Knives By Purpose

CRKT Crossbones Review

It has been a good while since I have reviewed a CRKT knife. I wanted to remedy that situation, but struggled with selecting a knife. I like a lot of their designs, but sometimes weight gets in the way. For example, I like how they paired up with Eric Ochs to create the CRKT Avant, but at 5.4 ounces I couldn’t quite pull the trigger.

Buy the CRKT Crossbones at BladeHQ

Buy on Amazon

The Crossbones caught my eye in part because it weighs less than 2.5 ounces, but also because CRKT has decided to double down on the design and release a high end version of the knife. To me, that signals the design has gotten some traction, and we may have something special on our hands.

The story behind this knife and it’s designer is also intriguing. This knife was designed by Jeff Park. Jeff has worked for Ken Onion for 10 years in Ken’s shop in Hawaii. The job quickly blossomed into a mentorship, and Jeff collaborated with Ken on the design that ultimately became the Crossbones. CRKT did a superb video overview of the knife that offers back story and a view into the design considerations.

So after careful consideration I bought the Crossbones off Amazon and a few days later it was at my door. On that note, I bought this knife with my own money. This is the same for every other knife I review unless noted otherwise.

General Dimensions and Blade Details

The Crossbones has an overall length of 8.06″, a 3.54″ blade, weighs 2.4 ounces, and is made in Taiwan. This is a lightweight big-bladed EDC not unlike the Boker Urban Trapper. Where the Crossbones differs from the Urban trapper is that the Crossbones is much thicker. On the flip side the Crossbones will hold up to harder use much better than the Urban Trapper.

Speaking of the Urban Trapper, here is a quick size comparison:

Another obvious comparison is with the CRKT Swindle. The swindle is about half an inch shorter and an ounce heavier. The Swindle is also half the price of the Crossbones. When you hold the two knives at the same time, you can see where the extra money went on the Crossbones. The machining, especially in the handle, is much more elaborate. Both knives fall into that “slim and slicey” EDC knife category, and the Crossbones in particular reminds me of a folding filet knife.

It’s worth mentioning that if you are looking for something much larger, CRKT also offers the Jumbones, which is a version of this pattern with a near 5″ blade. That is getting you even further into folding filet knife territory.

The Crossbones features a dramatic trailing point blade. Designer Jeff Park apparently took inspiration from the tanto blade shape, and he describes the blade as a “modified tanto”. Regardless what you have here is a long and thin blade. Blade stock is actually pretty robust at approximately 3.3 mm thick tapering down to a fine tip. The full flat grind gets pretty thin towards the edge and the satin finish is clean and easy to maintain.

CRKT selected AUS-8 for the blade steel. That is likely to get some grumbling, especially given the over $50 price tag. If you like the design and want to splurge, there is the premium version in M390, but it would be cool to see this in VG-10 or 154CM. I realize from a manufacturing logistics standpoint that could be expensive at best and impossible in some instances.

AUS-8 has a reputation of being a softer steel that is easy to sharpen but won’t hold an edge as a long as harder more expensive cutlery steels. On the plus side I’ve found AUS-8 to be a hearty steel that is tough, takes a nice finish, and is easy to maintain.

In practice the Crossbones performed as I would have expected. That slim blade is easy to get underneath the fold of an envelope, or into the seam of a box. The full flat grind aides in slicing, easily paring apples and breaking down boxes. The blade did slow down after some heavy cardboard cutting, but it was easy enough to bring back on my Spyderco Goldenstone. No issues with rust or corrosion.

Handle, Ergonomics, and Pocket Clip

The handle is kind of wild and crazy, and I suspect this is where CRKT allocated the majority of their budget. The 6061 aluminum handles have been heavily machined and given a dramatic 2 tone finish with bead blasted and satin finished elements. The profile of the handle resembles a dog bone, and that inspired the name. Inside you can see that the aluminum handles have been pocketed to accept stainless steel liners. Rounding things out are a partial backspacer that doubles as a lanyard hole, and custom hardware.

Fit and finish on the handle is excellent. The machining is meticulous. There is a fine diamond pattern milled into the handles. Not sure how they do that, but it probably takes some small endmills to get that level of detail. I am especially impressed by how well the steel liners fit into the aluminum handle.

The ergonomics on the Crossbones are interesting. On one hand this is a knife with a lot of sharp edges. That satin “X” shape in the handle looks cool, but the edges are sharp. Not to the point of cutting you sharp, but it’s certainly noticeable. But what I find interesting is that these sharp ridges offer a lot of traction while using the knife. Certainly this is not a piece that will easily slip out of your hand. I think for normal use the traction will be appreciated. Under more hard use conditions such as heavy rope cutting and carving wood, I think the traction is excessive and this knife is going to develop some hot spots.

I’m left a little conflicted on the elaborate design work in the handle. Some people will like this, but I would have been OK with less detail and less sharp edges. I notice that Jeff’s knife in his CRKT overview lacked the crazy millwork. Part of me wonders how that knife feels in hand compared to this production version.

In contrast to the elaborate handle, the pocket clip is a small no-frills deep carry offering. The clip is positioned for right side tip up carry only, but it’s secure, offers good spring retention, and is discreet. The knife pretty much buries itself into your pocket. Great if you are looking for your pocket knife to fly under the radar. It’s also fairly easy to retrieve from the pocket.

This Crossbones carries well. The heavily textured handle and stout pocket clip means that the knife is not going anywhere. At 2.4 ounces this is a knife you will quickly forget you are carrying until the time comes to use it. The knife is thick, but it’s not unreasonable. All said I think it behaves well in the pocket.

Deployment and Lockup

The blade of the Crossbones is accessed via a low profile flipper tab. The flipper tab is almost too low profile, thanks in part to a strong detent and rounded edges of the flipper tab. Rounded edges aren’t necessarily a bad thing. I noted in my SOG Terminus XR review that the sharp edges of the flipper tab on that knife actually cut my finger, so I’m glad that isn’t the case here.

But on the flip side, my finger has slipped off this tab without opening the blade many times. It takes both technique and concentration. So that’s a bit of a bummer, but the good news is the detent is crisp and dialed in. When the knife opens, it opens with authoritay. The blade rockets out thanks to a strong detent and IKBS bearing system.

For lockup we have a stainless steel liner lock. The lockbark engages fully with the tang of the blade, and it sits in the middle of the tang. There is no lock rock, or blade play in this knife. Out of the box the lockup was just a little sticky, but that has smoothed out with use.

