Benchmade

Benchmade Mini Boost Review

As a rule of thumb, most knife nerds steer clear of blades with assisted openers. They’re regarded as obnoxious, tough to maintain, and not as prestigious as something with a truly dialed in detent. But can you guess which type of folks tend to prefer assisted openers? In my experience, the answer is simple – Those who actually use their knife as an everyday tool.

Buy the Benchmade Mini Bost at BladeHQ

Buy on Amazon

This brings me to the Benchmade Mini Boost. I know about AXIS Locks, but I’d never handled an assisted one. So, when the company offered to send one over for review, I leapt at the opportunity. Here’s my review of the Mini Boost, a blade which just might change the way you think about spring-fired knives.

General Dimensions and Blade Details

As its name would indicate, this is the compact version of Benchmade’s USA-made Boost design. It sheds nearly an inch and a half of its predecessor’s length, now reaching a modest 7.18-inches open. Blade span has been reduced from 3.7-inches to 3.11, while slimming the stock from 0.12-inches to a demure 0.10. The CMP-S30V steel remains the same, as does its drop point, flat ground nature. Last is the weight, plunging from 4.59-ounces to 3.31.

Enough numbers. Let’s flick the thumb stud, fire the AXIS Assist, and get to business.

As you can see from the cutting board photos, the Boost’s thin blade is an excellent slicer. Despite its American roots, the knife proved invaluable in the preparation of homemade General Tso’s Chicken. I had no trouble producing finely chopped pieces of ginger, garlic, and green onion. It proved equally capable in other daily chores, breezing through bags of dogfood and those annoying boxes for the toner cartridges at work.

This does bring up something of a sore spot. When you use things, they tend to get dirty. I like to maintain my tools, which usually involves some form of disassembly and cleaning. The Mini Boost, however, will get no such treatment from me. AXIS locks are fiddly to take down in the first place, but add in what I assume is some form of torsion bar or coil setup and, man, I don’t need that kind of frustration in my life. The bronze washers are easily accessible, and a periodic application of oil may be all you need to keep it firing reliably.

Speaking of reliability, I must have picked a good time to start reviewing Benchmades. While I’ve heard and read many complaints about their production and quality control, each of the three blades I’ve handled had zero problems. Maybe they’re closely monitoring the reviews samples, but I have nothing negative to report.

Handle, Ergonomics, and Pocket Clip

First impressions count for a lot, but they can also be deceiving. Take the Mini Boost’s width, for instance. My immediate in-hand reaction was, “Wow, this thing is thick.” And it is: 0.63-inches from a statistical standpoint. But take a look at this side-by-side comparison with the Spyderco Native 5.

See that? The spines are pretty much identical, though the Boost’s sides swell out a bit further. In the pocket, this width is surprisingly comfortable. Part of this is due to its excellent deep-carry clip. The knife rides low in the back of my pocket, where its girth actually puffs out the seam and makes the rest of my tools more accessible. I prefer thinner knives, sure, but this slightly wide feel also helps with grip. The polymer scales are a perfect pairing, though they can accumulate a bit of pocket grit. Still, I consider this to be an acceptable hazard for a work-first blade.

Let’s revisit the assist. Because of its sensitive thumb-stud deployment, Benchmade has included a safety switch above the AXIS Lock. This sends a piece of metal sliding into the mechanism, preventing the knife from accidentally deploying in your pocket. While I applaud their prudence in including this safety measure, it does cut down on some of the quick-fire appeal of an assisted blade. It leaves me wondering if assists and AXIS Locks are really meant to go together. It works, but the process definitely takes some getting used to. And while you certainly can carry it with the safety retracted, I was never quite comfortable with the idea of a loaded blade in my pocket.

That being said, management of the AXIS Assist quickly becomes second nature. I carried this blade for nearly a month before completing the review, during which time I grew to appreciate both its deployment quirks and slicing prowess. One-handed closing is tricky, sure. But I kept fidgeting with it, over and over, just for the satisfying SNAKT noise of the blade leaping into place. For all its added complication over something like the Kershaw SpeedSafe, this assist is much more fun.

Benchmade Mini Boost Review – Final Thoughts

Let’s close with a thought experiment. Imagine you’re working a manual labor job in a dusty, grimy environment. Would you prefer a slick-firing folder running on ball bearings or an easy-opening blade sandwiched between phosphor bronze washers? For me, the answer is simple – Assist all the way. Because, sweet as that bearing action may be, it’s only a matter of time before job site gunk finds its way into the action. The solid washers and spring will run faster, longer, and more reliably in most hard-use situations.

As such, I consider the Mini Boost to be a solid argument for the existence of assisted knives. This, along with the Zero Tolerance 0566, is a solid example of spring-fired excellence. Yes, it’s trickier to maintain. But when it comes to down and dirty work, most of the calloused-handed folks I know prefer a blade with fast-deploy capability. I can’t tell you how many Kershaw Leeks and Ozark Trail folders I’ve seen peaking above the pockets of coveralls and dusty jeans.

In the end, the Boost proved to be a perfectly acceptable single-solution knife. It carries easily, cuts like crazy, and holds a decent edge. I’m still perplexed by the sudden resurgence of S30V, and I’d certainly prefer a better steel at this price point. But aside from the S30 and its pudgy width, there’s not a lot to dislike here. While I still prefer the mechanical precision of a dialed in detent, I’m also not the sort of hard user who cuts through boxes and bags all day. If that’s you, then consider checking out the Benchmade Mini Boost.

ESEE Knives Black CANDIRU Fixed Blade Knife w/Polymer Sheath

I recommend purchasing the Benchmade Mini Boost at Amazon or BladeHQ.

