitate to use this as a work knife. In fact, it’s a great choice for those nasty jobs you don’t want to risk a more expensive knife with. The blade locks up tight and the lock bar disengages easily when you need it to.

Ontario Rat II Review – Final Thoughts

For the money the Rat II is a hall of fame blade that makes my lists for both recommended EDC and recommended high value knives. It may not be the prettiest pony in the stable, but if you subscribe to the philosophy of function over form, want a folding knife with a 3″ blade, and have around $30 to spend, then the Rat II could be just the knife you are looking for. My biggest gripes were about the plastic handle scales and aggressive jimping. Beyond that I find very little to complain about, and these are easy objections to overcome given the price.

Just like it’s big brother, the Rat II is a no-nonsense tool ready to provide years of service.

Sale

Ontario Knife Company Rat II, Satin AUS-8 Stainless Steel Drop-Point Blade Folding Pocket Knife, Black Nylon Handle Liner Lock Knife, Everyday Carry Knife – ON8860

secure: the ambidextrous handle features textured black nylon 6 scales with an open-built steel linerlock frame
comfortable: the rat-2 knife is a handheld size designed for comfort and performance making it ideal for everyday carry
dependable: quick and easy access with dual thumb studs and a 4-way reversible pocket clip
"durable: the rat-2 comes equipped with a 3" plain edge blade made of reliable aus-8 stainless steel as well as a textured nylon handle"
"convenient size: the 4. 1" closed length handheld size is ideal for every day carry and fits in the hand and pocket comfortably"

I recommend purchasing the Ontario Rat II at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Chris Reeve Knives Large Sebenza 21 Review

by Dan Jackson 29 Comments

Last Updated: July 28, 2019
For many the Sebenza 21 is a knife obtained on the steep ascent to the upper echelons of production knife collecting. It’s not a starter knife. It is something to be gradually aspired to, pined over, and then climatically acquired.

I had such an experience when I bought and reviewed a small Sebenza 21 back in 2011. Although no stranger to nice knives at the time, it was one of my first forays into the $300+ knife category. And much like an exhausted mountaineer in awe of the view having reached the summit, I was suitably impressed with the CRK Small Sebenza.

Buy the CRK Sebenza at BladeHQ

In that space between 2011 and now I like to think I have matured in both my appreciation for knives as well as my approach to reviewing products. I also now have the budget to buy and hold more expensive offerings, like this Large Sebenza, and compare them with other expensive folding knives. I’ll spare you the essay on my “philosophy” towards reviewing knives, but the cliff notes are that I have no allegiance to any one brand. I run this website for fun, fund it independently (thanks in part to generous readers who purchase products through the links on this site – thank you for supporting my efforts and for supporting independent journalism), and have no problem telling it like it is. That also means I have no economic interest in selling you on a particular knife. My goal ultimate goal to assist you in finding the right knife.

The point of this is that my goal is to provide you with a review of the Sebenza 21 that benefits from my experience and lacks hype, gamesmanship, or “post purchase rationalization”. Sure, as an individual I will always have my own tastes and bias, but I try to point that out when I can to allow you to reach your own conclusion. That said, this is a damn fine knife, so lets get on with the review…

General Dimensions and Blade Details

The Large Sebenza has an overall length of 8.335″, has a 3.625″ blade, and weighs 4.7 ounces. As the name might suggest, this is a large folding knife and compares well in size to classics like the Strider SnG, Benchmade Griptilian, and Spyderco Paramilitary 2. I have to say that it irks me to no end when people refer to this as a “tactical knife”. It’s not. While I don’t doubt it could stab someone as well as anything else, in my mind it’s a large utility or EDC knife, and wasn’t designed with high speed/low drag operators in mind.

As an aside, it’s worth mentioning that my particular Large Sebenza is not your normal Large Sebenza. This one is from 2008 and is a special version of the knife with dual thumb studs (or thumb “lugs” as CRK calls them). It features S30V blade steel and lacks the “IDAHO MADE” moniker that, in my opinion, takes away from the appearance of the newer CRKs. So it’s a little different from what you would buy new today, but shares enough similarities for me to call this a review of the Large Sebenza 21 without hesitation.

The blade shape is a classic drop point, with CRK’s signature high hollow grind. The tip is extremely fine and the knife is ground thinly. One of my favorite details is the rounded spine. Overall, it’s a great shape for EDC, combining classic lines with precision manufacturing. The entire blade has been given a very fine tumbled finish, which looks nice and hides wear well.

Steel on my particular model is S30V, but these days the knife comes in S35VN. Both are fine steels. CRK seems to heat treat them on the softer side which is a decision by Chris Reeve that is not without its fair share of controversy. Personally, I like a relatively soft steel as it’s easier to sharpen. I’ve occasionally had a hard time putting great edges on S30V in the past, so if this blade Rockwells out to 58 RC rather than 60 then so be it. I will say that from the factory the knife comes laser sharp. It’s a high performance blade and it cuts very well. Compared to my SnG there really is no comparison, I would liken it more to the SJ-75, which has proven itself to be an excellent cutter. It slices beautifully and the edge polishes up easily on my strop.