Here is a size comparison with my Swindle. I still have this knife 5 years later, and it’s still an impressive budget knife. Time flies.

Blade centering is close to perfect on my knife. Maybe off by a hair.

CRKT Crossbones Review – Final Thoughts

The Crossbones is an interesting knife. I am not sure if it rises to the level of being an “iconic folding knife” but it’s certainly different, and everything and has been well implemented. Retailing around $65, it’s on the expensive side for CRKT, but they have dialed in the fit and finish on this blade and a lot of work was put into the handle. Visually the knife is striking, with it’s unique profile and monochromatic look. The heavily machined handle will read as busy to some, but I appreciate that they tried to do something different here.

Functionally the knife has a lot going for it. It’s lightweight and easy to pocket. It’s a long bold looking knife, so maybe not appropriate for all social situations, but the long thin blade can get into places other knives can’t. The handle is heavily textured and easy to grasp. I found the flipper tab a little slippery at times, but nothing egregious. Of course I’d always like to see a better steel than AUS-8, but jumping up to a better steel would probably require a corresponding jump in price. If you really like the design then perhaps snagging one of the limited edition versions is worthwhile.

At the end of the day, I can see why CRKT has offered the Crossbones in a few different configurations. It’s a cool design, and it has been well executed. While I can’t give it a blanket endorsement, I think if you are interested in the design, then the Crossbones is worth picking up.

CRKT Crossbones EDC Folding Pocket Knife: Gentleman's Knife, Everyday Carry, Satin Blade, IKBS Ball Bearing Pivot, Liner Lock, Brushed Aluminum Handle, Deep Carry Pocket Clip 7530

Smooth Opening: IKBS ball bearing pivot deploys the blade smooth
Fast Opening: The flipper deploys the blade fast
Easy To Sharpen: High carbon stainless steel blade takes an edge well
Classy Appearance: Satin finish blade has a modern look
Custom Stylings: Two-tone aluminum handle has distinctive look

I recommend purchasing the CRKT Crossbones at Amazon or BladeHQ.

Kizer Begleiter Review

by Benjamin Schwartz 1 Comment

I’m not sure any single knife company has impacted the industry more in the last ten years than Kizer. They may not have been the very first company pushing the boundaries in terms of price-to-performance, but they were the first one to get lots of attention in so doing, not only forcing their existing competitors to deliver more value for money, but also informing new companies’ entry into the knife world. Reate, WE, Ruike, Real Steel, Artisan, Steel Will, and many others owe something, I think, to Kizer’s precedent.

Buy the Kizer Begleiter at BladeHQ

Buy on Amazon

But after laying the template for the modern enthusiast knife – titanium frame lock, ball bearing flipper, trendy designers, sub-$200 price tag – Kizer seems to be fading into the background somewhat, getting drowned out in the bustling genre that it more or less established.

Which would be a shame, because Kizer has a lot to offer. While their various followers have gone up into the high high-end, playing with baroque stylings and highwire feats of machining prowess, or down into true budget territory, delivering good steel at great prices, Kizer has walked the middle ground. Their catalog mixes price-consciousness with smart, attractive designs, value with subtle flair and desirable designer pedigree. Kizer knives may not be flashiest or most fun, but they are often reliable, intelligently-designed, well-made and relatively affordable.

And speaking of well-made reliability and smart design, we come to the Begleiter. This knife has been around for some time and, although I don’t get the impression it was a massive immediate hit, it seems to have accrued some word-of-mouth mojo over the years; you definitely see it around. In part this can be chalked about to the impulse buy (for knife nerds) price tag, but also I think thanks to the (you guessed it) quality materials and solid, all-purpose design.

General Dimensions and Blade Details

The Begleiter has a blade length of 3.5 inches, an overall length of 8.125 inches, and weighs 3.8 oz. It is made in China and came impeccably fitted and finished. My particular Begleiter might look a little road-weary in the pictures, because it came to me at a time when I needed to do a lot of outdoors, yard-worky-type stuff. There’s a lot of unruboffable plant viscera on the blade, and some gunk in the pivot I’ve yet to wash out; but fresh from the factory, it was in pristine condition.

The Begleiter’s blade, a mid-sized drop point, doesn’t feel as long as it is, and it’s actually wider and stouter, blade stock-wise, than you’d think just looking at pictures of it. Flat ground, but not overly thin behind the edge, it’s a capable, durable slicer. I cut cardboard, paper, weeds, dug in pebbly garden soil, and accidentally banged the edge a couple times against brick; throughout it all the Begleiter cut well, and withstood my misuse with rugged stolidity. I actually like the look of the smoky gray titanium coating, and it held up well through the testing.

VG-10 – a good, good steel; I already knew I liked it, but I did learn one new thing about it in testing the Begleiter, and that’s that it can be relatively durable, despite its reputation for brittleness. As I said earlier, I smacked my Begleiter against bricks during multiple lapses in my bladesmanship. However, it only chipped at the very outermost, wafer-thin part of the tip, and there just minorly. I was impressed all over again. It’s not my favorite steel to sharpen up, but not so ornery I’d be hesitant to recommend it even to non-knife nerd users.

Handle, Ergonomics, and Pocket Clip

I’m not sure that Kizer still adheres to the old nomenclature for their various lines, but if they do the Begleiter falls into the Vanguard class, which means standard Vanguard handle materials: G-10 scales and stainless steel liners. On the Begleiter, those liners stand proud and letterbox the scales, and both scales and liners have been chamfered extensively.

Like the blade, the handle is less narrow in person than it looks in pictures, and the letterboxing on the handles injects dimensionality into the grip. Those proud liners are shiny-smooth, and the chamfering makes them feel almost crowned. The lone finger groove is well-proportioned, and the finger guard/pivot area doesn’t push your hand so far back that you feel like you lack control over the blade.

I don’t know who designed the Begleiter; I thought I found out the name of the man behind it at one point, but now I can’t seem to track that information down. So maybe I misremembered, or maybe it’s a Kizer in-house team effort; but either way the designer (s) deserve credit for a thoughtful ergonomic layout.

Less thoughtful, but by means bad, is the Begleiter’s clip. It doesn’t have a particularly appealing look, nor does it offer deep carry, and the contact point is right on the un-smooth G-10. That last point is one uncharacteristic bit of boneheadedness in the design of this knife. Granted, it’s an oversight most companies make, but it’s still disappointing. On the positive side, the clip’s tension is just right and it vanishes when you’re using the knife.