Benchmade Proper 319 Review

by Aaron Shapiro 1 Comment

Two or three years ago if you told me that Benchmade was your favorite knife company I’d roll my eyes and mutter something like, “Okay Griptillian dude…” now, that’s no disrespect to the Grip, those are great knives at a great price point, but they’re kinda vanilla for my tastes. That was Benchmade a few years ago.

Buy the Benchmade Proper at BladeHQ

No products found.

I’m not sure what happened over at Benchmade HQ but man are they putting out some absolute HEATERS in the last year or so. Starting with the Benchmade Proper slip joint (reviewed here) to the Benchmade Bugout and the full titanium integral Anthem 781.

Now, the slip joint thing is kinda interesting. Over the 2-3 year period, slip joints have begun to increase in popularity with the “tactical knife” folks. With the growth in popularity, it only makes sense that companies like Benchmade and Spyderco with the Roadie would begin to investigate the slip joint market.

Slipjoints are a very traditional style of knife designed so that a steel spring runs down the spine of the knife, the tension of that spring on the tang of the blade holds the knife open or closed. This design has been around for hundreds and hundreds of years so they’re really nothing new but I do believe that they are seeing a more widespread adoption in the last few years.

General Dimensions and Blade Details

Let’s get some specs before the review:

Blade Length: 2.75” (by my reckoning, BM puts it at 2.86”)
Overall Length: 6.625” (again by my ruler, BM states 6.69”)
Weight: 2.4oz (BM states 2.32oz)
Steel: CPM-S30V
Country of Manufacture: USA

Like most traditional folders, the Proper is an EDC knife through and through.

The Proper is available in two different blade shapes a sheep’s foot/wharncliffe type deal, and a clip point. At the risk of over simplifying the matter, I think that the clip point probably looks the best whereas the sheep’s foot is the most functional. I haven’t handled the clip personally, so take that with a grain of salt.

The sheep’s foot is exceptionally useful though, and is ideal for draw cuts when breaking down boxes, or slicing food. The blade stock is .09 thick steel and tapers to a nice .026 behind the edge. If you want to make it REAL crazy you can see if you can get a reground Krein version that is a literal lightsaber.

So how about the steel? S30V is a tried and true workhorse. Developed by Crucible with the help of legendary knife maker Chris Reeve, intended to hold a fine sharp edge for a long time, as well as having a very healthy amount of chromium making it extremely rust resistant.

In my experience, I find S30V to be a little chippy (in fact my Proper has a little chip out of the edge). Sharpening it is easy enough, and the edge does last a long time, to some extent S30V has become a little ho-hum in the realm of super steels. It’s still a performer though, and I do recommend it.

Handle and Ergonomics

The Proper, at the time of this review, is available in two handle materials. The first being red G10, and the second being the (more popular) green micarta. In terms of material I think they are equal, both G10 and micarta will stand up to a lot of wear and tear. They both offer a decent amount of grip traction for your hand in normal EDC use (what you’d use a slip joint for, no skinning wild boars or Hollywood-style knife fights).

The shape of the handle provides a great grip as well, with two very slight depending angles or you might call them quasi-choils on either end of the handle lock my pointer, middle, and ring fingers in place. The knife also has a bit of a badonkadonk, with a larger handle that extends past the downward angle of the choil, giving you an even more secure grip on the knife itself. That some extension also houses the lanyard hole.

I think all-in-all the knife is well designed for its intended use. This is not going to be a knife that you’re going to put through serious/hard work. A folding, non-locking, knife like this you’re going to perform pretty lightweight tasks.

Walk and Talk

So, the knife does not technically lock. It’s held in its various positions by the tension of the backspring. That being said, the Proper has a softer action than I’ve felt on other slip joints. Customs that I have had, or even GEC’s have very positive “walk and talks,” or the feeling and sound of the knife moving into its different positions.

I would prefer a positive action on the knife throughout, but when opened it doesn’t feel insecure.

Benchmade Proper Review – Final Thoughts

All things said and done, I think that the Benchmade Proper offers a lot to be had in terms of a modern/non-traditional slip joint. More interesting than that, however, I think seeing knives like this, the Spyderco Roadie, and even the Hinderer XM18 slippy hitting the marketplace shows an interesting trend when it comes to how people are choosing to spend their money.

If you had told me two years ago that I’d see a Hinderer slip joint or that Benchmade was making their own version of a non-locking folder I would have thought you were nuts, but here we are. I think the value is there, you’re going to spend nearly the same for a new Great Eastern Cutlery slippy, but you’re getting a modern design with a modern blade steel, versus GEC’s tried and true 1095.

If you’re not a slip joint guy, I think the Benchmade Proper is a great place to start. And if you’re already “in the fold,” then maybe it’s a good way to diversify your collection.

COLD STEEL AD-10 3.5" S35VN Steel Ultra-Sharp Drop Point Blade 5.25" G-10 Handle Tactical Folding Knife with Tri-Ad Locking Mechanism

CONSTRUCTION - The AD-10 tactical folding knife features an ultra-wide, ground thin at the edge, honed to razor-sharpness blade that offers unprecedented cutting, shearing, and piercing power while resisting bending, breaking, or chipping
S35VN STEEL BLADE - Crafted from S35VN steel, the AD-10 folding knife's blade ensures super-fine cutting edges and exceptional edge retention; This premium steel is renowned for its durability and ability to maintain sharpness through rigorous use
STRONG HANDLE - The handle of the AD-10 knife boasts heat-treated, full-length aluminum liners and 3D machined G-10 scales, providing unparalleled strength and grip; Its precise contouring and integral finger guard ensure a snug and secure fit in the hand
TRI-AD LOCK - Complete with the Tri-Ad, the AD-10 offers unrivaled strength, shock resistance, and durability; This reliable locking mechanism provides peace of mind, safeguarding your fingers during use and ensuring the blade remains securely in place
SPECS - Weight: 7 oz (198.4 g); Blade Thickness: 3.8 mm; Blade Length: 3 1/2"; Blade Steel: S35VN; Handle Length/Material: 5 1/4" G-10; Overall Length: 8 3/4"; Knife Type: Folder; Blade Shape: Drop Point; Locking Mechanism: Tri-Ad Lock

