Made in the USA

Hinderer Knives XM-18 Slippy Review

Hinderer Knives is a company best known for their overbuilt XM Series. Burly titanium framelock flippers that helped popularize the titanium framelock flipper. So to see them release the XM-18 Slippy, a slip joint using their XM pattern, is a bit of an oddity. But then again, it’s not that surprising given the recent resurgence of interest in slip joint knives.

Buy the Hinderer XM-18 Slippy at BladeHQ

And oddly enough this may be their most practical daily carry folder yet. Reasonably small, slim, lightweight, and retailing for under $300, this may be the Hinderer that you didn’t realize you needed.

General Dimensions and Blade Details

The XM Slippy has an overall length of 7″, a 3″ blade, weighs 3.71 ounces, and is made in the USA. It’s a great size for urban or suburban daily carry. It has similar dimension to the XM-18 3″, but is a hair thinner, .4 ounces heavier, and $150 cheaper.

I think if they had to borrow from one of the XM framelocks, the 3″ version was smart. This is all I need for an EDC knife. The 3.5″ version would have been way too much.

Hinderer has rolled this knife out in a couple of blade shapes, but shown here we have their classic drop point. It’s hard to go wrong with the clean look and practical features of a drop point. A good functional tip, plenty of belly, and Hinderer’s high flat “slicer” grind all work together to provide all-round performance.

Most of these early XM-18 Slippys appear to be coming with CPM-20CV blade steel. We are starting to see more high end knives in CPM-20CV. I’ve reviewed a couple Benchmade knives in this steel, including the G-10 Griptilian. Another notable knife in CPM-20CV is the Cold Steel 4MAX.

So at this point I have a few knives in my long term collection in CPM-20CV and I’ve put some miles on them. CPM-20CV is Crucible’s answer to Boeller M390. It’s the same chemical composition as M390, but it’s made by Crucible in the USA. I think it’s a great steel, and it provides a good blend of edge retention, ease of sharpness, corrosion resistance and toughness. Here is a link to ZKnives’ page on 20CV where you can get some more details.

In practice this is a slicey knife that has performed admirably in all the typical EDC chores. I have used my Slippy for your basic EDC knife stuff including opening mail, breaking down boxes, light food prep, and the random jobs that you invariably encounter when carrying a pocket knife. For each task the Slippy worked fine. It slices well and the stonewashed finish hasn’t shown much in the way of wear. Edge retention has been great, and when it’s time to touch it up, all I’ve needed to do is run the edge along the fine stones that came with my Spyderco Sharpmaker. I can’t ask for much more out of a daily carry blade.

Handle, Ergonomics and Pocekt Clip

The handle is textured G10 scales over titanium liners secured with Hinderer’s custom hardware. One complaint is they have a lot of extra bolts on this thing. The show side has the pivot, 2 bolts by the lanyard hole, and then 3 button head bolts running across the handle. These may be necessary for their slip joint mechanism, but it’s not pretty. It would look much cleaner if they could ditch the button heads.

Beyond that, everything has been executed with Hinderer’s typical care and attention to detail. All the pieces have been beautifully finished, the parts line up, and any sharp edges have been broken. Anyone who has handled a regular XM will know what I’m talking about. The fit and finish is top notch.

This is a comfy little knife. The 3″ XM pattern is tried and true, and it’s just the same for this slip joint version. You have a good size handle with plenty of room for a full 4 finger grip. If you want to choke up on the blade you can with the forward choil. There is a run of mild jimping on the spine of the handle right above the pivot, and the textured G-10 scales offer grip without shredding your pocket like a fresh emery board.

The pocket clip is your standard XM-18 spoon style clip positionable for right side tip up or tip down carry. This is a proven clip that does a good job of keeping the knife mostly buried in the pocket. Hinderer includes a filler plate so you fill the void in the G-10 when you reposition the clip.

There isn’t much to complain about when it comes to this pocket clip. Some may favor a deep carry clip, but very little of the handle peeks up out of your pocket anyway. In practice the Slippy carried like a dream. Thin, lightweight, and discreet.

Walk and Talk

For the most part, all the stuff above is essentially a review of the 3″ XM-18 in CPM-20CV steel. Nothing earth shattering in my findings. This section is where it gets interesting. Our titanium framelock has been replaced with a slip joint, and our flipper and thumb studs have been replaced with an adjustable thumb disk.

The thumb disk is removable with an allen wrench, so this knife can be made into a 2 hand opener. Good for certain legal jurisdictions. Personally, I left the thumb disk on, but I did adjust it by loosening it with an allen bit from my WiHa bit set, and then sliding the thumb disk down the channel cut into the blade.

I positioned it to a good “sweet spot” where my thumb naturally brushes it when gripping the knife. In practice I think this is a cool feature. The groove in the blade may look a little weird at first, but I quickly got over it, and I like how the thumb disk can be adjusted to fit your hand.

Here is a size comparison with the Slippy next to my Spyderco Native 5:

Lets talk about the walk and talk, since this is a slip joint after all. The backspring on this knife is pretty good. I’d give it a “6” on a 1-10 scale, with 1 being floppy, and a 10 requiring significant force. I’d put most Swiss Army Knives around a 3 or 4. The Slippy has a good amount of resistance, but it won’t rip your fingernails off as you try to open the blade.