Opening and Lockup

Thumb stud and phosphor bronze washers: that’s the good stuff. This setup, combined with spot-on detent tuning, means the Begleiter’s blade pops into place when you flick it open – and you will be flicking it: a slow roll open is possible but this is a blade tuned to fly, and fly it does. I’m not much of a knife fidgeter these days but even sitting here writing the review I keep picking up the Begleiter and popping it open and closed. It’s fun, addictive, and most importantly reliable in use.

The stop pin is also plenty large and durable too; there’s nothing I dislike or would change about the opening configuration on the Begleiter and it’s one reason why I’m not at all interested in the new, premium, frame lock flipper Begleiters that recently released.

Here is a size comparison with the Spyderco Delica 4:

Are we past the age of dodgy lockups? I don’t remember the last knife I handled with a bad lock, or even a lock that has been anything less than great. Makers all around the world have been expected to Do Better in recent years, in no small part thanks to companies like Kizer setting new standards for quality in all price ranges.

Unsurprisingly, then, I have no complaints about the Begleiter’s liner lock. There’s still not an iota of play in any direction after many bouts of rugged and ungainly use. A cutout on the show side scale gives nice access to the locking leaf, and disengagment is as frictionless as the lockup is firm. Again, good stuff.

Kizer Begleiter Review – Final Thoughts

Let’s be frank: the Kizer Begleiter is not a knife that it’s easy to get excited about, here in 2019. Its materials are good, but not outstanding. The fit and finish is great, but so is the fit and finish on many, many other knives. The design is smart, but subdued almost – almost – to the point of colorlessness.

At $60 it’s a good value, but also sailing perilous close to the fatal Endura/Delica 4/Chaparral Lightweight Bermuda Triangle where other value-driven knife designs get lost forever. You struggle to find anything bad to say about the Begleiter, and use it approvingly, but it doesn’t endear itself in any singular way.

Which is maybe (definitely) a silly thing to ask a knife to do. If you’re looking for a good knife in this price category, this is a good choice, a smart choice even. If you have a friend who isn’t really into knives but could use one, this is one you could hip them to. I think this is money better spent than buying most Kershaws, for instance (although again, the shadow of the sub-$100 Spydercos looms large…).

In 2019, the Begleiter is a perfect synecdoche for Kizer itself. In the turbulent, baroque, saturated knife market, where we were spoiled for choice years ago and now we’re somewhere beyond spoiled, it can be easy to lose sight of Kizer. But they’ve maintained a steady output of sensible, solid, well-made and generally well-priced designs. You may not be wowed when you pick up a Begleiter, but you definitely won’t be disappointed either, and that’s worth something.

Kizer Cutlery Begleiter Folding Pocket Knife Liner Lock Green G10 Handles Knife, Kizer Begleiter V4458A2

A reversible pocket clip and stainless steel liners.
Tactical pocket folding knife offers rapid one-handed deployment, locks securely into place with liner lock
3.5" N690 blade with a drop point shape and gray titanium coating.The bronze washers allow for smooth blade opening
Handle Material:G10 /Blade Material:N690 /Weight:3.69 oz (0.23 pounds)
Overall Length:8.17 inch (20.75 cm) /Blade Length:3.58 inch (9.09 cm)

Editor: I recommend purchasing the Kizer Begleiter at Amazon or BladeHQ. Please keep in mind that purchasing anything through any of the links on this website helps support BladeReviews, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Victorinox Bantam Alox Review

by Seth Vietti 14 Comments

Victorinox makes the most popular pocket knives in the world. That’s not hyperbole, it’s just a fact: globally, Victorinox sells more folding knives than any other cutlery company and it isn’t even close. The Swiss Army Knife is an icon, lionized by media (MacGyver) and government (NASA) alike. They’re so well-known to be useful tools that the phrase “Swiss Army Knife” has come to represent the idea of multipurpose utility, itself.

Buy Victorinox knives at BladeHQ

Buy on Amazon

Out of the hundreds of Swiss Army Knife variants, the Alox Cadet seems to be the “gear geek” consensus choice for everyday carry: a winning combination of durable Alox construction, pocketable size, and useful tool selection. But what if I told you there might be an even better knife for the job in the Victorinox catalog? Allow me to (re)introduce you to the Alox Bantam.

General Dimensions & Blade Details

The Bantam, like the Cadet, falls in the middle of the current Swiss Army Knife (SAK) size range. At 3.3 inches (84mm) long when closed, it’s a sizable step up from their keychain models, but noticeably smaller than their “full-sized” pocket knives. Here it is between a Rambler (58mm) and an Alox Farmer (93mm):

Unlike the Cadet, which has a second backspring to accommodate separate can and bottle openers, the Bantam has a single tool for opening both nestled beside the main blade. This single-layer construction, coupled with skinny aluminum scales, makes the Alox Bantam literally wafer thin. Or, if you happen to have some Ritz handy, cracker thin:

The blade shape on the Bantam is quintessential Victorinox: a drop point with a slightly bulbous tip. Everything you’d expect a 2.5-inch slipjoint to do, this blade does well. There’s enough belly to make cutting on a board feel natural. It’s thin enough to cut with even after it gets a little dull (which it will, and fast). And while I do wish the tip was a little more acute, it’s not as blunt as it looks – it still pierced clamshell packaging with ease and cut out printed shipping labels with precision.

Victorinox doesn’t advertise their blade steel anymore, but it’s no secret that whatever they use doesn’t hold an edge for very long. Thankfully, it’s also inexpensive and impressively stain-resistant. For my money, it’s a compromise I’m willing to work around, especially since I’m usually carrying the Bantam alongside a larger and more capable folder. Plus, the steel’s softness / lack of wear resistance means you can maintain it on just about anything abrasive. For example: after the blade lost its keenness cutting two large cardboard boxes into strips small enough to fit in my undersized recycling bin, it only took a minute of stropping against that same cardboard to bring it back. Unfortunately, those sorts of tricks only work for so long before it’s time for a proper re-sharpening.

Handle, Ergonomics, & Pocket Clip

The first time I held the Bantam, I had to repress the urge to put it in my mouth to snap it like a chip. The waffled, wafer-like texture of its thin Alox scales coupled with its barely-there weight makes the Bantam feel more like a popsicle stick than a pocket knife. The more I used it, however, the more I came to trust it (and the less I subconsciously associated it with snacks). The riveted all-metal construction is rigid and the handle texture, while not aggressive, provides some traction even when wet.