Editor: I recommend purchasing the Benchmade Proper at Amazon or BladeHQ. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade 560 Freek Review

by Dan Jackson 11 Comments

Last Updated: July 15, 2019

As much as I enjoy picking up the latest “gee whiz” must have knife of the moment, I get the most satisfaction in sharing a great knife that may have flown under the radar. This particular knife has flown so far under the radar, I would not have even heard about it if reader Darren hadn’t gone out of his way to send me a couple emails about the knife and how much he enjoyed it. Thank you, Darren.

Buy the Benchmade Freek at BladeHQ

Buy on Amazon

Enter the Benchmade 560 Freek. Like our friend the Bruised Forehead, the Freek didn’t win the knife name lottery. It also doesn’t benefit from being designed by a high profile knifemaker. And I don’t recall much in the way of fanfare from Benchmade or the knife collector community when the Freek arrived on the scene. It was quietly released. Rather than being a subject of media attention, the Freek has slowly earned a reputation for being a practical tool from those who have given this unassuming knife a chance.

I liken the Freek to the Benchmade Volli, another no-frills knife that didn’t get much attention, but may be be one of the best all-round EDC knives that Benchmade has released in the past 5 years. The Freek is cut from the same cloth. It’s another function over form design that is worth consideration if you are in the marketing for a largish EDC knife.

General Dimensions and Blade Details

The Freek has an overall length of 8.46″, a 3.6″ blade, and it weighs 3.72 ounces. This knife is made in America. As I mentioned earlier, I’d classify the 560 Freek as a large EDC knife. It could possibly be used as a hunting knife, as it has a good belly and shares the blade profile of their Saddle Mountain Skinner. Of course a knife of this size could also be used as a duty knife for a police officer, or perhaps pressed in to other self defense type applications. This is a versatile knife.

The drop point blade is distinguished by a curving thumb ramp and high flat grind. The blade is 2.9mm thick, and gets thin behind the edge thanks in part to that high flat grind. The edge has been neatly applied, and like on pretty much all the Benchmades I’ve owned over the years there, is a sharpening choil allowing you to sharpen the edge all the way down to the heel. The tip is fine, but the the deep belly keeps it out of the way. Again, this lends me to believe this could be a decent hunting knife, although frankly I’ve never been on a hunt in my life.

Benchmade has gone with tried and true S30V steel for the Freek. Although S30V has fallen slightly out of favor thanks to the widespread adoption of it’s more exotic cousin S35VN, I find that Benchmade does a particularly good job with their S30V. Case in point my Volli with its 2.5mm thick blade cuts like almost nothing else I own. That thing is a laser. The Freek is right up there. This knife is a phenomenal slicer, the S30V blade holds an excellent edge, and I found it to be an easy edge to maintain with strops and the ceramic rods from my Spyderco Sharpmaker.

This knife makes quick work of cardboard, laughs in the face of of your lunchtime apple, and will capably assist you with all those odd cutting tasks that crop up in our daily lives. Much like the Volli, the Freek is a knife that I looked forward to busting out when it came time to break down a box or open a package. It’s a performer and the S30V blade steel punches above its weight thanks to the heat treat and grind.

Handle, Ergonomics, and Pocket Clip

The handle is where things get interesting, and also where the knife is bound to alienate a significant section of the audience. Like the Griptilian, this is a plastic handled knife with partial stainless steel liners. Unlike the Griptilian, the Freek has a unique high density rubber (“Versaflex”) overmold that is bonded to the plastic. The end result is a lightweight grippy design that is unlike anything else in my collection.

Some will love the lightweight nature of the design and the non-slip feel to the handle. Others will dismiss it as being cheap and plasticy. If you couldn’t stand the feel of the handles of the original Griptilian, then my guess is you will want to skip the Freek. But if you don’t mind trading G10 for a large ultra light knife, then the Freek could be a winner for you.

The ergonomics of the Freek benefit from a streamlined handle design. There are few curves, and little reliance on jimping except for the thumb ramp. Although the handle is textured, it’s not an abrasive knife in the hand. The end result is a no-frills handle that is comfortable and secure in all kinds of conditions. The Freek easily accommodates my larger hand, and the handle is well suited for extended use and hard tasks.

This knife comes from the factory with Benchmade’s split arrow clip. I’ve long been a fan of this clip, and here it is situated for ambidextrous tip-up only carry. This is a discrete knife that and buries deeply in the pocket. Benchmade left part of the FRN endoskeleton exposed where the pocket clip meets the handle, and that makes for easy insertion and extraction of the knife from your pocket.

At well under 4 ounces I found the Freek to be an easy knife to tote around. It’s about as thick as the Griptilian and carries comparably. On that note, it’s worth stating that the Freek is actually almost half an inch longer than the Griptilian but weighs .16 ounces less.

Deployment and Lockup

There isn’t a whole heck of a lot new here to say in this section. This is a thumb stud axis lock knife. A tried and true design. Here the thumb studs and phosphor bronze washers work just as great as they did on my original Griptilian. While bearings are all the rage, I think something needs to be said for bronze washers. Especially for a thumb stud equipped user knife like the Freek. Bronze washers are still exceptionally smooth and are ideal for working knives like this.