The blade opens up with a satisfying snap, and that same strong spring holds the blade open. There isn’t a hard half stop, but there is a “no man’s land” at the 90 degree point. From there you can push the blade closed and the spring takes up the slack to bring the blade home.

Blade centering is perfect on my knife.

Hinderer Knives XM-18 Slippy Review – Final Thoughts

I liked this XM-18 Slippy more than I expected to. What I appreciate is the simplicity. The Slippy has everything you need, and nothing you don’t. I know everyone’s needs are different, but for me 99% of the time I don’t need a locking folder for my daily carry chores. So this slip joint version strikes me as streamlined and practical given what I require out of an EDC knife. For those wanting a more robust locking folder, there is always their regular XM-18 series.

In addition to the practicality of the XM-18 Slippy, I’m also drawn to the price. A sub $300 Hinderer is an accomplishment in my book. The Slippy is a full $150 cheaper than their framelock version. It’s still expensive, but this is a relatively small batch precision product made in the USA. It oozes the kind of quality you would expect from Hinderer. My example is flawless, and at this price I’m a little more inclined to roll the Slippy in my daily rotation carry than keep it as a collectible.

As for potential downsides, I’m not a fan of the extra screws featured on the show side. I haven’t taken this knife apart to see why the bolts are necessary, but probably should. If I do I’ll snap a picture and update the review. Also, some may not be able to get around the thumb disk and channel in the blade. It’s unusual and strikes me as an acquired taste, but I don’t mind it. Like the rest of the knife, it’s practical and it works.

In closing I think Hinderer did a nice job with their take on the slip joint. The slip joint bandwagon has been gaining a lot of steam lately, but Rick and his team have found away to offer a unique take on the slip joint that compliments their existing lineup. Recommended if you are looking for a premium non-locking EDC, are curious about the design, or are a fan of Hinderer knives in general.

Hinderer Knives XM-18 Slippy
From: BladeHQ

No products found.

I recommend purchasing the Hinderer Knives XM-18 Slippy at BladeHQ, Amazon, or Knife Art. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Demko Knives AD-15 MG Review

by Aaron Shapiro 5 Comments

There are knives that elicit feelings of elegance and delicate class, and then there are knives that make you feel like you’re carrying a tool that can handle damn near any task that you throw at it. Demko Knives belong solidly in the latter camp.

Buy the Demko Knives AD-15 at BladeHQ

No products found.

For those of you that are hearing the name Demko and it’s sounding familiar Andrew Demko is the designer of Cold Steel’s famed Tri-ad Lock as well as some of their (in my opinion) coolest designs. Demko has also maintained his own custom knife shop, producing well built heavy-use folders that kept that distinct look that made his name famous among knife aficionados.

Based on my experience knives from Demko’s shop directly were a little difficult to come by when I first started getting into custom pieces. I’m not sure if that due to his work with Cold Steel, or maybe just the circles I ran in… but recently Andrew did two things that changed this. First he developed a new lock, the scorpion lock, that is not available from Cold Steel and secondly, he developed his Machine Ground (MG) series.

I would probably call his MG series mid-techs, although from what I have heard the only difference between Demko customs and the MG’s is the actual grinding of the blades themselves. Obviously his customs are hand ground, while the MGs are machine ground. More on that later.

First, the ever important specs of our Demko Knives AD-15 MG, the subject of this review:

Blade Length: 3.75”
Overall Length: 8.625”
Handle Thickness: .59”
Blade Thickness: .196”
Steel: S35VN
Weight: 6.4oz
Lock: Demko Scorpion Lock
Country of Origin: USA

(Please note these measurements are according to my ruler and calipers. The manufacturer’s listed measurements may vary.)

Blade Details

So, as I stated in the intro these knives are part of the “MG” series that the Demko shop is now putting out. I think the overall idea is to get some of their knives into customer’s hands without having to have the custom price-tag attached. In order to cut down on the cost, they have opted to put Machine Ground blades in these AD-15s. Apart from that I think there are minimal cosmetic differences between these and the customs.

So what does this mean for the end user? Well, nothing really. The knife is evenly ground, with crisp lines and a thin flat grind, and it is finished extremely well. For the run that was available at Blade Show, where I bought this knife, they had actually gone back and put a machine-satin or grind-line finish on the blade. This is generally my preference in a blade finish.

All that said, the knife came to me horrifyingly sharp, and I say this as someone that can sharpen a knife to a mirror–hair whittling edge. The Demkos did something to make this knife glide through paper like nothing I’ve seen. What makes this even more remarkable is the blade is made from 4.5mm thick stock. That is thick stock for a folding knife.

The steel choice is worth noting as well. S35VN is a weird pick for a knife that I’d consider a “heavy-use knife.” Don’t get me wrong as S35VN is generally a fine steel. I have it in my Chris Reeve knives and it’s performed great for me, but I would have expected 3V or M4 in this monster. Gimme something with some real brawn, Demko!

I suppose the choice of S35VN isn’t really a problem, as S35VN is still a premium steel with a well deserved reputation for all-round performance. It was just a surprising choice to me as this knife is otherwise entirely overbuilt. I think a tougher steel with a greater reputation for hard use would have been even better under these circumstances.