Measuring in at 3.3 inches long, the handle of the Bantam is long enough to wrap all four fingers around, but thin enough that I wouldn’t really want to bear down on it. It’s practically two-dimensional: whichever tool you have unfolded, the handle presents as a simple, flat, oblong shape. Not exactly comfortable, just impossible to hold incorrectly. Once you get used to its exceptional thinness the Bantam basically disappears in use, allowing you to focus on the task at hand instead of how you’re holding the tool.

I avoid carrying anything loose in my pockets if I can help it. So, with neither pocket clip nor lanyard loop to anchor it from twisting, swinging, or knocking around in there, the Bantam was not something I expected to enjoy carting around. To my surprise, I struggled to notice it was even there. It’s hard to overstate just how slim and light this knife is – I’ve pocketed CVS receipts bulkier than the Alox Bantam.

Deployment & Lockup

The backspring tension on the Bantam is well-balanced: strong enough to keep the tools firmly in place when open, but not so strong as to make them awkward to unfold. Opening either one is always a two-handed operation. After more than a year of use, neither tool has developed any play, though they’ve picked up a fair few scratches.

Equipping a pocket multi-tool with a dedicated can opener has always been baffling to me. Even if we set aside the fact that pull-tabs on cans have become ubiquitous, I can think of a dozen other tools I’d need before encountering a single unopened can. Victorinox clearly disagrees, because nearly every full-sized SAK includes a can opener. Here on the Bantam it’s been cleverly integrated into a “combination tool,” which also lifts off bottle caps…

…drives screws…

…and scrapes, prods, and pries if need be.

It’s become my favorite Victorinox tool by far, and it makes the perfect companion to the Bantam’s light-duty blade. It’s not a crowbar or an impact driver – obviously – but in the daily struggle against encroaching entropy, the combo tool is often enough to tweak, tighten, or undo the issue on the spot without a walk to the toolbox.

Victorinox Bantam Review – Final Thoughts

Goldilocks would agree with me: the Bantam is just right. The keychain-sized SAKs are useful to have around (who doesn’t love those tiny scissors?), but far too feeble to replace a dedicated knife. The larger SAKs are also great, but tend to be loaded with tools I don’t use often enough to justify carrying them around all day. The Bantam is just enough knife for most cutting, plus it’s capable of work that a blade alone can’t (or maybe just shouldn’t) do.

I don’t think there’s another knife on the market that packs so much utility into such little mass. For me, this is where the Bantam really pulls ahead of the Cadet as a daily companion: it offers 80% of the functionality at half the size. Unless you absolutely need a nail file or can’t live without a lanyard, the Bantam wins by sheer efficiency. And even though the Alox variant is about $10 more than the red plastic-handled Bantam, the durability, grip, and next-level thinness the Alox scales provide are well worth the upgrade.

Some, I suspect, won’t see the Bantam’s ultra-minimalist design as a selling point. If you’re looking for a multi-tool that’s more “off-road” than “office,” I would point you elsewhere. But if you’re looking for a polite companion to a larger knife, or want the multipurpose utility of a Swiss Army Knife without any extra frippery, I would enthusiastically recommend the Alox Bantam.

Victorinox Bantam Alox Swiss Army Knife, 5 Function Swiss Made Pocket Knife with Large Blade, Screwdriver and Bottle Opener – Silver

A CUT ABOVE THE REST:Compact, agile and ready to face any adventure head-on. Our range of Swiss Army Knives have been established since 1897 and continue to be an icon of utility and smart design.
DURABLE CONSTRUCTION: Swiss made stainless steel construction encased in our popular scales offers a slimmer profile and is extremely resistant.
COMPACT CARRY: Bring this knife with you on your daily adventures without sacrificing space.
FIT FOR ALL TASKS: At their heart, all our pocket knives are a survival tool; multitaskers that deliver in any situation. At their most evolved they have surpassed basic function to pioneer space travel and restart engines.
TRUSTED QUALITY: Made in Switzerland; Victorinox provides a lifetime against defects in material and workmanship. Making a lifetime commitment has never been so easy. No assembly required, money back guarantee.

Editor: I recommend purchasing the Victorinox Bantam at Amazon or BladeHQ. Please keep in mind that purchasing anything through any of the links on this website helps support BladeReviews, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Spyderco Para 3 Lightweight FRN Review

by Dan Jackson 6 Comments

The Spyderco Paramilitary 2 may be the most popular knife in the last 20 years. It’s received near universal acclaim, and is revered by knife collectors and users alike. So when Spyderco released the Para 3 a couple years ago it was a big deal. Ben reviewed the Para 3, and he did a great job.

Buy the Para 3 LW at BladeHQ

Buy on Amazon

The Para 3 had some big shoes to fill with the Paramilitary 2. It may have come up a little short. Others seem to share Ben’s opinion. The Para 3 isn’t quite as loved as the original Para 2 for some reason, but it has still developed a loyal following and already boasts a number of sprint runs.

I never bought the Para 3, but felt like I should have. So when then the Para 3 Lightweight came out I bought one on the spot from GP Knives.

As a short aside, GP Knives is smaller than my usual preferred retailer, BladeHQ, but they have the knife in stock, offer fast shipping, and have a great Twitter account that has convinced me to make more than one impulse purchase.

I figured the Para 3 LW would allow me to gain some perspective on the Para 3, but also provide a knife that I could review on here. I should also note that this knife is also referred to as the Para 3 FRN.

General Dimensions and Blade Details

The Para 3 Lightweight has an overall length of 7.27″, a 3.00″ blade, weighs 2.4 ounces, and is made in Golden Colorado, in the United States of America, here on planet Earth. This is a Sal Glesser design. For those that may not know, Sal is the founder of Spyderco.

The knife feels exceedingly light for its size. I let my dad handle it a couple weekends ago and his comment was that it was “very lightweight.” You can always count on BladeReviews for the deep insights.

I’m no stranger to Spyderco’s lightweight designs. The Native 5 LW and Dragonfly 2 in FRN remain stalwarts in my collection, and at the top of my Best EDC Knives list.

Spyderco’s lightweight versions have gained traction for good reason. You get the same cutting performance of their heavier knives at a fraction of the weight. While the knives won’t be quite as strong, they are still serviceable for normal use. They are great choices for every day carry.