I continue to appreciate the axis lock for it’s simple and intuitive design. Plus I always appreciate that this is a fully ambidextrous knife. Lockup is secure, but as you would expect from a plastic handled partial liner axis lock knife, there is a little side to side blade play. Nothing to get upset about, just a trade off in the design. Personally, I’m happy to exchange a modicum of side to side blade play for all the practicality and utility that this design offers. Your mileage may vary.

Blade centering is pretty good. It slightly favors the pocket clip side of my knife, and is far from rubbing.

Benchmade 560 Freek Review – Final Thoughts

For those wanting a premium lightweight work knife with an over 3.5″ blade, I think the Freek is a no-brainer. Benchmade has been refining this type of knife for years. It’s like a Griptilian but it is leaner and meaner, yet also slightly larger. Perhaps it’s oriented slightly more towards the lightweight camping and hunting ground. Benchmade doesn’t offer much insight in their product descriptions, but for some reason I keep going back to hunting when I consider the Freek.

Those that can’t stand the plastic scales on the original Griptilian would be well served to steer clear of the Freek. Instead check out the Volli or the G-10 Griptilian. Those models will also provide you with great cutting performance and ergonomics, but will also be a little stouter than the Freek.

I am glad Darren called this model to my attention. I hope in writing this review I have turned at least a couple people on to an excellent “sleeper” knife from Benchmade.

Benchmade - Freek 560, Drop-Point Blade, Plain Edge, Satin Finish, Black/Grey Versaflex Handle, Made in the USA

HIGH-QUALITY: The CPM-S30V stainless steel blade is extremely well-balanced, offering superb edge qualities and rust resistance. The Grivory and Versaflex dual durometer handle offers strength, comfort, and grip.
WELL-DESIGNED: Benchmade's AXIS lock is exceptionally strong and fully ambidextrous. The Freek 560 is a manual knife that can be opened and closed with either hand.
ALWAYS READY: The 560's quick, one-handed opening makes it easy to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Freek 560's drop-point, utility blade style and all-around functionality make it ideal for everyday carry.

I recommend purchasing the Benchmade 560 Freek at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade 530 / 531 Review

by A Sharp Guest Contributor 8 Comments

Last Updated: July 28, 2019
Shopping on Amazon for knives is a dangerous endeavor. Not only can you find a nearly endless variety of blades, but your account also has a nasty habit of learning your interests. You might not notice it at first. A simple suggestion, “I noticed you like Spyderco. Have you heard of Benchmade?” and suddenly your limited understanding of quality production knives enters a larger world.

Buy the Benchmade 530 at BladeHQ

Buy on Amazon

It was during the earliest stages of my newfound fanaticism for knives that Amazon did its now dreaded, “get yourself a little something,” and I saw it: The Benchmade 530. It had come up in my searches before. Like an expert hypnotist, the online shopping site had long implanted it in my psyche. I was drawn to the clean lines, the spear-point blade, and the overall symmetry. Benchmade’s Axis lock system and sparkling online reputation caught my attention. Also, I had been really good lately. So I succumbed to the siren’s call: I “got myself a little something.” I purchased the Benchmade 530 and fell one more step down the rabbit hole.

General Dimensions and Blade Details

The Benchmade 530 sports a 3.25” blade and an overall length of 7.42”. The knife is designed by Benchmade’s champion Mel Pardue. Those familiar with Pardue will recognize him as the designer of the Griptilian. Under the hood this knife shares some similar design traits with the Griptilian: reinforced plastic handles, partial liners, and the use of 154CM steel. I tend to view the 530 as a sort of companion piece to the Griptilian; a more elegant and svelte cousin to the rough-and-tumble Grip.

The 530’s blade is a satin-finished or black coated spear point with a long flat edge that terminates in a short and narrow belly. There is also the option to add a semi-serrated blade if it is your preference. The thin blade is ground into a dagger profile with a huge swedge dividing the blade evenly down the middle. This style is very similar to the stiletto style found on some of Mel Pardue’s custom offerings.

To the unfamiliar this blade may appear to be double-edged, but one side has been left unsharpened as a faux edge. Just as well, because a double edge would be illegal to carry in many states. The shape has led many uninitiated people to refer to the 530 as a switchblade, a comparison that is figuratively double-edged. On one hand the knife is probably intimidating enough to repel a would be mugger. On the other, flicking the blade to open a bag of beef jerky might raise some eyebrows at the mall. Just something to consider.

On paper this blade may look impractical for every-day-carry purposes due to the small belly and dagger grind, but in practice the performance is pleasing. 154CM steel is a staple of Benchmade’s, and for good reason. It is an American mid-range steel that is a good all around performer. The blade’s dagger shape serves several purposes. The deep swedge softens the feel of the back of the knife allowing you to rest your thumb more comfortably on the spine. If you have handled a Spyderco Dragonfly you will have a pretty good idea of how a swedge can bring a little more comfort.

The blade stock is already very thin at 2.29mm, but the grind on this knife makes the blade even more narrow and light while maintaining a strong tip. Because of this, it is a good slicer and excellent piercer. One thing to note about the blade is that it is so thin that it is possible to flex it ever so slightly, but not enough to be troubling for your every day tasks like opening packages or breaking down boxes. That said, I would be cautious to use this knife for hard use activities and it certainly wouldn’t be the only knife I’d bring along on a serious camping trip. While knives with swedges tend to slice a little more poorly than a full flat grind this knife is ground so thin that it seldom has any issue. Still, if a dagger grind isn’t your cup of tea, Benchmade also makes the 531 which sports a full flat ground drop point instead.