Handle, Ergonomics, and Pocket Clip

To address the elephant in the room before we talk about anything else, the AD-15 MG is a big knife. I mean the thing is over eight and a half inches long. However, as a result Demko was able to figure out how to incorporate a very effective saber-style handle to the knife. This allows you to grab onto it and know that you’re not going to slip anywhere, and to add additional traction most of these knives are offered in textured G-10 or Micarta for even more grip.

As for the handle material itself, it’s okay. Don’t tell anyone I said this, but I kinda wish I had gotten a G-10 version. The natural micarta has a raw edge that has turned out to not really be my favorite. His G10 knives were very nicely squared away, I’d love to see one in CF.

The Demko’s are also now offering these knives in full Ti handles. This was debuted at Blade 2018. In my opinion full titanium is a lousy “upgrade” as it adds nearly $200 to the price tag and a lot of extra weight, but the full titanium version offers no additional operational strength.

The clip is a ho-hum spoon style three screw clip that straddles the lanyard hole. This placement makes the knife ride a bit high in the pocket. I love and hate this high clip placement. On one hand, it allows you to have a really positive grip on this (expensive) knife in your pocket when you withdraw it, but the knife is also is going to dig into your side when you sit down. So this clip configuration has its pros and cons.

Deployment and Lockup

Dudes, this lock is super weird. Like, I get it, and I like it, but it took me a solid 2-3 days of playing with it where I stopped nearly cutting myself when I tried opening it. The knife is not that different from the famed Tri-ad lock that Demko licensed to Cold Steel. It’s essentially a titanium bar that runs across the top of the knife, that bar pivots around a pin towards the rear, when doing so it lifts the locking pin and allows you to close the knife. That same spring tension also serves as the “detent.” As a result, you sorta have to push away from the pivot when you open the knife otherwise it won’t budge.

As I said, it’s a different but ultimately intuitive way of opening a knife. Another result of this lock is that the action of the knife has a very hydraulic feel to it. It’s smooth, but slow. As if you were pushing the blade open through soft butter. This isn’t a knife that you’re gonna “pop” open with your thumb. The AD-15 MG’s run on poly washers, so that contributes to the slow hydraulic feel of the action.

Demko Knives AD-15 MG Review – Final Thoughts

How do you pin a bow on a knife this unusual? It’s a new style of mid-tech, with a new locking system, in a different size category than I normally buy. I never condone knife abuse, but the AD-15 seriously feels like a knife that could do pretty much anything and go pretty much anywhere. Need to stab through a car hood? No problem. This AD-15 MG is an absolute tank, and in that capacity this knife is phenomenal.

With a different steel I think the AD-15 MG’s would be perfect. S35VN is fine for a Sebenza, but for an overbuilt folder like this I’d love to see the jump to an even tougher steel like 3V. I believe that Demko has used different steels on the hand ground versions, so perhaps that will trickle down to the MGs eventually.

Also, these knives aren’t cheap. The base model (with G10 or Micarta) comes in around $675 and is readily available on BladeHQ or even Amazon. This AD-15 MG is a lot of money, but you’re essentially getting a custom Demko that has a blade that went through a double disk grinder. Practically speaking it’s very similar to what they’d call a “custom knife.” The hand ground version of this knife starts at $900, and if that’s if you can find one.

For these reasons, I recommend the Demko Knives AD-15 MG if you want a hard use folder from Andrew Demko without spending the cash on one of his full customs.

No products found.

Editor: I recommend purchasing the Demko Knives AD-15 MG at Amazon or BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade Anthem 781 Review

by Aaron Shapiro 3 Comments

Last Updated: July 18, 2019

There was a time when Benchmade was kinda the sleepy “Gunshop Knife Brand.” There would always be a few dusty Griptillians sitting in the case next to the preowned Glocks, and while the Grips might be fantastic value-props, they a bit vanilla-icecream-y if you get my meaning.

Buy the Benchmade Anthem at BladeHQ

Buy on Amazon

However, something has been changing in the last few years. I don’t know if someone put some sriracha on the break table over there in Oregon City, or what, but something has injected some pep into their design team. Introducing the Anthem 781, Benchmade’s first Integral Titanium folding knife. There are lots to say about this one, but before I get too deep let’s go over some specs:

(Please note these measurements are according to my ruler and calipers, manufacturer’s listed measurements may vary.)

Blade Length: 3.25” of cutting edge, 3.375
Overall Length: 8.125”
Thickness: .585” with clip, .421 handle only
Blade Thickness: .115”
Steel: 20CV
Weight: 3.7oz
Lock: The famed Axis Lock
Country of Origin: USA

Blade Details

With a knife like the Anthem, I believe that it’s intended to be a daily carry type piece. It’s not overly large, doesn’t have any sort of complicated aspect to it, and the functional bits are designed to be, well, functional.