The blade on our Para 3 FRN is a classic Spyderco shape. It’s a shrunken down Para 2 blade. It’s taller and stubbier. It’s broad with a full flat grind. No swedge, no sharpening choil. It’s simple, but it works. The low tip is sharp and good for piercing. The low belly is fine for slicing. This may not be the best skinning knife, but I’m not a hunter.

Here’s a size comparison with my Para 2:

Spyderco selected CTS BD1N for the blade steel. I was a little surprised by this choice, figuring they would have went with S35VN. But they decided on CTS BD1N. This is a less expensive blade steel, which I’m sure helps keep this knife retail for less than $100. In my experience it’s a very easy steel to sharpen. It takes an edge quickly on my Golden Stone. The blade is capable of getting razor sharp and it tracks through cardboard without a problem. No issues with rust or corrosion so far.

I’ve used my Para 3 Lightweight extensively as a daily carry knife. This means I’ve opened lots of mail with it, broken down plenty of boxes, sliced and diced fruit while watching the last season of Game Of Thrones, and accomplished a myriad of small chores that require a sharp edge. I can’t complain about the blade shape or the blade steel. The full flat grind provides good slicing performance. The edge retention is decent.

When it’s time to sharpen up the knife it comes back quickly. It’s one of those fine grained steels that you can feel get sharper on the stone. Personally, I like knives that are easy to sharpen. I maintain my edges regularly and would rather touch up often then need to spend a half hour bringing back the edge on a knife with stubborn steel.

Handle, Ergonomics, and Pocket Clip

This section is presumably why you are checking out the review. The handle of the Para 3 Lightweight is made of fiberglass reinforced nylon (FRN). That’s a high density plastic. There are no metal liners in the knife. The compression lock is just a small strip of steel. There are 2 substantial FRN standoffs near the tail of the handle, and the lanyard hole is reinforced, presumably to provide some structural rigidity to the handle.

Some may be skeptical of a plastic handled knife, but Spyderco has proven themselves before with their LW series, and I think it works here with the Para 3 as well. The handle is secure. There is a tiny bit of flex in the FRN if you try to squeeze the handles together, but it’s not bad. Everything appears to be well engineered.

“Engineering” is a term that has only recently come in vogue within the knife industry, but with a knife like this you can’t just slap it together. It takes a good deal of engineering to pull something like this Para 3 lightweight off. This becomes especially apparent when you take the knife apart (more on that later).

A major concern when you try to shrink down a knife, is how that will effect the ergonomics. The handle of the Para 3 is almost half an inch shorter than the Para 2. That’s significant for a knife, and could result in some ergonomic compromises.

All in all, I think the Para 3 is pretty good ergonomically. There is still enough room for a full 4 finger grip without using the forward finger choil, and the heavily contoured FRN feels good in hand. There is plenty of traction thanks to sharp jimping, and Spyderco’s bi-directional textured handle. This one won’t slip out of your hand in the shower.

However, there are a couple small ergonomic issues. First of all, I’m not a huge fan on the small “beak” on the tail end of the handle. My pinky lands directly on it. While the beak isn’t sharp, all things equal I’d rather not have it right there. Or at least see it smoothed out. If you have smaller hands I think you will be fine, and it may actually help you grip the knife better. For larger hands the beak gets in the way. Also, there are some slightly sharp edges on the inside of the FRN, especially up by the compression lock. Nothing that will cut you, but it’s noticeable and I want to point it out. It could easily be smoothed over with emery paper if it bothered you. I don’t notice it in use, more when I’m examining the knife.

All said I think the ergos are pretty good on the Para 3 LW. I’d lose the beak and maybe soften some edges, but beyond that there is little to complain about.

The Para 3 LW is equipped with the Spyderco wire clip that can be mounted for ambidextrous tip up carry. It’s a deep carry clip that has been positioned so that it buries 99% of the knife in your pocket. It’s a simple and elegant design, and continues to be a personal favorite. I’ve owned the Dragonfly 2 for almost 10 years now. It has a similar type of clip and have never had an issue with it.

I also view this clip as an upgrade over the standard spoon style clip found on the Para 2 and the original Para 3. It’s deeper carry and more discreet. They should implement this clip on the entire Para family.

The knife carries wonderfully. At 2.4 ounces, you don’t feel it in the pocket. It disappears and you quickly forget about it. It’s a great choice for daily carry for this reason. It stays out of the way until you need it. Can’t say enough good things about how this knife carries.

Deployment and Lockup

The Para 3 makes use of a 13mm thumb hole. This is the same size as the Para 2. This oversized thumb hole is easy to engage with your thumb or middle finger, and the blade flicks out easily. This begged the question of whether there were washers inside the knife. I peered inside and couldn’t see anything, so I took the knife apart with my WiHa drivers. Here is what I found:

Oddly enough there is only one phosphor bronze washer on the lock side over a steel plate. On the other side it’s just raised plastic. This could be a turn off for some, but I wasn’t too surprised given the construction of my Native 5 LW.

For lockup we have a new version of the tried and true compression lock. In the past, the compression lock has been integrated into the liner of the knife. Here, it’s a small stand alone piece. Here are a couple shots with the lock engaged and disengaged:

I think they successfully integrated the compression lock into the knife. It feels just as good as my Para 2. There is no lock stick. It’s easy to disengage, and provides the strength and convenience we have come to appreciate from the compression lock. No blade play or wiggle. No complaints.

Some may find the lack of metal inside this knife concerning. They want something more substantial. I haven’t noticed an issue. Again, the knife feels solid. I think with normal use you will be fine. I probably won’t take this one hog hunting, but it did a great job opening a bag of coffee the other morning.

Here is a shot of the Para 3 LW compared with my Spyderco Sage 5:

Blade centering is perfect on my piece. Even after disassembling the knife everything came back together smoothly. Again, I think it speaks to the engineering put into this knife. Gone are the days of guesswork hoping that tolerances are good enough that the blade will center. This thing just plain works.

Spyderco Para 3 Lightweight vs. Benchmade Bugout

Another interesting comparison is with the Benchmade Bugout. Both are ultralight full size folders. Both are made in the USA. At the time of writing this article the Bugout costs about $30 more. Here’s a size comparison:

As you can see they compare favorably in terms of overall length and handle length. The Bugout has substantially more cutting edge thanks to the lack of a finger choil, and it’s significantly lighter at 1.8 ounces vs. 2.4.