All in all, I like the 530’s style. It is what drew me to the knife in the first place and it has proven to be far more practical in practice than one would think.

Handle, Ergonomics, and Pocket Clip

The handle on the 530 is a fiberglass-reinforced nylon called Grivory. Benchmade has received both praise and criticism for similar handle materials in the past. Some people find the plastic cheap and flimsy. I happen to find most FRN handles to be lightweight and deceptively durable, the 530 being no exception. If you aren’t like me and you dislike plastic handles Benchmade again has your solution in the 531, which has handsome gray G10 handles. The 531 weighs a little more than the 530 because of this, but I would think hardly enough to be noticed.

The handle is coffin-shaped; meaning the blade of this knife is relatively straight and nearly symmetrical. Again, like the blade, the handle is deceptively functional. The plastic handles are hollow, but reinforced by bands of plastic segmenting the inner spaces. The back of the handle is mostly of closed construction with only a little bit of flow through where the frame peeks out. It is quite spacious; I can get a four-finger hold on the knife and still have room to spare. I wear a medium sized glove, so I think all but the very largest of hands will be accommodated in full. The plastic handle flares out on every corner, creating a convenient guard that locks the hand in place. These flares create a short finger ramp for exerting more pressure on the blade if required. Because the knife is flared on both ends, it is equally comfortable and functional in a reverse grip.

Some gently notched jimping is cut into the partial frame that is exposed almost exactly like on Pardue’s Griptilian, and like the Griptilian this jimping is appreciated but not particularly effective. There are also grooves set into the handle, light contouring to improve grip, and a very small divot where the thumb stud protrudes when closed that functions as a tiny choil when open. There was some gritty texture on the handle of my example around the chamfered edges. I am not sure if this is to make the knife more grippy or if it was a flaw, but I didn’t like it. Eventually I took some light grit sandpaper to it and it smoothed out easily. This leads me to believe that it probably would have smoothed out with time anyway.

Overall, the handle is functional and comfortable, but do not expect Spyderco or Griptilian-level ergonomics. Honestly, I don’t think anyone would consider this knife if they were just looking for good ergos. Rather, this knife’s charm lies in the thinness and lightness of its construction. This is achieved with a partial steel liner that only extends halfway down the hollowed handle and by the lightness of the blade. This guy is seriously svelte at 1.88 ounces, and with a handle of a mere 0.37th of an inch. You barely even feel it, yet it has a full-length intimidating blade.

By comparison, a Victorinox Alox Cadet is only 0.28 ounces lighter and shares roughly the same width. That being said, one of my favorite uses for this knife is when I go out for a run. I can clip it to my basketball shorts pocket and it doesn’t affect me, nor does it threaten to come loose and fall out. I imagine this knife would also be useful to pack-weight conscious hikers and climbers as well as for those looking for an unobtrusive defensive/practical tool to slip into a purse or pocket.

The 530 uses a standard Benchmade split arrow style pocket clip that is painted black. The handle is tapped for tip up, right or left side carry. The clip holds the knife on the pocket, but beyond that I do not like it. It does not bury the knife deeply in the pocket at all. I’d say that roughly ¾ of an inch of the handle sticks out over the edge of the pocket. Deep carry isn’t a huge issue when I pick a knife, but on this one it seems inappropriately shallow. I don’t like that it is simply painted either. It tends to chip and look tacky fairly quickly. The arrow shape is also problematic in my eye. It kept catching the hem threads on my T-shirts and tearing them out as well as slipping into the loops of my pocket stitches and loosening them. On my knife I felt the clip held too tight.

Ultimately, I didn’t want to let a knife I loved be brought down by a clip I didn’t. I contacted Benchmade through email and they immediately sent me a new polished deep-carry pocket clip without charge. I have to commend them on their great customer service. The new clip arrived in a couple of days and I popped it right on. Some slight adjustments later (ie, squishing it between two 2×4’s) and it was 100% perfect. Every issue I had with the old clip was resolved and I have never looked back.

Lastly, I will mention that this knife has a lanyard hole. It is situated on the corner of the butt closest to the closed side of the handle. It appears to be functional (I have never personally seen a need for a lanyard on this knife) and capable of fitting a single run of 550 paracord.

The handle on the 530 is light, relatively tough, and functional. I’d say that it is fairly no nonsense while still complimenting the same overall feel of the blade. That said, I don’t think that this is a knife that would be comfortable for long periods of hard use, but that falls in line with design intent anyway. And it sure looks nice.

Deployment and Lockup

The Benchmade 530 makes use of the company’s proprietary Axis Lock system with dual thumb studs and bronze phosphor washers. The axis lock is quite possibly my favorite design of locking mechanism for a lot of reasons. It is strong, reliable, fast, smooth, completely ambidexterous and incredibly elegant. It keeps one’s fingers free of the blade’s path during closing, which is great for the absent-minded fiddling I tend to do with it. I will note that unlike a lot of Benchmade’s axis locks, the lock bar studs on the 530 are a kind of concave cupped design as opposed to a more convex stacked shape. Unfortunately I have noticed that the cup style is less comfortable, having more of an edge to dig into the fingers. Fortunately, if this is an issue for you, the 531 has you covered, having the standard design. I think that the cupped studs are an attempt to keep the knife profile low and they don’t really bother me, even if I wish they were more standard.

Another thing of note is the so-called “landing gear” style of thumb studs. These reflect the overarching goal of this knife to be slim, as they are only about as wide as the handle at its thickest point. Some people have complained that the thumb studs make this knife hard to flick open. I had issues with this at first as well, but through use I found that if I used the groove leading up to the stud as a guide as I flicked my thumb I could deploy the blade quickly every time. If you can do that, this knife will be a smooth operator for you as well.