The blade is a great example of this: drop pointed shaped with a rounded (or crowned) spine. Eyeballing it, I’d guess that it’s flat ground but I suppose it could be a shallow hollow grind as well; either way, it’s a great slicer. It came out of the box with a very nice, toothy, utility edge and I didn’t feel the need to change this on my wicked edge. In the couple of weeks that I’ve been carrying it I have had occasion to break down boxes, slice up food, and perform just daily “knife-stuff” tasks with it, nothing crazy, no batoning or zombie apocalypse type stuff, but in terms of daily EDC tasks, it excelled.

In terms of the steel, I will briefly comment on it: Benchmade chose 20CV for this blade, and I believe that to be an excellent choice for a knife like this. 20CV is a high toughness and corrosion resistance steel, that hardens to around 62HRC. I have no means testing to see if my knife is in that range, but I can tell you that it’s performed beautifully and has been easily maintained on a strop. 20CV is very similar to M390 (one of my favorite steels) and I have been really pleased with it in this application.

Handle, Ergonomics, and Pocket Clip

Ah yes… The INTEGRAL handle. This is really what makes this knife stand out, isn’t it? This is the first Integral from Benchmade. For those of you not familiar with the term: Integral means that the handle of this knife is milled out of a single block of Titanium as opposed to two that are screwed together. There aren’t any screws holding the knife handle together. In the past, this level of knife making was reserved to custom makers that had a lot of time on their hands (it takes a while to mill a channel out of a block of Ti) but recently a few companies have started incorporating integrals into their lineup.

One of the interesting things about Benchmade’s execution of the integral handle is how they incorporated the axis lock into it. When you look at the spine of the knife (the money shot of any integral) you’ll see two screws hidden in the decorative milling, these hold the locking method in place.

In the hand the first thing that came to mind for me was how thin the knife is; It carries very well in the pocket and feels great in hand. The handle itself is trim in both dimensions thickness and height, but there is a sort of faux-choil towards the blade that locks the hand in securely when holding the knife open. Otherwise, the milled texture gives you a little bit of grip on what would otherwise be a pretty slick knife.

The pocket clip is an ambidextrous milled Ti clip that is more than a little phallic, but it is also very functional. There are several makers out there that are offering custom clips made from Moku-Ti so if you want something different there are options for you. The knife carries well with approx 1/2” sticking out of the pocket, offering a perfect grip to withdraw it.

Deployment and Lockup

The blade on the Anthem opens by way of ambidextrous thumb studs. The blade deploys easily thanks in part to bearings washers. The action is smooth and easy.

For lockup, the Anthem comes equipped with Benchmade’s Axis lock. I’m not sure there’s much to say about the Axis lock that hasn’t already been said. It’s an incredibly solid lock mechanism that isn’t prone to lock rock, doesn’t really suffer from failures in the way a liner or frame lock might, and it is completely ambidextrous to use. The execution of the Axis lock is worth noting on the Anthem, there’s a block screwed to the spine of the knife that acts as the anchor point for the axis lock mechanism.

Benchmade Anthem Review – Final Thoughts

So to wrap all this up…the Benchmade 781 Anthem is a great step forward for Benchmade knives. I think it shows a focus shift on Benchmade’s part too, hopefully, starting to produce some higher-end knives. I am also very pleased to see their adoption of some different steels. I love CPM154 and S30V, but it’s good to have some variety. Between the 20CV here and the S90 in the 940-1, it’s been refreshing.

Now, the caveat to this entire review: This is an expensive knife. MSRP is around $500, with retail landing closer to $425 on BladeHQ and Amazon. Competitively, this puts you in the ballpark of a Chris Reeve, or above the ballpark of some really nice Zero Tolerances, but what you’re paying for here is the time and difficulty in making the handle. It’s a remarkable feat, but you have to decide if it’s worth it to you, for me it was too cool to pass up. The nice thing, however, is that you won’t be getting a gimmicky integral for that price—you’re going to be putting a knife that will make a great daily carry in your pocket.

Sale

COLD STEEL AD-10 3.5" S35VN Steel Ultra-Sharp Drop Point Blade 5.25" G-10 Handle Tactical Folding Knife with Tri-Ad Locking Mechanism

CONSTRUCTION - The AD-10 tactical folding knife features an ultra-wide, ground thin at the edge, honed to razor-sharpness blade that offers unprecedented cutting, shearing, and piercing power while resisting bending, breaking, or chipping
S35VN STEEL BLADE - Crafted from S35VN steel, the AD-10 folding knife's blade ensures super-fine cutting edges and exceptional edge retention; This premium steel is renowned for its durability and ability to maintain sharpness through rigorous use
STRONG HANDLE - The handle of the AD-10 knife boasts heat-treated, full-length aluminum liners and 3D machined G-10 scales, providing unparalleled strength and grip; Its precise contouring and integral finger guard ensure a snug and secure fit in the hand
TRI-AD LOCK - Complete with the Tri-Ad, the AD-10 offers unrivaled strength, shock resistance, and durability; This reliable locking mechanism provides peace of mind, safeguarding your fingers during use and ensuring the blade remains securely in place
SPECS - Weight: 7 oz (198.4 g); Blade Thickness: 3.8 mm; Blade Length: 3 1/2"; Blade Steel: S35VN; Handle Length/Material: 5 1/4" G-10; Overall Length: 8 3/4"; Knife Type: Folder; Blade Shape: Drop Point; Locking Mechanism: Tri-Ad Lock

I recommend purchasing the Benchmade Anthem at BladeHQ or Amazon. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Great Eastern Cutlery #71 Bullnose Review

by Benjamin Schwartz 3 Comments

Traditional knives are like genre fiction: they’re expected to follow certain tropes. These conventions are more restrictive than those we impose when we say things like ‘tactical knife’ or ‘EDC knife,’ maybe because they’ve been cultivated over a longer period of time. However, as with a fantasy or horror novel, it’s possible for a traditional knife to transcend its label and achieve greatness, whether it’s working outside of its associated tropes or within them. When a traditional becomes great outside its tropes you get things like the Spyderco Roadie. When it achieves greatness within them, you get Great Eastern Cutlery.