Handle, Ergonomics, and Pocket Clip

For many, the luxurious full titanium handle is what the Sebenza is all about. The two slabs of titanium are simply adorned with a bead blasted finish, and, in this case, accented with silver hardware. The more standard version of the knife comes with blue anodizing on the thumb stud, and you can of course get the knife any number of unique graphic designs on the handle or exotic inlays. Personally, I really like my sterile silver and blasted knife.

Handle construction is simple but very well done. Chris Reeve made its name on tight tolerances, and my knife is no exception. Here you have flow through construction with a single stand off, and an interesting floating lanyard assembly. I’m not a big lanyard guy, but on this knife I decided to leave it on. There is something very traditional about the lanyard, and the unique floating lanyard pin makes it less obnoxious.

In hand you have a relatively comfortable handle. This knife doesn’t have anything in the way of 3-D machining, but all the edges have been contoured to break the handle up in your hand. The Large Sebenza is plenty big to accommodate all kinds of hands, and the jimping is near perfect in my book; there is enough texture to provide some traction without rendering the thumb ramp into a throbbing hot spot under harder use.

The pocket clip is another one of my favorite details of the knife. The “double dip clip” locks the knife in place like nothing else I own, and provides for discrete no-nonsense carry. Hands down this is a great pocket clip. The knife itself carries well for a large boxy knife. It’s reasonably slim, and the matte titanium tucks neatly into the pocket of my jeans.

Lockup and Deployment

When people talk about smoothness of a knife’s action “Sebenza Smooth” is about as high an accolade as you can offer in the production knife realm. At least, that’s how it was back in 2011. These days CRK has a little more competition with knives appearing on bearings and all, but it’s still a pretty smooth knife. Some guys like to disassemble their Sebenza and lap the washers with 2000+ grit wet sand paper to thin them down and further reduce the friction; kind of like how billionaires turbo charge their Ferraris. You have to be careful, because if you take off too much material you risk throwing off the tolerances entirely, but if you are one of those guys that can’t leave well enough alone then the option certainly exists. Most Sebenzas come with a single thumb lug, which, as a lefty, I really don’t like. I understand that they make a dedicated lefty model, but I would rather see double thumb lugs more common.

There is something eminently enjoyable about opening the blade on my Large Sebenza and feeling the lock fall into place with its soft and satisfying click. It’s almost like shutting the door on a German car. There is a level of security and refinement that I haven’t experienced with my other knives. This may be due in part to the relatively late lockup. Mine is around 90%. There is nothing to be concerned about with the late lockup, although I am sure some folks will find that aspect of the knife disappointing.

Something else to note is that there is absolutely no lock stick and no “break in” or tricks with magic markers are required. The Sebenza is designed to be simple, smooth, and dead nuts reliable. It can be taken completely apart with a single tool.

Large Sebenza 21 Review – Final Thoughts

The Sebenza 21 is a great knife and a worthy target for those ascending the ladder of production folders. BladeHQ did an excellent series of videos on the Chris Reeve factory. If you haven’t already seen them, they should give you further appreciation for these deceptively simple knives. Chris and his team have spent decades refining the tool and the processes behind it, and the end result is a high performance knife built to exacting tolerances.

With all of that said, there is an increasing amount of expensive knives competing for our dollar. High end production knives from larger companies like Zero Tolerance and Spyderco are continuing to gain ground, while an explosion of mid tech and custom offerings from boutique manufacturers dip down into Sebenza range. Chris Reeve spent decades building his reputation the hard way, attending knife shows and working with traditional media, but the age of Youtube, USN and Instagram is upon us. This new media is bringing consumers closer to the bespoke brands, and allowing young upstarts to accelerate on higher demand and wider margins. Whereas even in 2011 a titanium framelock alone would be enough to push the bleeding edge, today flippers, bearing systems, exotic steel, and 3-D machining are what grab at the attention of the increasingly savvy consumer.

Still CRK continues to do very well, and I don’t doubt that success will continue for a long time. The Large Sebenza is a great example of this, as it is both great knife and modern a classic. I think it’s worth having in any higher end collection. It’s the knife for guys that want a no-frills, highly functional tool. CRK gets so much right, it’s hard to find fault with the Large Sebenza. But in the midst of a golden era of mid tech knives, I can’t help but wonder whether the Sebenza will continue to be regarded as the peak of the mountain, or serve more as a stepping stone into the great white north…

Large Sebenza 21 – From $410.00
From: BladeHQ

I recommend purchasing the Large Sebenza at BladeHQ or KnifeArt. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Strider SJ-75 Review

by Dan Jackson 5 Comments

I have come to really enjoy my Strider SnG. Perhaps its because I won it in a contest, and therefore, had no qualms about carrying and beating the crap out of it. Regardless, it is a knife I have really enjoyed. But honestly, if my money was on the table, I’m really not sure the SNG would have been the first Strider in my collection. I have enjoyed the classic Strider look, but something really spoke to me about the refined lines and deep hollow grind of the SJ-75, and I always thought it would be my first Strider. Oddly, it’s my third, purchased after experiencing both the SnG and the PT. But under different circumstances it probably wouldn’t have been that way, and I think in the eyes of many collectors I’m not alone.