Benchmade 530 – Final Thoughts

The 530 is a knife not without its quirks. It is an ultra light, ultra thin EDC option that could easily be pressed into an emergency defensive role if needed. The knife is sturdy enough for regular use, but not quite as robust as some other offerings. If a harder use blade is your preference I could easily recommend better Benchmade models for the task, but I feel like the 530 fills a nice role in their line and for one of the most moderate prices in their catalogue: just under 100 dollars on Amazon.

I really love the 530 because it fills that same unique role in my collection and it has some killer good looks, but in all honesty the 531 is probably a better knife. It seems like it addresses most issues customers may have perceived in the 530. Still, I am not at all disappointed in my purchase and I would easily recommend the Benchmade 530 for anyone looking for a lean, mean knife.

Benchmade 531 Axis

HIGH-QUALITY: The 154CM stainless steel blade is tough, rust resistant, and holds an edge well. The G10 handle is durable, impervious to moisture, and stable under extreme temperatures.
WELL-DESIGNED: Benchmade's AXIS lock is exceptionally strong and fully ambidextrous. The 531 is a manual knife that can be opened and closed with either hand.
ALWAYS READY: The 531's lightweight design and one-handed opening make it easy to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The 531's drop-point, utility blade style and all-around functionality make it ideal for everyday carry.
SERVICES AND BENEFITS: For information and terms regarding Benchmade's Limited Warranty and LifeSharp Service, please visit Benchmade's website.

I recommend purchasing the Benchmade 530 at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

This was a guest review by Jacob Vandenberg. Jacob is a regular reader and all around good guy.

Benchmade 15080-2 Crooked River Review

by Dan Jackson 33 Comments

Last Updated: July 19, 2019

It’s no secret that I think the creative team at Benchmade has been adrift for the past few years. This is perhaps best evidenced by the fact that the company’s most exciting new offerings are actually re-issues of old models: the 940-1 and 551-1. These rockstar designs are interspersed among more puzzling offerings like the 808 Loco and 300 Axis Flipper.

Buy the Benchmade Crooked River at BladeHQ

Buy on Amazon

But Benchmade does seem to be cobbling together a theme. They seem to be taking this “old school, meet new school” approach not only to their classic designs, but also by melding traditional designs with modern manufacturing in their “Hunt” lineup. I thought the Small Summit Lake was a successful mashup of traditional lockback folder with modern materials, beefy construction, and precision manufacturing. The 15080 Crooked River is a knife cut from that same cloth.

In fact, the Crooked River takes the juxtoposition even further. This is an even greater departure from tradition to the point where we almost have a caricature of the classic bowie. Yet there is still a timeless quality to the knife. The low slung blade and bolstered handles tug at the heartstrings of traditional knife design, while the finishes and flourishes appeal to this fan of modern folding knives.

General Dimensions and Blade Details

The Crooked River has an overall length of 9.3″, a 4″ blade, weighs 5.41 ounces, and is made in the USA. This is a big knife, and is far outside the confines of what I would consider to be an every day carry (EDC) piece. If you were to whip this out in public to trim packing tape or open an envelope, most people would hide under their desk. And if a friend offered up a Swiss Army Knife at a campsite, you could go full Crocodile Dundee on the guy with this Crooked River. This is a “knoife”. I wouldn’t mind a smaller, more manageable version for daily carry.

The Crooked River features a long and lean clip point blade. I have always enjoyed a good clip point for it’s practicality, and the Crooked River is no exception. The high flat grind has been nicely executed complete with Benchmade’s 2-tone stonewashed satin finish. The blade is cut from an impressive 3.15mm thick piece of S30V stainless steel, and it carries a significant amount of steel out all the way to the tip. The end result is a blade that has a good tip for piercing, plenty of edge for cutting, and a nice belly for food prep and possibly even skinning.

The choice of S30V stainless steel for the blade is less exciting now then it may have been 5 years ago. These days I prefer S35VN for it’s improved toughness and ease of sharpening over S30V, but in my opinion Benchmade has always done a great job with their S30V. For example, the S30V on the Volli continues to impress me with it’s sharpness, edge holding, and ease of maintenance. I think Benchmade knows how to make the most of this steel.

The blade geometry of the Crooked River is stouter than the Volli, but this is still a functional blade and the S30V performs nicely on this knife. Capable of taking a keen edge, and holding it for an acceptable period of time, the S30V on the Crooked River is still functional despite there being sexier steels on the market. No issues with corrosion either.

Handle, Ergonomics, and Pocket Clip

The Crooked River has a long curving handle that compliments its long curving blade. The combination of diamond wood, aluminum bolsters, and orange pivot collar is striking, and I am sure that decision alone has sold many 15080-2’s for Benchmade. If resin-injected wood isn’t your thing, then Benchmade also offers the Crooked River with smooth gray G10 handle scales.

Underneath the scales are full stainless steel liners (skeletonized) and a bright orange G-10 backspacer. Holding things together is a large black pivot and blackened steel hardware. Everything is precision fit, and there are a number of nice details to enjoy, like the arced face between handle scale and bolster, the geared backspacer, and of course the snazzy orange pivot collar. Even the lanyard hole is oval and chamfered, adding style to an otherwise mundane feature of a knife.

Despite there being a good deal of weight around the pivot, the balance point on the Crooked River is behind the axis lock, and is close to the “hump” of the finger choil. The hand feels most at home here; set back further on the knife. While this isn’t billed as a tactical folder, I would be curious to get someone like Chad’s take on the Crooked River. I have no doubt that a knife like this could be pressed beyond pure utilitarian purposes if the need arose.