Personally, I like the Bugout a little more. I like the blue accents, Benchmade’s heat treat on the S30V blade, the ultra thin blade grind, the roomier handle, and the axis lock. But averaged out for cost I’d say they are close. Both are nice knives. Buy what you like.

Spyderco Para 3 Lightweight Review – Final Thoughts

Objectively I think the Para 3 Lightweight is another winner from Spyderco. It’s lightweight, highly functional, and embodies many of things we love about Spyderco knives. Plus it’s made in the USA and retails for under $100. In an era of expensive overseas made knives, the Para 3 LW is a compelling proposition. Personally, I see no reason to have the original G-10 version over this lightweight version, unless you want to collect them. This lightweight version will cut just as well. Maybe you sacrifice a tiny bit of strength, but unless you plan on batoning with your folder I don’t think there is much cause to be concerned.

If I had to some nit picking, it would mostly be directed to the small hump at the base of the handle near the pommel. I found that got in the way a little. Not enough to develop a hotspot, or make the knife unusable, but I didn’t care for it. Also, there are some slightly sharp edges on the insides of the handle. Nothing crazy, but again, I want to point it out. Some might gripe that the knife is “too” lightweight with only a single washer, and very little metal inside the hande. I’d suggest buying a regular Para 3 in that case.

Beyond that, a sharpening choil wouldn’t hurt, but you don’t see those on may Spydercos with this leaf blade shape. I can sharpen the entire edge if I use a rod style sharpener like the Sharpmaker. Spyderco has spent a lot of time considering their designs, and the Para 3 LW is well considered. I find it hard to fault the knife in any major way.

But I will take this moment to talk about the Spyderco line in general. They have so many good knives. Would I pick this one over the Sage 5 or the Native 5 LW or the Chaparral FRN? Frankly I don’t know. Every year Spyderco’s catalog grows more crowded. Some are cool collaborations for collectors that probably will come and go, but others like this Para 3 LW will be permanent editions.

For example, you have the Endura, the Delica, and now the Endela. And that’s in addition to the Stretch, Dragonfly 2, and everything else in that family of knives. It’s a lot to consider. It has become cliche to say we are “spoiled for choice”, but we really are. There’s a lot of good stuff out there. How do we decide? The Para 3 doesn’t make it any easier. It’s another great knife.

Personally, I think I like it more than my regular Para 2. The Para 2 will never leave my collection, but I like how the Para 3 FRN has a smaller, lighter footprint, and I also like the deep carry clip. The ergonomics are a little better on the Para 2, but unless I’ve got a big job ahead of me I’d rather have the smaller knife. The Para 2 remains a beast and will be a great choice for bigger jobs or those days when I want a meatier knife, but for most days I think the Para 3 LW will fit the bill.

Spyderco para 3 Lightweight Signature Folding Utility Pocket Knife with 2.92" Stainless Steel Blade and FRN Handle - Everyday Carry - PlainEdge - C223PBK

The New EDC: The Para 3 distills all the features of that best-in-class folding knife into a more compact, carry-friendly package. It proudly features all the key qualities of the Para Military 2 with a full-flat-ground CTS BD1N Steel Blade.
Superior Quality: Machined from premium CTS BD1N, a nitrogen-enriched high-carbon chromium steel, the Para 3 offers superior balance, edge retention, and low-friction cutting performance.
Pocket-Friendly: It features a lightweight, open-backed construction style and its Stainless Steel liners are nested into the FRN Handle. This reduces handle thickness and provides excellent support for the knife's Compression Lock.
Reliable High Performance: The Para 3 traces its history all the way back 2004 to the introduction of the Para Military design. It offers the same proven reliability and cutting performance, but in a more compact, easy-to-carry design.
Easy-to-Use Lock: Located in the spine of the handle, the Compression Lock's high-strength mechanism locks the blade securely open during use, yet allows it to be closed easily and safely with only one hand.

I recommend purchasing the Paramilitary 3 at Amazon, BladeHQ, or GP Knives. Purchasing anything through any of the links on this site helps support BladeReviews, and keep this review train running. As always, any and all support is greatly appreciated.

Bestech Knives Malware Review

by John Burridge 4 Comments

Over the years, I’ve noticed that in polite society when I whip out a folding knife to open a box or cut a loose thread, most people’s reactions are some variation of “Oh God, why do you have/need/carry that?” My usual reply is that a knife is the most useful tool in the world, but I’ve found that no matter how “non-threatening” looking the knife is, I still get that same reaction. Therefore, why not carry whatever I want?

Buy the Bestech Malware at BladeHQ

So, a month ago I put down my already scary-looking Microtech Ultratech OTF switchblade and picked up the seriously murder-ey looking Bestech Malware.

The Malware was designed for Bestech Knives by Todd Knife and Tool. TKT was started in 2016 by prolific knife reviewer Teryl Todd (Zelrick42 on YouTube) and his brother Seth Todd. They went from being fans to designers, and have a thoroughly modern company. Teryl lives in Ozark, Missouri, and Seth lives in Houston, Texas. They jointly design their knives by sharing 3D CAD files online, then Seth makes physical prototypes that they both test. TKT have developed a distinct visual style also apparent in their We Knife Co. made Roxi folder, and in the many prototype images shared on the toddknifeandtool Instagram account.

General Dimensions & Blade Details

The Malware’s blade is 3.875” (9.8 cm) long, the blade stock thickness is 0.15” (3.9mm), and it’s full open length is 8.75” (22 cm). The long stabby blade folds into a titanium handle, the blade pivots on ball bearings, and it’s framelock has a steel lockbar insert. The steel lockbar insert is a theoretically replaceable part that protects the titanium framelock from rubbing against the lock face of the steel blade. My experience has been that often a titanium framelock rubbing against a steel blade tends to “stick” in place, but steel on steel doesn’t have the same problem.

Here is a size comparison with a large Sebenza Insingo:

It weighs 3.68 oz. which is technically a little more than a Spyderco Paramilitary 2 or a Chris Reeve Knives large Sebenza, but it feels lighter than either of them in the hand. I attribute this feeling to the weight balance of this knife. If I’m holding the Malware in a normal thumb-on-top grip, and I slowly open my hand, the knife will not fall to the floor, but will stay balanced on my index finger. This nearly perfect weight distribution helps the Malware feel very agile in my hand.