Buy the GEC Bullnose at BHQ Buy the Bullnose at KniveShipFree

GEC makes traditional knives, not as they actually were back in the day, but as we fondly remember them to be (or are told to remember them). Operating out of historic Titusville, PA, GEC turns out batches of knives ritualistically grabbed up by collectors and enthusiasts eager to own these tangible remembrances of a perceived better time.

But GEC doesn’t just peddle nostalgia porn. They make truly great knives, with fantastic fit and finish, in a variety of materials both man-made and (sadly) natural. And among patterns both original and obscure, GEC also puts out classic styles, often with some slight tweaks to them. Such is the #71 Bullnose, which is GEC’s gentle revision of the Sodbuster pattern.

I picked up a Bullnose in 2017. GEC produces their knives in batches, and the latest run of Bullnoses has hit the market. Should you buy one?

General Dimensions and Blade Details

GEC’s Bullnose has a blade length of 3.1 inches, a handle length of 3.8 inches, and a weight of 2.4 oz. It is made in the United States.

This take on Sodbuster doesn’t exactly reinvent the wheel, but you get a few little perks not seen on most Sodbusters: a wider butt end, and a big lanyard hole. The Bullnose hovers pleasantly in that arena of decent-sized knives that still maintain high pocketability. It can tackle most any cutting chore and yet drops into a pocket without a second thought.

Superlative fit and finish is a hallmark of a GEC knife. These are lovingly crafted knives, pleasures simply to hold. I’ve had some very nice GECs including two different Tom’s Choice Barlows, and they’ve all been beautifully finished, but my Bullnose is the nicest of the lot. The layers are airtight, the corners chamfered, the blade centered. The swedges are somewhat uneven, but I haven’t seen any outfit get something like that consistently perfect. Basically it’s all good, no matter which way you turn it or where you look.

Presumably we get the name ‘Bullnose’ from the blade shape: a drop point, but with a squat front end, squashed in like the face of a pug. I suppose the idea is to add some meat to the tip without compromising piercing power, and it mostly succeeds in that. The Bullnose isn’t exactly a needle point but it punches through material easy enough. Another effect of the blade shape is to reduce the belly to a compressed section just below the tip, meaning that most of the working edge is a straight line. Not a bad thing, and when I needed the extra cutting muscle of a belly I angled the knife so that portion was pushing down into the material and went to town.

1095 steel is one of the traditional knife tropes. It’s a carbon steel, so you have rust to worry about – but you know that going in so I’m not going to fault it for that. Once you get a patina forming, the blade turns a smoky, cloudy gray and receives a noticeable boost in corrosion resistance. It holds an edge well if you’re cutting softish things like thread or food, but on rougher media like cardboard, edge retention isn’t going to be phenomenal.

Simply put, 1095 is mediocre. Not bad, but not great – not even merely good. GEC used to implement 440C on some of their blades and I would like to see that on the Bullnose, at least as an option for those who want it. If the Bullnose is sincerely meant as a working knife, I think the rust resistance and boosted edge retention would be worthwhile.

On a side note: I think I’m alone in this, but this is my fourth GEC and I’ve always found their 1095 exceptionally difficult to sharpen. Like, harder to get sharp than VG-10. From what I understand they run the steel a little harder than normal, and maybe this, combined with the thin edge geometry on these traditional blades, stymies my sharpening skills. But it’s definitely another black mark against the steel choice.

A Brief Digression into Warranty Stuff

You may be able to tell from my pictures, but there’s a nick in the blade of my Bullnose. Turns out that the blade was smacking against a portion of the backspring in the channel, where it rises to accommodate the pin that keeps it in place. Basically, it folded over a bit of the cutting edge.

Once I figured this out, I sent the Bullnose to GEC, and they called me when they received it with a diagnosis. They said they could fix it, but because they don’t have a dedicated warranty department the turnaround wasn’t going to be lightning quick. A few weeks later, I got it back, and it seems like they fixed it, seemingly by sharpening the blade itself down a bit – not an elegant solution. The fold wasn’t completely sharpened out, just enough to stop it from happening anymore.

All of this isn’t to hate on GEC’s warranty work. Given the nature of how they operate, the full fat warranty departments of the big production companies isn’t feasible. But just be warned that if you have an issue, the resolution of that issue is going to be a little more homespun than what you’d get with LifeSharp, for example.