Beyond my comments on the balance of the knife, the Crooked River benefits from a subdued approach to ergonomics and traction. The long handle provides plenty of room, even for extra large hands. The diamond wood scales offers some texture (not much), while a mild run of jimping on the back of the handle indexes the thumb while still allowing the user to cut with the knife for extended periods without significant thumb fatigue. All said, the ergonomics have proven to be adequate for my purposes.

The Crooked River is a big knife. While I don’t think 5.41 ounces is overweight given the build quality and footprint, it’s still substantial, and when closed the knife is pivot heavy. This creates something of a pendulum effect in your pocket. Benchmade has tried to counter this with a stiff pocket clip. This is a good idea, and my Crooked River holds firmly in place.

On the subject of pocket clips, Benchmade went with a black parkerized version of their split arrow clip. I have always liked the split arrow clip, and here it is situated high on the handle for a relatively deep and discrete carry. The handle is also drilled and tapped for ambidextrous tip up use. That said, Benchmade’s deep carry clip will fit on this knife, and if you prefer a more discrete deep carry option Benchmade typically will send you a deep carry clip free of charge if you ask them nicely.

Deployment and Lockup

While some may grow bored with the axis lock, it remains one of my favorite locking mechanisms. I like the easy one handed opening and closing. Plus it’s fully ambidextrous. And I don’t know if I am simply bullshitting myself, but to me it looks like the phosphor bronze washers on these Benchmades have gotten thicker over the years. Much like my new 551-1, this Crooked River is smooth and easy to open. The blade pops into place with a satisfying “snick”, and the ambidextrous thumb studs are easy to get at with either hand.

Unlike some of the axis lock knives that have crossed my path, my Crooked River locks up tightly and without any play. Blade play is a common complaint on axis lock knives, but I have found that most knives can be fixed with a targeted application of Loctite. Here, blade play was a non-issue, and the axis lock remains as practical and easy to use as ever.

Benchmade Crooked River Review – Final Thoughts

Not to get all jingoistic on everyone, but the Crooked River appeals to the red blooded American in me. This knife takes me back to my childhood, handling my dad’s old Buck fixed blade tucked away his closet next to the well worn Swiss army knives, and old harmonicas.

There is an undeniable charm to the Crooked River that strikes at that primal note that has drawn many people to knife collecting in the first place. While not the most practical offering for an erudite urban EDC, the Crooked River is unapologetically bold and beautiful, and I think it is one of the nicer new designs from BM.

The Crooked River is a knife that I would like a smaller version of. As it stands I don’t see it getting a ton of use personally, but perhaps it has a place in your collection. If the Crooked River piques your interest in the same way that it piqued mine, then I am pleased to report that it is a well made and satisfying folder.

Benchmade - Crooked River 15080 EDC Knife with Wood Handle (15080-2)

BUILT FOR THE HUNT: Simplicity and style meets unmatched function, no matter the application; An ideal hunting knife capable of countless tasks in the field.
CPM-S30V STEEL: For first-rate edge retention and corrosion resistance; Clip-point construction for easily controlled cuts. Factory in Oregon City, Oregon.
STABILIZED WOOD HANDLE: Is made from a durable composite material that's been backfilled with resin; Stands up to a range of harsh elements and environments; Stronger than natural wood.
AXIS LOCKING MECHANISM: Ensures safety and a smooth open and easy close; Reversible split arrow clip; Lanyard hole for versatile carry options.

I recommend purchasing the Benchmade Crooked River at Amazon or BladeHQ. Please consider that purchasing anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.

Benchmade G10 Griptilian 551-1 Review

by Dan Jackson 29 Comments

I wasn’t one of those guys that had a big issue with the plastic handles on the original Griptilian. I always thought they were light and durable. Maybe not the sexiest choice of materials, but certainly practical. But for many the plastic handles of the Griptilian were a source of contention at best. At worst they were a deal breaker.

Buy the Benchmade G-10 Griptilian at BladeHQ

Buy on Amazon

So for the longest time if you wanted a Griptilian with G-10 handle scales, you had to go to the after market. This market was pioneered by ex-pat Kevin Wilkins. His line of WilkinsGRIP aftermarket scales were the enthusiast’s best choice if you wanted a G10 Griptilian.

Benchmade finally came around in late 2015 and released both the 551-1 Griptilian and 556-1 Mini Griptilian with G-10 handles. This is arguably the most exciting thing Benchmade has done since the 940-1 Osborne.

This knife was provided to me free of charge by the fine folks over at KnifeArt. In no way has this impacted my impressions of the 551-1. I think the people over at KnifeArt are good guys, I think they run a quality website, and I appreciate their letting me check out this 551-1. Now on to the review.

General Dimensions and Blade Details

The 551-1 has an overall length of 8.07″, a 3.45″ blade, weighs 4.17 ounces and is made in the USA. The G10 version is almost an ounce heavier than the original Griptilian, but it does not feel heavy for it’s size, and seems significantly lighter than my WilkinsGRIP equipped BM 552 / Ritter Griptilian.

The 551-1 has an identical drop point blade to the original Griptilian and is offered with your choice of thumb stud or thumb oval. I always preferred the look of the thumb stud version of the Griptilian, so that is what I got.

When I compare this blade to my original Griptilian the only difference I can detect is that the blade has been given a bit of a stonewash. Of course, the 551-1 features a new blade steel, and I will talk about that below. But beyond that you have the same excellent blade shape of the original Griptilian, with a saber flat grind, and swedge. This classic drop point shape has served me well for many years now.