The titanium pocket clip is configured as a right side, tip up only, but there are dedicated left handed versions as well. I have the “Ti Black” version. The titanium backspacer and pocket clip are anodized a brassy gold color, and contrast nicely against the black stonewashed finish of the rest of the knife. The stonewashed treatment gives the edges and corners a worn-in look similar to Kershaw Knives’ “blackwash” finish.

It’s blade steel is S35VN, which was developed specifically for high-end knife blades by steelmaker Crucible Industries and Chris Reeve Knives. It’s a powdered metal steel, which has the advantage of more uniform blending of it’s elements (iron, niobium, chromium, vanadium, etc.) than conventional steel. The end-user benefits of this manufacturing process and the S35VN formula are excellent blade toughness (it can take a hit without breaking or bending), corrosion resistance, and edge retention.

So it’s a modern production knife made in China with premium materials and it’s priced accordingly at $196 on BladeHQ. What makes it different than every other new Kizer, Reate, We, and Rike knife? Style and details.

What I love about good pocketknives is that they’re pieces of functional art you can hold in your hand. The Malware is full of interesting details and I keep noticing more. The design is a strange futuristic combination of curves, straight lines, and, as on the cutting edge of the blade, straight lines that almost imperceptibly turn into curves. The blade has a finger choil which, although it’s a little too small for my index finger, is the full 3.9mm width of the blade stock, which is yet another design detail that I appreciate.

Handle, Ergonomics, & Pocket Clip

In pictures, the handle looks very thin, and in the days between ordering the Malware and receiving it, I wondered if it would be too small to properly wrap my medium-large-ish hands around. When it arrived, I found that it fills my hand very well, and the long, flat clip doesn’t create much of a hotspot any way I hold it.

Some edges are pretty squared off, like the machining on the backspacer, but almost every part of the handle that comes in contact with my hand is chamfered, making it quite comfortable to hold. And the more I have it in my hands, the more I keep discovering new functional design details that I had, at first glance, written off as being cosmetic- like the three holes in the show side near the flipper tab. Those holes are exactly where my right thumb needs traction when flipping the knife open.

On the lock side of virtually all framelock knives, there’s a machined indentation in the frame that allows the locking part of the frame to flex inward and lock the blade open. A lot of knives cover this indentation with their pocket clips, but as yet another example of how well thought out this design is, the pocket clip on the Malware sits right above, but not covering, the indentation. So when gripping the knife to flip it open, my ring finger is naturally pushed into that square indentation, which gives me a secure grip when flipping it open.

I don’t ordinarily use my pocketknives for food prep, but in the spirit of thoroughness I sliced up some veggies with it. The blade has a full flat grind and gets very thin at the bottom, which made slicing easy. The ergonomics for general food prep were fine as long as I didn’t try to spread anything- the thin blade definitely doesn’t work as a butter knife. The flipper tab extends below the cutting edge, so it can’t really be used for dicing either, but kitchen work is clearly not this knife’s intended use.

The pocket clip is rather long and thin and has more flex to it than any other milled clip I’ve handled. The good news is that it doesn’t chew up my (already chewed up) pants pockets, but the bad news is that it seems like it could easily get bent.

I carried this knife during a T.C.C.C. medic class, and when we were learning how to improvise tourniquets, I used the Malware as a windlass (the stiff piece that you twist to tighten the tourniquet.) Despite really cranking this thing down tight on my training partner’s arm, I had no fear of the knife breaking or bending until the instructor decided to show the class how to tie off the end of the improvised tourniquet using the pocket clip. He was bending the clip way out and jamming fabric under it, and I desperately wanted to ask him to stop so he didn’t break it. I resisted this urge because I didn’t want to seem like a weenie to our super-badass Los Angeles SWAT Medic instructor. So he manhandled the clip, and when he was done, it just sprung back to it’s normal state. It may be thin and flexible, but it’s not fragile.

Overall, the Malware isn’t an “overbuilt” knife like a Hinderer Knives XM or a Strider SMF, but it’s definitely tougher than it looks.

Deployment & Lockup

A gripe I have with every single framelock flipper is if I grip it in such a way that I’m putting a lot of pressure with my middle finger on the front of the lock near the pivot, then the knife becomes very difficult to flip open. The worst offender on this front that I have is a Brad Zinker midtech version of the Boker Urban Trapper. The only knife I have that is immune to this problem is my GiantMouse GM1, which is an awesome knife overall, but perhaps solves this problem by having a weak detent which makes it difficult to flip open. However, the ergonomics of the Malware naturally place my fingers where they don’t get in the way of the mechanism at all.

The Malware’s flipper tab is relatively small but has comfortably rounded jimping that provides good traction for flipping. The amount of detent tension that has to be overcome to flip the knife open is tough for me to objectively define- but subjectively, I think it flips perfectly. The Malware’s framelock engages at about 40%, which you can jam over to about 60% if you’re worried about it slipping (not that that’s ever happened to me or anyone I know.)

I don’t carry a knife specifically for self defense, but I must say that I certainly never felt under-prepared while carrying the Malware on the weird streets of Los Angeles. It’s never accidentally opened while in my pocket or while drawing it out of my pocket. It’s flipped and locked open securely every single time I’ve flipped it. I don’t think an especially scary-looking knife like this is going to make a bad man run away in terror, but it’s a long, mean looking blade with a big handle I can get a very firm grip on. So I’ll add self defense to the Malware’s growing list of positive attributes.

Bestech Malware Review – Final Thoughts

I carried the Malware every day for a month and primarily used it for un-challenging tasks like opening packages, slashing open bags of cat food, and as an improvised medical device. At the end of the month, the finish on blade, handle, and clip are unblemished. The S35VN blade was still very sharp in most places, but after a quick, ham-fisted touch up on a Wicked Edge sharpener, it’s back to 100%. There’s no sharpening choil, but I don’t really care if the last few millimeters of my blade are super sharp.

What is the Bestech Malware made to do? I don’t want to sound like a knife snob a-hole, but I tend to compare everything to my Chris Reeve Knives Sebenza 21. The word “Sebenza” is literally the Zulu word for “work”, and the Sebenza feels like an indestructible precision tool. The Bestech knife doesn’t feel like a tool, it feels like a blatantly offensive weapon that can also open boxes from Amazon. Malware is the perfect name for this knife because it’s so badass. Not flaming skull badass, but sci-fi villain badass. It brings to mind futuristic heavy metal music by the band Voivod, it’s like the knife version of the Space Marines’ rifle from the movie Aliens, it should be a weapon in the DOOM video games, and I obviously really like it.