Handle, Ergonomics, and Carry

The Bullnose’s handle starts with a sizable butt end that tapers into a narrow, square neck. The finger side of the handle describes a gentle arc from tail to tip, with a flattened region just below the pivot where your index finger goes in a natural grip.

That’s a lot of words to describe what, in practice, is about as simple a handle as you can get – and the simplicity works. I was worried the beak would bite into my largish hands, but there’s enough room so that it keeps my hand in place without digging into it.

GEC releases its models in a gaggle of different handle materials, so the ‘grippiness’ of your particular choice may vary from my own. I chose the natural canvas Micarta which, despite its burlapy appearance, is pretty smooth – there’s just a hint of traction, more than enough for my uses, but you can probably find grippier options in the lineup. Something that may not be clear in pictures is that the Bullnose is a thick knife: the handle is half an inch wide. Wideness doesn’t always equate to comfort, but in this case it does. All work knives should be comfortable and the Bullnose handily makes the grade.

I lavished many words on the Bullnose’s simple handle, so I’ll be more concise in describing how it carries: perfectly well. Drop it in your pocket of choice and forget about it.

Deployment and Lockup

We’re back into trope land here – nail mark, two-hand deployment; you know the drill. I don’t really get nail marks. And I don’t mean that I find them outdated. For me, they just don’t work well. Is there any knife where sliding your stubby, frangible nail into a shallow divot is easier than just pinching the blade and pulling?

Well, I guess you can deploy the Bullnose either way without undue fuss. Pull is a stiffish 7, about perfect for a knife of this size and intent. I also appreciate the half stop. We’ve all had regular folding knives come down on our fingers when we close them negligently – but imagine the blade coming down with the force of a backspring behind it. Half stops are a safety feature that makes sense to me.

The strong backspring keeps the Bullnose’s blade open with surety, too. We associate the term ‘hard use’ irrevocably with locking knives, but the Bullnose feels like it could do rigorous chores without any danger of failure, as long as it’s used sensibly.

GEC #71 Bullnose Review – Final Thoughts

The Bullnose is without a doubt my favorite GEC knife. I don’t truck with multibladed traditionals, and while GEC makes quite a few single blade patterns, the Bullnose in particular enjoys a harmonious alchemy between size, utility, and (most importantly) affordability.

It checks all the GEC boxes – old school materials, delectable fit and finish, refined traditional patterns – without any specialized characteristics and extras, and it comes out in a large enough quantity that you can get one without having to queue up in a raffle or face a hardy gouging on the secondary market. You may end up getting more GECs after the Bullnose, but I don’t think you’ll ever find a better one.

GEC #71 Bullnose
From: KnivesShipFree

Editor: I recommend purchasing the GEC 71 Bullnose at BHQ or KnivesShipFree. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade Proxy Review

by Dan Jackson Leave a Comment

Last Updated: September 7, 2019
Warren Osborne is one of the most recognized names in knife making. While he was an extremely talented custom maker, a large part of his renown is due to a series of high profile collaborations with Benchmade. The 940 is one of the most notable collabs, but Warren Osborne is also known for designing the Rift and Barrage, among others.

Buy the Benchmade Proxy at BladeHQ

Buy on Amazon

Warren Osborn passed away in 2016, after a long a long struggle with a cancer. The Benchmade Proxy was his final collaboration with Benchmade. I happen to think it was an interesting design. Benchmade has only recently gotten into flippers, and this Proxy is one of their takes on a titanium framelock flipper. As Warren’s last collaboration with Benchmade I knew it was something I needed to get my hands on.

General Dimensions and Blade Details

The Benchmade Proxy has an overall length of 8.85″, a 3.87″ blade, weighs 4.86 ounces, and is made in the USA. This is a substantial knife. A bit too much for me to carry on a daily basis, but I’m sure it will make a fine EDC for those that like larger knives. At under 5 ounces, it’s plenty light and pocketable for a near 4″ bladed folder.

The Proxy features a long sloping drop point blade. It kind of reminds me of the head of a shark. For whatever that is worth. It’s a strong blade cut from near 4mm thick stock. The knife has a high flat grind and has been left thin behind the edge. It’s fine for cutting boxes or fruit, and I suspect it would hold up under tougher chores as well. The tip is placed low on the knife. That shortens the belly but makes it good at stabbing things. Benchmade went with what appears to be a matte satin finish. It’s a utilitarian finish that hides wear well.

The most prominent feature on the blade is the oversized sharpening choil. That makes it easy to sharpen, but you lose some edge, and if you aren’t careful material you are wanting to cut can get caught up in the large choil.

Benchmade selected CPM-20CV for the Proxy’s blade steel. This is the same steel my G-10 Griptilian came in, and now that I’ve owned that knife for almost 2 years, I have a little experience with it. Manufactured by Crucible Industries, CPM-20CV is advertised as a steel with high corrosion resistance and wear resistance, and good toughness. Chemically it is similar to M390, which is an excellent steel. CPM-20CV has an extremely high chromium content, which results in its corrosion resistant qualities.

In practice I have found that CPM-20CV performs admirably. It exhibits a nice balance of edge retention and sharpenability, while exhibiting excellent rust and corrosion resistance. To be compared with M390 places it in excellent company, and I consider CPM-20CV to be top tier blade steel. A great choice for a high end folding knife.