Besides the switch to G-10 scales, the biggest news about the 551-1 is change to CPM-20CV blade steel. This is a steel that I was previously unfamiliar with. Manufactured by Crucible Industries, CPM-20CV is advertised as a steel with high corrosion resistance and wear resistance, and good toughness. Chemically it is similar to M390, which is an excellent steel. CPM-20CV has an extremely high chromium content, which results in its corrosion resistant qualities. From what I can gather, this appears to be a good choice for a folding knife. It may not have the toughness of a steel like 3V, but I think the extra corrosion resistance is a nice trade off here. My regular 154CM Griptilian has been through the ringer, and it occasionally shows small spots of rust if I forget to clean it.

My 551-1 came razor sharp from the factory, and this 20CV seems to hold an edge well. So far I have used the knife to break down a few boxes, open mail, etc. I haven’t wailed on this knife like my original Griptilian and so far have only needed to gently strop the knife to maintain its edge. No corrosion or complaints thus far, but I am not 100% convinced that this steel is worth the price premium over regular 154CM to me.

Still, it’s an interesting steel and I intend to keep this knife for long term testing and evaluation. I’ll update this review as I “gather more data points” and use the knife in the coming years. So far so good.

Handle, Ergonomics, and Pocket Clip

Obviously the handle is the main event here for the 551-1, and is basically the entire point of this knife. I am pleased to say that this new G10 handle has been beautifully executed. It is fully 3-D machined, and features bright blue liners and anodized blue backspacers beneath gray overlays. I am not sure if the gray-blue combo would have been my first choice, but the blue certainly “pops” here and my handle has been flawlessly executed. I am hoping Benchmade will roll out some other color combos in the future.

Like the original Griptilian the 551-1 features partial nested steel liners. That is about the only similarity with the handle construction of the original Griptilian. Even the hardware has been upgraded on the 551-1. This new handle is a totally different animal and it transforms the look and feel of the knife.

My favorite aspect of the new handle is how they shaped it to match the contours of the original Griptilian. If you handle aftermarket scales for a Griptilian, they are usually very big and boxy. These aftermarket handles change the ergonomics substantially and add additional weight. That is not the case for the 551-1. Here you get a feel in hand that is very faithful to the original FRN Grip. Of course there is a little extra weight, and the G-10 does feel slightly different, but the overall profile and hand filling nature of the original model has not been lost in translation. Benchmade did away with some of the extra texturing on the handle, and the diamond pattern here isn’t quite as grippy as on the original knife, but there is plenty of grip here for me and I’d go so far as to say that this is an improvement over the original knife from an ergonomics perspective.

Benchmade decided to include a deep carry pocket clip on the new 551-1 rather than their original spoon clip. I like this deep carry clip. It makes for a discrete knife that I have actually worn with slacks at work a few times now. This is a proven clip design. I think the 551-1 carries well for what it is. This is a larger knife, and it is heavier than it’s FRN predecessor, but this is still something that normal guys can carry and use and I think this is a viable EDC option (although admittedly the mini-551-1 is really all you will need for 99% of your EDC tasks).

Deployment and Lockup

Benchmade has equipped the 551-1 with an impressively beefy set of phosphor bronze washers. Because you have an open back design, the washers are very prominent on this knife. The blade flicks open effortlessly. This is a satisfying knife to open and close. Whether you decide on the thumb stud version or the thumb hole version I don’t think you will have a problem accessing the blade.

Of course for lock up you have an axis lock here. I have discussed the axis lock for years now. It remains one of my favorite locks as it is fully ambidextrous and allows you to easily open and close the knife with one hand. I find that the use of G10 handle scales adds a lot of structural rigidity to an axis lock knife and the 551-1 is no exception. It feels solid, and may inspire more confidence in the end user than FRN.

Blade centering is perfect on my knife, as I would expect from a nearly $200 folder.

Benchmade 551-1 Review – Final Thoughts

I must admit I was somewhat skeptical about this knife given the enormous price premium over the regular FRN verion, but the 551-1 has been beautifully executed, and I can see where the extra money went. They didn’t just slap some G10 on this thing and call it a day – every single facet of the original Griptilian has been re-considered and in someway upgraded. It’s clear Benchmade spent a lot of time and effort to dial in the 551-1.

Compared to its FRN predecessor, this new 551-1 is simply a superior tool. If the original FRN scales drove you up the wall, then the 551-1 cures that ill handily, and if you are a Griptilian fan I’d say this is basically a “must buy”. I was skeptical at first, especially given the price point, but the 551-1 has exceeded my expectations.

Benchmade - Griptilian 551-1 Knife, Drop-Point Blade, Plain Edge, Satin Finish, Gray Handle G10 Handle, Made in the USA

HIGH-QUALITY: The CPM-S30V stainless steel blade is extremely well-balanced, offering superb edge qualities and rust resistance. The glass-filled nylon handle is tough yet attractive, making it ideal for hard jobs and everyday carry.
WELL-DESIGNED: Benchmade's AXIS lock is exceptionally strong and fully ambidextrous. The Griptilian 551 is a manual knife that can be opened and closed single-handedly.
COMFORTABLE: The 551's lightweight design and handle grips make it comfortable to hold and use. The reversible pocket clip offers ultimate accessibility.
VERSATILE: The Griptilian 551's drop-point utility blade style and all-around functionality make it ideal for everyday use, outdoor activities and even tactical applications.

I recommend buying the 551-1 at Amazon, or BladeHQ, KnifeArt.com. Please consider that buying anything through any of the links on this website helps support BladeReviews.com, and keeps the site going. As always, any and all support is greatly appreciated. Thank you very much.