The deciding factor for anyone considering buying the Malware is definitely it’s looks- if you immediately like it’s vibe, I say get it. Nothing is perfect (except kittens), but the Malware excelled at everything I wanted it to do, and looked super-murder-ey doing it. Recommended!

Bestech Knives Malware – From $196.00
From: BladeHQ

Editor: I recommend purchasing the Bestech Knives Malware at BladeHQ and Amazon. Thank you very much.

About the Author: This guest review was written by John Burridge. John lives in Los Angeles and has a deep passion for knives. I plan on adding to this section to include more info about John and where to find him. In the meantime, I hope you enjoyed this in depth review.

Hardcore Hardware Australia MFE01 Rhino Review

by Andrew Gene Leave a Comment

The Hardcore Hardware Australia MFE01 Rhino is a medium sized utility tool. It was designed by Australia based tool manufacturer Hardcore Hardware in conjunction with SOER, the Special Operations Engineer Regiment which supports the Australian Special Operations Command or SOCOMD. SOER specializes in Chemical, Biological, Radiological, Nuclear and Explosive (CBRNE) threats.

Buy the MFE01 Rhino at BladeHQ

No products found.

Their expertise also makes them an integral part of the Tactical Assault Groups (TAG) that were formed after the September 11 terrorist attacks that occurred in the US. With bases in east and west Australia, TAG is a quick response, domestic, direct action (offensive) counter-terrorism entity.

General Dimensions and Blade Details

The Rhino is made from a massive piece of D2 that’s just over 5/16th” (8mm) thick 12.6″, in length and 6.7″ at its widest. The total weight is 27 oz. To maintain ductility (toughness) during impact, the D2 has been heat treated to a lower hardness between 53-54 HRC. This seems sensible, being in the same range as similar sized, impact/chopping tools that have been around much longer such as hammers, axes etc..

Since D2 is a semi-stainless steel, HHA has coated this, and all their gear, with a thick black, low glare PTFE coating (teflon). The Rhino is also be available in a tan PTFE coating. The company’s logo and model name is etched on one side of the head and the Hardcore Hardware Australia word-mark and steel type appears on the other.

The MFE01 has three main tools. The front of the head has a bladed edge. This is different from the typical tomahawk as it has a much smaller cutting surface. The design focuses the impact force in a smaller area for a concentrated strike. With a steep bevel, it is proficient at splitting tasks. This geometry would be less likely to get stuck in softer materials like wood where a thinner blade is prone to.

The poll (back of the head) is claw shaped for use as an impact or prying tool. The point isn’t sharpened which, is probably a good choice to help prevent self injury when bearing down on the handle.

The back edge is rounded like a claw hammer to improve mechanical leverage and has a row of jimping that grabs the opposing surface when in use.

The jimping also adds traction when manipulating the third tool, the crowbar like pommel. This has a shallow angle resulting in a narrow tip that can be easily wedged into small spaces. A notch in the face will handle a variety of nail sizes making the Rhino great for opening crates or similar jobs.

Handle

The handle on the Rhino is somewhere in between a full and partial tang. Because the tang travels out-to and beyond the scales it could fall into the full tang category. Alternately, large slots cut out of the center for weight reduction, may argue the latter. Regardless, the 5/16th inch thickness coupled with the conservative hardness should make this tool difficult to break.

While the handle slots improve weight they can incidentally be used as large shackle wrench or to thread 550 paracord for added traction. A paracord wrap could also be an alternative handle covering if you remove the scales. The thick G10 slabs echo the tang’s slots, sharing the same weight saving, grip-adding properties. Traction is further improved with a peel-ply texture. The scales are attached with large torx fasteners and come in a brown or black color. Holes at the base of the head and pommel can be used to form a d-lanyard for extra security.

While the slots are great for grip, the over-all handle feels a bit boxy and is probably much more comfortable when wearing gloves. It would be nice to see some contouring for added comfort. Additionally the slots make the Rhino resonate, making a pinging sound when using it, especially when striking something with the head’s flat. Sound probably won’t matter to most though, seeing as the Rhino doesn’t tread quietly. Despite these criticisms the over-all dimensions and weight distribution make it feel nimble and controllable when leveraging all the tools.

Sheath / Carry

For carry the Rhino comes with two options. The first is a large 1000 denier Cordura pouch. This seals with a velcro flap and snaps, completely enclosing the tool.

The back side has a ladder of PALS webbing and a full length strap with a snap making it MOLLE compatible. The front side also has a ladder for attaching other equipment. An eyelet at the top corner and base allow for cord to be tied on, making a handle or sling.

The second option is the Kydex ‘Speed Scabbard’. As the name implies, it is designed for quick access. The scabbard only holds the head, leaving the handle exposed for release. This works by pulling downward with a back sweeping movement, releasing the blade then the claw. The motion is easy and natural.

Likewise, the head is stowed by putting the claw in first and then clipping in the rest by pushing upward. Retention is great and further enforced by a rubberized snap ensuring a secure closure. The system attaches via double MOLLE-loks.

Hardcore Hardware Australia MFE01 Rhino Review – Final Thoughts

The MFE01 Rhino is a comprehensive tool cooperatively designed with professionals for their use. The robust build quality, premium materials and useful tool set make it a durable companion capable of taking on a wide variety of hard-use tasks. Two carry options further extend the versatility of this moderately compact yet powerful package.

While finishing details are much less important than utility on any serious gear, the company has still paid good attention to the fit and finish. All in, Hardcore Hardware Australia has created an interesting variation of the modern tomahawk, adding positively to the overall offerings in this category.

No products found.

Editor: I recommend purchasing the Hardcore Hardware Rhino at Amazon or BladeHQ. Thanks for reading.

Additional Specifications

Steel: D2
Finish: PTFE (Teflon) Available in Black or Tan
Total Length 12.6″ (320 mm)
Total Width: 6.7″ (170 mm)
Thickness: .315″ (8 mm)
Weight: 27oz (765 g)
Handle: Brown or Black G10
Country of Origin: Australia

Sheaths:

1000 Denier Cordura®
Speed Scabbard
MOLLE Compatible

The Rhino is distributed by sharpernow.com in the US.
For more on Hardcore Hardware Australia, visit http://www.hardcorehardware.com.au