Handle, Ergonomics, and Pocket Clip

The Benchmade Proxy features a titanium frame lock mated to a one piece G-10 backspacer and handle scale. Everything is held together with torx fasteners. It’s kind of an odd combination between the light brown G-10, the sandblasted titanium, the satin hardware and the mirror polished clip. The varying textures and angular design almost make the Proxy feel like a small piece of modern art. The build quality is excellent. Tolerances are tight, the parts line up, and the 3-D machining on the handles is excellent.

I also like the omission of the lanyard hole. I’m not a big lanyard guy, but you see them on pretty much every knife. It’s refreshing to get something without a lanyard hole. While that is bound to piss some people off, personally I don’t miss it.

The Proxy is a large and comfortable knife. It’s got a big simple handle, so it will conform to most hand sizes. There is little in the way of texture on the knife, but still my fingers fall naturally in place. Warren did design a forward finger choil, and that feature allows you to choke up on the blade and get close to what you are cutting. You can also choke back on this handle, providing you a couple inches of additional reach. Potentially useful if you have to do some light chopping or use the Proxy in a “tactical” application.

The pocket clip is Benchmade’s split arrow clip, buffed up to a high shine. While I generally like the split arrow clip, I’m not a huge fan of the shiny version shown here. It’s kind of loud and it doesn’t match the rest of the knife. It feels out of place, although I’m not sure what I would have put instead of this clip. I probably would have reconsidered the entire hardware selection, finishes, and color choice.

The Proxy carries well considering it’s almost a 9″ folding knife. The sturdy split arrow clip, and bead blasted titanium handle work together to provide good traction without tearing up your pocket. At .5″ thick the Proxy is not the thinnest knife, but it’s not the thickest either. Benchmade milled out some large grooves to make it a little slimmer and more pocketable. All said, I think the Proxy is not a bad knife to carry.

Deployment and Lockup

This is a bearing equipped titanium framelock flipper. I haven’t reviewed a Benchmade framelock flipper before, so this is new territory for me. In practice it flips great. I’d say it scores a solid “7” on my 0-10 scale. Maybe a little behind the action you would find on a Zero Tolerance flipper, but not by much. It’s snappy and responsive action and the bearings are smooth. So smooth you can shake the blade closed. Nice.

The titanium frame lock is reinforced with a stainless steel insert. The insert does not double as an over travel stop mechanism, a feature I’ve come to find standard on most flippers from ZT, Spyderco, and Kizer. That said, the lockup on this knife is early, and free of any sort of play. It’s rock solid.

Here is a shot of the Proxy next to my Strider SnG. I chose the SnG because the Proxy borrows the integral G-10 handle / backspacer.

Blade centering is pretty good on my knife. Not perfect. It favors the G-10 side by a mm or so, but is nowhere near rubbing.

Benchmade Proxy Review – Final Thoughts

The Proxy is a curious knife. Warren Osborne made a name for himself providing unique designs, and I think the Proxy continues that legacy. Individually, there are number of seemingly dissimilar components. Added up they all come together. Sorta. Part of me can’t help but feel that this blade was put together with leftovers from Benchmade’s parts bin, but other parts of me appreciate the simple design. The knife is nicely made and is both comfortable to use and a capable cutter. It’s a great work knife.

While it may not be to everyone’s taste, I think the Proxy is a good knife. I appreciate the Proxy and I appreciate Warren Osborne for his contributions to the knife world. I can safely recommend the Proxy for fans of Warren and fans of this design.

Benchmade - Proxy 928, Plain Drop-Point

HIGH-QUALITY: The CPM-20CV stainless steel blade features excellent edge retention, corrosion resistance, and low maintenance. The G10 and titanium handle offers durability and great performance.
WELL-DESIGNED: The 928 features a highly strong and functional Monolock mechanism with the added convenience of a flipper. It's a manual knife that can be opened and closed with one hand.
ALWAYS READY: The 928 combines high performance and a highly modernized look. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Proxy 928's drop-point, utility blade style and all-around functionality make it ideal for everyday use, outdoor activities, and even tactical applications.

I recommend purchasing the Benchmade Proxy at Amazon or BladeHQ. Thanks for reading.

Great Eastern Cutlery Tidioute 43 Oregon Trapper Review

by Aaron Shapiro 1 Comment

I’ll never forget when my family was cleaning out my late Grandfather’s house after he passed. I found an old band-aid tin that was full of a variety (in both style and age) of small multi-bladed slip joints. They were all he carried and on most of them one blade was worn down to a nub, whereas the rest were shiny and like-new. He was a true EDCer, he didn’t think about the concept of carrying things like I do, he just made sure he had what he needed. A traditional knife was always included.

Buy the GEC Oregon Trapper at KnivesShipFree or GPKnives

Slipjoints, or traditional knives, have seen a bit of a resurgence in the last couple years with the knife community at large. So much so that you see dedicated slip joint knives being made by brands like Spyderco, Benchmade, and Lionsteel.