Strider really created something different with the SJ-75, and it merits further consideration…

General Dimensions and Blade Details

The SJ-75 has an overall length of 7.125″, sports a 3″ blade, and weighs 3.8 ounces. Strider describes this as the bridge in their lineup between the SnG and PT, but I’d say it’s more akin to the SnG than anything. The knife is definitely more compact than the SnG, but the cutting edge is pretty much the same length. It can make for a nice EDC and compares favorably in length to my Sage 1, which as you may be aware is my self-described “perfect EDC.”

The leaf shaped blade of the SJ-75 features a very prominent slanting hollow grind. It’s a neat look and an interesting departure from the flat chunky grinds found on both my PT and SnG. Apparently, some of the very first SJ-75’s were hand ground by Mick Strider himself. I bought my knife used, so I have no idea if it has been hand ground (or even what steel the blade is), but I am a big fan of the deep lean grind and the lustrous satin/tumbled finish that the entire blade has been given. I will say that I am not as crazy about the decorative file work that has been applied to the spine of the knife. I think the filework looks busy, and is something I would have left out if it were my design.

Steel choices seem to range on this model from 154CM to S35VN. There may be other offerings in the mix, special editions and whatnot, but tried and true 154CM and S35VN make up the majority. This is a good thing, as I like both blade steels, and Strider’s heat treats have proven themselves capable many times over. Again, I don’t really know what blade steel my particular knife has, but it’s stainless, holds a nice edge, and sharpens easily enough. Beyond that I really don’t care.

I ran my SJ-75 through the usual battery of tests and it performed really well. My SnG and PT, while fun knives to carry and admire, aren’t particularly keen slicers. The SJ-75 on the other hand positively zips through materials. I crunched cord, carved cardboard, and worked my way through several pieces of wood. The deep hollow grind is a significant improvement over the blocky flat grinds of my other Strider knives. And at the end of the day I was able to restore my edge with a few licks on a loaded strop. This, my friends, is how a $400 knife should cut.

Handle, Ergonomics, and Pocket Clip

The handle of the SJ-75 is an angular affair of G10 and titanium. Compared to my SnG, it looks like they took the fit and finish up a notch. It shares the same hardware, but the the edges have all been nicely chamfered, the lock bar is precision cut, and the handle pieces are suspended between a pivot and a single spacer; the ultimate flow through design. Again you find the filework on the back of the handle slabs, which is something I could live without. Aside from that I’ve got no complaints with the handle.

The G10 and titanium are both smooth. There is fine lined texture on the TI while the layers on the G10 show side exhibit depth like a piece of wood. The result is a handle that is visually interesting without being uncomfortable and obnoxious. The handle slabs have been “CC’d” to melt in the palm, and the absence of atrocious jimping, is noted and appreciated. This is a stout knife, but there is plenty of room even in larger hands for 4 fingers, and the humpback handle rests comfortable in the crook of your palm.

The pocket clip is classic Strider, and has been lifted off their other models. It’s right side tip up carry only, and the combination of a single screw and and slotted handle keeps it firmly in place. This isn’t the ultimate deep carry pocketknife, but they mounted the clip about as deep as they could. There is just enough poking out to easily grab the knife, yet it remains reasonably discrete and very secure.

Deployment and Lockup

For deployment you have Strider’s ubiquitous oval thumb hole, and it’s positioned high on the handle for easy access. The knife isn’t as smooth and easy to open as my SnG, maybe due to the tighter tolerances or lighter blade, but the knife still opens purposefully with the brush of a thumb. Strider went for large phosphor washers giving the knife smooth and purposeful action. They are only going to get smoother as the knife continues to break in.

The 3-D machined titanium is deceptively thick, and makes for a substantial frame and lockbar. My knife locks up around 40% and it is extremely tight. There is not even a hint of play in any direction and no stick whatsoever. Strider has had plenty of chances to refine their titanium framelocks, and the result here is highly refined.

Strider SJ-75 Review – Final Thoughts

The SJ-75 may very well be the Strider for guys who don’t like Striders. Compared to the overbuilt SnG and SMF, the SJ is practically a gentleman’s folder. What is impressive to me is the high level of fit and finish. Strider, much like Emerson, has earned a reputation of creating knives that are slightly imperfect users, but this is a knife that is extremely well made and meticulously finished. The reasonable size and weight and a practical grind means this is arguably their best EDC offering yet.

If I could change anything I’d do something about the file work on the inside of the handles and on the spine of the blade. Sometimes less is more, and I think now would be one of those times. Aside from that it’s a great knife, provided, of course, you can overcome the $400.00 price tag. Whether you want an upscale EDC or something for the collection, the SJ-75 is worthy of your attention.

Strider SJ-75 – From $400.00
From: BladeHQ

I recommend purchasing the Strider SJ-75 at BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.