Great Eastern Cutlery while being relatively new on the slip joint scene when compared with the likes of Queen, or Imperial, have been generating new levels of interest and collectibility with traditional knife collectors since their founding in 2009. They’ve reborn some classic brands such as Northfields and Tidioute and honor a lot of the classic production patterns that have been in pockets for decades. All that to say, today we are going to be looking at the Great Eastern Cutlery Tidioute 43 – Oregon Trapper. Now, before we get too far into this review, I want to be upfront and say that I am not a history expert on traditional knives, so please forgive some discrepancies in that regard. This review will take into consideration actually putting the knife in your pocket and carrying it in your day-to-day life. So, without further ado, some specs:

Blade Length: 3.25”
Closed Length: 4.25”
OAL: 7.5”
Steel: 1095 Carbon Steel
Weight: 3.8oz
Handle Materials: “Frontier Bone” handle scales, I think this is just a form of cow bone, but I’m not sure.

I’ve owned a handful of GEC’s knives over the last few years, even been able to get my paws on some of their much sought after Tom’s Choice (or TC by the cool kids) special factory runs. So, when I got the Oregon Trapper in hand I was struck by one thing right off the bat, this knife is large for a slip joint. I was, obviously, aware of the size when I ordered it. The specs were clearly listed on knivesshipfree.com but it wasn’t until I got the knife that I realized exactly how big it is. Now, depending on where you fall in the slip joint community that could be a good thing, or that could be a bad thing. As a tactical knife carrier in recovery, I dig the larger size. I think it’s easy to feel, “under-gunned,” for some reason when you’re carrying a small slip joint knife by itself, but this Oregon Trapper dispels that feeling.

GEC’s chosen steel is the venerable 1095 high-carbon steel. 1095 is like a bowl of vanilla ice cream when it comes to knife steels. It’s really all ya need, but there’s nothing really special here. It’s high-carbon, so it will take and hold a fine edge very well, but it will also stain and rust if you let it. To add onto that, there is also a whole “sub-culture,” that forces patinas on their blades, and I have to admit, a well-done patina (or a naturally formed one over a long period of honest use) looks really, really nice. The steel thickness on the GEC starts at 0.113” and is ground to a blistering 0.018 before the final edge. There are sharp knives, and then there are “sticky” sharp knives where when you lightly touch the edge your skin sticks to it. This knife is the latter.

Handle, Ergonomics, and Carry

As I stated earlier the handles of the GEC 43 Oregon Trapper are made from a material GEC calls it’s “Frontier Bone,” which is a vaguely frightening term that makes you think of bleached buffalo bones in a sandy Arizona desert landscape, however, the truth is less menacing. Frontier Bone is a portion of light cow bone that’s burnt or toasted, and then polished. I think it looks pretty cool and is generally cheaper and easier to find compared to something like stag or jigged bone handles.

The one catch with GEC’s (and really all traditionals) is that these type of bone handles can vary greatly in thickness. Looking straight down at my example shows that the right-hand scale is slightly concave, whereas the left is convex. So that will always be a gamble with this particular handle material, something like micarta will not have this issue. The handle shape itself is simple, straight back with a slight swell and negative angle at the tail. This allows a solid purchase in hand but doesn’t have any choils or jimps to provide texture.

It terms of carrying the GEC 43, I use a leather pocket sheath. knivesshipfree.com include their own branded buffalo leather pocket slip, that I used for a while. I have a custom pocket slip made by a friend of mine that carries a slipjoint and a Muyshondt Maus. Due to the fact that the knife is a bit larger than your normal slipjoint it may not work with all your carry methods, but it seems to work well with these. I generally suggest some sort of pocket organizer to keep the knife vertical in your pocket, there’s nothing worse than knife sitting sideways in your pocket.

Walk and Talk

Lastly, the action. Slipjoints are measured on a scale of 1-10. 1 being the blade having zero resistance on it from the spring, and 10 being it needs the screaming He-Man strength to open it. Most GEC’s are a 6-7, they have a stronger pull than I like, but are usable and manageable. The Oregon Trapper clocks in at a solid 5, nice and smooth action with a pinch-able blade. I found the walk and talk to be a little spongey, but there is still a good positive half-stop and audible snap when closing/opening. Once opened the knife is solid and doesn’t have any movement side to side. For a production, this is perfectly acceptable.

Great Eastern Cutlery Tidioute 43 Oregon Trapper Review – Final Thoughts

So, would I suggest this to someone else? Sure, if what you want is a larger slip joint that could serve as your only EDC knife. I think the decision to transition from a locking folder to a slip joint as part of your EDC is one that takes some consideration. I would personally say that non-locking folder of any sort is more of a lighter-duty knife. So if you’re in law enforcement, construction, fire fighting, etc – I think that you’d need to think long and hard about what the lack of a lock would mean on your knife.

If you’re like me and you work in an office, and primarily open mail, packages, and cut food with your EDC knife, this is an obvious choice; and a great way to introduce some variety into your EDC rotation. As always our preferred source of everything sharp is either from knivesshipfree.com or bladehq.com both of which have this particular Great Eastern Cutlery 43 Oregon Trapper in stock.

GEC #73 Oregon Trapper
From: KnivesShipFree

Editor: I recommend purchasing the GEC 43 Oregon Trapper at KniveShipFree or GPKnives. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.